ngram
listlengths 0
10.5k
|
|---|
[
"latest release (as of 20 January 2018) * PETG from Das Filament I",
"1.1.8 * Bed auto leveling before each print * Slic3r Prusa Edition, latest",
"big deal, but it's annoying because it's stopping the part of having a",
"the nozzle starts fading out as it comes closer to the point of",
"layer of a cube. The nozzle first prints the perimeters ok. Then it",
"a big deal, but it's annoying because it's stopping the part of having",
"nice first layer and finish. My setup is: * Anet A6 running Marlin",
"part, beginning from one corner and finishing on the opposite one. As the",
"finishing a layer, the flow of plastic through the nozzle starts fading out",
"but the issue persists. I'm beginning to think that this could be a",
"* PETG from Das Filament I tried disabling all \"retract\" settings but the",
"bug (Slic3r), but before I submit it to GitHub, I'd like to be",
"As an example, let's say that I'm printing the first layer of a",
"deal, but it's annoying because it's stopping the part of having a very",
"print * Slic3r Prusa Edition, latest release (as of 20 January 2018) *",
"when the printer is finishing a layer, the flow of plastic through the",
"think that this could be a software bug (Slic3r), but before I submit",
"nozzle starts fading out as it comes closer to the point of layer",
"corner and finishing on the opposite one. As the nozzle comes closer to",
"print the inner part, beginning from one corner and finishing on the opposite",
"have observed that when the printer is finishing a layer, the flow of",
"resulting in the lines of the filament to touching each other. Maybe it's",
"from one corner and finishing on the opposite one. As the nozzle comes",
"tried disabling all \"retract\" settings but the issue persists. I'm beginning to think",
"Prusa Edition, latest release (as of 20 January 2018) * PETG from Das",
"settings but the issue persists. I'm beginning to think that this could be",
"release (as of 20 January 2018) * PETG from Das Filament I tried",
"that this could be a software bug (Slic3r), but before I submit it",
"touching each other. Maybe it's not a big deal, but it's annoying because",
"one. As the nozzle comes closer to the finishing corner, the flow of",
"to touching each other. Maybe it's not a big deal, but it's annoying",
"on the opposite one. As the nozzle comes closer to the finishing corner,",
"As the nozzle comes closer to the finishing corner, the flow of plastic",
"(Slic3r), but before I submit it to GitHub, I'd like to be sure.",
"closer to the point of layer change. As an example, let's say that",
"the flow of plastic diminishes, resulting in the lines of the filament to",
"example, let's say that I'm printing the first layer of a cube. The",
"the lines of the filament to touching each other. Maybe it's not a",
"through the nozzle starts fading out as it comes closer to the point",
"beginning to think that this could be a software bug (Slic3r), but before",
"that I'm printing the first layer of a cube. The nozzle first prints",
"flow of plastic through the nozzle starts fading out as it comes closer",
"a very nice first layer and finish. My setup is: * Anet A6",
"the part of having a very nice first layer and finish. My setup",
"I'm beginning to think that this could be a software bug (Slic3r), but",
"disabling all \"retract\" settings but the issue persists. I'm beginning to think that",
"a software bug (Slic3r), but before I submit it to GitHub, I'd like",
"I tried disabling all \"retract\" settings but the issue persists. I'm beginning to",
"it's stopping the part of having a very nice first layer and finish.",
"Anet A6 running Marlin 1.1.8 * Bed auto leveling before each print *",
"nozzle first prints the perimeters ok. Then it begins to print the inner",
"the point of layer change. As an example, let's say that I'm printing",
"\"retract\" settings but the issue persists. I'm beginning to think that this could",
"of having a very nice first layer and finish. My setup is: *",
"of the filament to touching each other. Maybe it's not a big deal,",
"comes closer to the finishing corner, the flow of plastic diminishes, resulting in",
"having a very nice first layer and finish. My setup is: * Anet",
"filament to touching each other. Maybe it's not a big deal, but it's",
"beginning from one corner and finishing on the opposite one. As the nozzle",
"Filament I tried disabling all \"retract\" settings but the issue persists. I'm beginning",
"I submit it to GitHub, I'd like to be sure. Any opinion is",
"finishing on the opposite one. As the nozzle comes closer to the finishing",
"opposite one. As the nozzle comes closer to the finishing corner, the flow",
"of plastic diminishes, resulting in the lines of the filament to touching each",
"annoying because it's stopping the part of having a very nice first layer",
"observed that when the printer is finishing a layer, the flow of plastic",
"first layer of a cube. The nozzle first prints the perimeters ok. Then",
"an example, let's say that I'm printing the first layer of a cube.",
"leveling before each print * Slic3r Prusa Edition, latest release (as of 20",
"all \"retract\" settings but the issue persists. I'm beginning to think that this",
"that when the printer is finishing a layer, the flow of plastic through",
"the nozzle comes closer to the finishing corner, the flow of plastic diminishes,",
"printing the first layer of a cube. The nozzle first prints the perimeters",
"is: * Anet A6 running Marlin 1.1.8 * Bed auto leveling before each",
"it comes closer to the point of layer change. As an example, let's",
"the opposite one. As the nozzle comes closer to the finishing corner, the",
"Maybe it's not a big deal, but it's annoying because it's stopping the",
"but it's annoying because it's stopping the part of having a very nice",
"PETG from Das Filament I tried disabling all \"retract\" settings but the issue",
"I'm printing the first layer of a cube. The nozzle first prints the",
"running Marlin 1.1.8 * Bed auto leveling before each print * Slic3r Prusa",
"in the lines of the filament to touching each other. Maybe it's not",
"to the point of layer change. As an example, let's say that I'm",
"perimeters ok. Then it begins to print the inner part, beginning from one",
"first prints the perimeters ok. Then it begins to print the inner part,",
"but before I submit it to GitHub, I'd like to be sure. Any",
"finishing corner, the flow of plastic diminishes, resulting in the lines of the",
"The nozzle first prints the perimeters ok. Then it begins to print the",
"issue persists. I'm beginning to think that this could be a software bug",
"software bug (Slic3r), but before I submit it to GitHub, I'd like to",
"before each print * Slic3r Prusa Edition, latest release (as of 20 January",
"of 20 January 2018) * PETG from Das Filament I tried disabling all",
"of layer change. As an example, let's say that I'm printing the first",
"point of layer change. As an example, let's say that I'm printing the",
"to think that this could be a software bug (Slic3r), but before I",
"layer and finish. My setup is: * Anet A6 running Marlin 1.1.8 *",
"begins to print the inner part, beginning from one corner and finishing on",
"the inner part, beginning from one corner and finishing on the opposite one.",
"could be a software bug (Slic3r), but before I submit it to GitHub,",
"plastic diminishes, resulting in the lines of the filament to touching each other.",
"stopping the part of having a very nice first layer and finish. My",
"starts fading out as it comes closer to the point of layer change.",
"be a software bug (Slic3r), but before I submit it to GitHub, I'd",
"a layer, the flow of plastic through the nozzle starts fading out as",
"of plastic through the nozzle starts fading out as it comes closer to",
"to the finishing corner, the flow of plastic diminishes, resulting in the lines",
"Slic3r Prusa Edition, latest release (as of 20 January 2018) * PETG from",
"it's not a big deal, but it's annoying because it's stopping the part",
"the flow of plastic through the nozzle starts fading out as it comes",
"other. Maybe it's not a big deal, but it's annoying because it's stopping",
"* Bed auto leveling before each print * Slic3r Prusa Edition, latest release",
"say that I'm printing the first layer of a cube. The nozzle first",
"layer change. As an example, let's say that I'm printing the first layer",
"each print * Slic3r Prusa Edition, latest release (as of 20 January 2018)",
"one corner and finishing on the opposite one. As the nozzle comes closer",
"Bed auto leveling before each print * Slic3r Prusa Edition, latest release (as",
"ok. Then it begins to print the inner part, beginning from one corner",
"corner, the flow of plastic diminishes, resulting in the lines of the filament",
"the finishing corner, the flow of plastic diminishes, resulting in the lines of",
"not a big deal, but it's annoying because it's stopping the part of",
"prints the perimeters ok. Then it begins to print the inner part, beginning",
"inner part, beginning from one corner and finishing on the opposite one. As",
"this could be a software bug (Slic3r), but before I submit it to",
"cube. The nozzle first prints the perimeters ok. Then it begins to print",
"the filament to touching each other. Maybe it's not a big deal, but",
"* Anet A6 running Marlin 1.1.8 * Bed auto leveling before each print",
"plastic through the nozzle starts fading out as it comes closer to the",
"part of having a very nice first layer and finish. My setup is:",
"Marlin 1.1.8 * Bed auto leveling before each print * Slic3r Prusa Edition,",
"persists. I'm beginning to think that this could be a software bug (Slic3r),",
"(as of 20 January 2018) * PETG from Das Filament I tried disabling",
"it's annoying because it's stopping the part of having a very nice first",
"very nice first layer and finish. My setup is: * Anet A6 running",
"I've have observed that when the printer is finishing a layer, the flow",
"fading out as it comes closer to the point of layer change. As",
"from Das Filament I tried disabling all \"retract\" settings but the issue persists.",
"and finish. My setup is: * Anet A6 running Marlin 1.1.8 * Bed",
"Edition, latest release (as of 20 January 2018) * PETG from Das Filament",
"2018) * PETG from Das Filament I tried disabling all \"retract\" settings but",
"20 January 2018) * PETG from Das Filament I tried disabling all \"retract\"",
"change. As an example, let's say that I'm printing the first layer of",
"the issue persists. I'm beginning to think that this could be a software",
"is finishing a layer, the flow of plastic through the nozzle starts fading",
"Das Filament I tried disabling all \"retract\" settings but the issue persists. I'm",
"the first layer of a cube. The nozzle first prints the perimeters ok.",
"before I submit it to GitHub, I'd like to be sure. Any opinion",
"because it's stopping the part of having a very nice first layer and",
"let's say that I'm printing the first layer of a cube. The nozzle",
"setup is: * Anet A6 running Marlin 1.1.8 * Bed auto leveling before",
"My setup is: * Anet A6 running Marlin 1.1.8 * Bed auto leveling",
"of a cube. The nozzle first prints the perimeters ok. Then it begins",
"layer, the flow of plastic through the nozzle starts fading out as it",
"a cube. The nozzle first prints the perimeters ok. Then it begins to",
"printer is finishing a layer, the flow of plastic through the nozzle starts",
"Then it begins to print the inner part, beginning from one corner and",
"closer to the finishing corner, the flow of plastic diminishes, resulting in the",
"January 2018) * PETG from Das Filament I tried disabling all \"retract\" settings",
"it begins to print the inner part, beginning from one corner and finishing",
"to print the inner part, beginning from one corner and finishing on the",
"auto leveling before each print * Slic3r Prusa Edition, latest release (as of",
"nozzle comes closer to the finishing corner, the flow of plastic diminishes, resulting",
"first layer and finish. My setup is: * Anet A6 running Marlin 1.1.8",
"diminishes, resulting in the lines of the filament to touching each other. Maybe",
"as it comes closer to the point of layer change. As an example,",
"comes closer to the point of layer change. As an example, let's say",
"and finishing on the opposite one. As the nozzle comes closer to the",
"* Slic3r Prusa Edition, latest release (as of 20 January 2018) * PETG",
"flow of plastic diminishes, resulting in the lines of the filament to touching",
"lines of the filament to touching each other. Maybe it's not a big",
"each other. Maybe it's not a big deal, but it's annoying because it's",
"out as it comes closer to the point of layer change. As an",
"submit it to GitHub, I'd like to be sure. Any opinion is welcome!",
"the printer is finishing a layer, the flow of plastic through the nozzle",
"finish. My setup is: * Anet A6 running Marlin 1.1.8 * Bed auto",
"A6 running Marlin 1.1.8 * Bed auto leveling before each print * Slic3r",
"the perimeters ok. Then it begins to print the inner part, beginning from"
] |
[
"to accomplish this? I am currently using Cura. It seems that the support",
"accomplish this? I am currently using Cura. It seems that the support material",
"the first layer, what is the best way to accomplish this? I am",
"what is the best way to accomplish this? I am currently using Cura.",
"am trying to print a model that requires support material to be on",
"that requires support material to be on the first layer, what is the",
"requires support material to be on the first layer, what is the best",
"layer, what is the best way to accomplish this? I am currently using",
"am currently using Cura. It seems that the support material is too flaky.",
"print a model that requires support material to be on the first layer,",
"the best way to accomplish this? I am currently using Cura. It seems",
"that the support material is too flaky. I have the infill for the",
"way to accomplish this? I am currently using Cura. It seems that the",
"support material to be on the first layer, what is the best way",
"I am currently using Cura. It seems that the support material is too",
"on the first layer, what is the best way to accomplish this? I",
"using Cura. It seems that the support material is too flaky. I have",
"to be on the first layer, what is the best way to accomplish",
"be on the first layer, what is the best way to accomplish this?",
"It seems that the support material is too flaky. I have the infill",
"is the best way to accomplish this? I am currently using Cura. It",
"material is too flaky. I have the infill for the support at around",
"this? I am currently using Cura. It seems that the support material is",
"first layer, what is the best way to accomplish this? I am currently",
"I am trying to print a model that requires support material to be",
"support material is too flaky. I have the infill for the support at",
"is too flaky. I have the infill for the support at around 8%",
"trying to print a model that requires support material to be on the",
"the support material is too flaky. I have the infill for the support",
"currently using Cura. It seems that the support material is too flaky. I",
"best way to accomplish this? I am currently using Cura. It seems that",
"Cura. It seems that the support material is too flaky. I have the",
"seems that the support material is too flaky. I have the infill for",
"a model that requires support material to be on the first layer, what",
"to print a model that requires support material to be on the first",
"material to be on the first layer, what is the best way to",
"model that requires support material to be on the first layer, what is"
] |
[
"to be both telemetry, and RC controlled. That cylinder should allow the signals,",
"is transparent to radio waves. I want to place my transmitter in a",
"my transmitter in a cylinder. That cylinder would be placed in a big",
"That cylinder should allow the signals, should be strong and light. So which",
"which is transparent to radio waves. I want to place my transmitter in",
"cylinder. That cylinder would be placed in a big RC plane ( whose",
"be placed in a big RC plane ( whose body is made up",
"for a plastic which is transparent to radio waves. I want to place",
"would be placed in a big RC plane ( whose body is made",
"both telemetry, and RC controlled. That cylinder should allow the signals, should be",
"signals, should be strong and light. So which material would you suggest and",
"a plastic which is transparent to radio waves. I want to place my",
"transparent to radio waves. I want to place my transmitter in a cylinder.",
"strong and light. So which material would you suggest and is that material",
"radio waves. I want to place my transmitter in a cylinder. That cylinder",
"to radio waves. I want to place my transmitter in a cylinder. That",
"waves. I want to place my transmitter in a cylinder. That cylinder would",
"( whose body is made up of cardboard). I want the plane to",
"of cardboard). I want the plane to be both telemetry, and RC controlled.",
"light. So which material would you suggest and is that material easy to",
"allow the signals, should be strong and light. So which material would you",
"transmitter in a cylinder. That cylinder would be placed in a big RC",
"in a cylinder. That cylinder would be placed in a big RC plane",
"placed in a big RC plane ( whose body is made up of",
"made up of cardboard). I want the plane to be both telemetry, and",
"plastic which is transparent to radio waves. I want to place my transmitter",
"I want the plane to be both telemetry, and RC controlled. That cylinder",
"should allow the signals, should be strong and light. So which material would",
"plane ( whose body is made up of cardboard). I want the plane",
"and RC controlled. That cylinder should allow the signals, should be strong and",
"big RC plane ( whose body is made up of cardboard). I want",
"and light. So which material would you suggest and is that material easy",
"controlled. That cylinder should allow the signals, should be strong and light. So",
"cylinder should allow the signals, should be strong and light. So which material",
"looking for a plastic which is transparent to radio waves. I want to",
"want to place my transmitter in a cylinder. That cylinder would be placed",
"RC plane ( whose body is made up of cardboard). I want the",
"That cylinder would be placed in a big RC plane ( whose body",
"whose body is made up of cardboard). I want the plane to be",
"a big RC plane ( whose body is made up of cardboard). I",
"plane to be both telemetry, and RC controlled. That cylinder should allow the",
"should be strong and light. So which material would you suggest and is",
"a cylinder. That cylinder would be placed in a big RC plane (",
"I am looking for a plastic which is transparent to radio waves. I",
"material would you suggest and is that material easy to do 3d print?",
"to place my transmitter in a cylinder. That cylinder would be placed in",
"be strong and light. So which material would you suggest and is that",
"So which material would you suggest and is that material easy to do",
"up of cardboard). I want the plane to be both telemetry, and RC",
"cylinder would be placed in a big RC plane ( whose body is",
"the plane to be both telemetry, and RC controlled. That cylinder should allow",
"RC controlled. That cylinder should allow the signals, should be strong and light.",
"in a big RC plane ( whose body is made up of cardboard).",
"am looking for a plastic which is transparent to radio waves. I want",
"is made up of cardboard). I want the plane to be both telemetry,",
"the signals, should be strong and light. So which material would you suggest",
"telemetry, and RC controlled. That cylinder should allow the signals, should be strong",
"I want to place my transmitter in a cylinder. That cylinder would be",
"be both telemetry, and RC controlled. That cylinder should allow the signals, should",
"which material would you suggest and is that material easy to do 3d",
"want the plane to be both telemetry, and RC controlled. That cylinder should",
"cardboard). I want the plane to be both telemetry, and RC controlled. That",
"place my transmitter in a cylinder. That cylinder would be placed in a",
"body is made up of cardboard). I want the plane to be both"
] |
[
"steps:0, Printing Temp:240 C, Build plate Temp:65 C, Diameter: 2.85 mm, Dimensions of",
"to my problem. Printing quality dropped when i try to write vertical axis",
"I am a beginner in 3D printing field. I read couple of answers",
"to write vertical axis (i mean, columns). There is no problem in horizontal",
"0.4 mm. I think I should write 0.5 mm column with 0.4 mm",
"diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm, Top bottom",
"Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm, Top",
"a beginner in 3D printing field. I read couple of answers in forums",
"height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1 mm, Infill density: 100 %,",
"with ease. I added messy structure to this post and you can find",
"field. I read couple of answers in forums and i cannot find exact",
"in 3D printing field. I read couple of answers in forums and i",
"try to write vertical axis (i mean, columns). There is no problem in",
"you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What",
"details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your suggestion to",
"nozzle diameter is 0.4 mm. I think I should write 0.5 mm column",
"couple of answers in forums and i cannot find exact answer to my",
"this problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm,",
"mm nozzle with ease. I added messy structure to this post and you",
"axis. My column width must be 0.5 mm, and printer nozzle diameter is",
"Top bottom thickness:1 mm, Infill density: 100 %, Gradual infill steps:0, Printing Temp:240",
"find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your",
"think? What is your suggestion to overcome this problem? Printer:Ultimaker 3, Slicer:Cura, Printing",
"Layer height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1 mm, Infill density: 100",
"infill steps:0, Printing Temp:240 C, Build plate Temp:65 C, Diameter: 2.85 mm, Dimensions",
"with 0.4 mm nozzle with ease. I added messy structure to this post",
"mm, Wall thickness:1 mm, Top bottom thickness:1 mm, Infill density: 100 %, Gradual",
"thickness:1 mm, Infill density: 100 %, Gradual infill steps:0, Printing Temp:240 C, Build",
"my problem. Printing quality dropped when i try to write vertical axis (i",
"What is your suggestion to overcome this problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details;",
"Printing quality dropped when i try to write vertical axis (i mean, columns).",
"%, Gradual infill steps:0, Printing Temp:240 C, Build plate Temp:65 C, Diameter: 2.85",
"100 %, Gradual infill steps:0, Printing Temp:240 C, Build plate Temp:65 C, Diameter:",
"Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1 mm,",
"thickness:1 mm, Top bottom thickness:1 mm, Infill density: 100 %, Gradual infill steps:0,",
"nozzle with ease. I added messy structure to this post and you can",
"problem. Printing quality dropped when i try to write vertical axis (i mean,",
"writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your suggestion",
"0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1 mm, Infill",
"Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1",
"and 3D printer users; I am a beginner in 3D printing field. I",
"and printer nozzle diameter is 0.4 mm. I think I should write 0.5",
"mm, Infill density: 100 %, Gradual infill steps:0, Printing Temp:240 C, Build plate",
"mean, columns). There is no problem in horizontal axis. My column width must",
"answer to my problem. Printing quality dropped when i try to write vertical",
"read couple of answers in forums and i cannot find exact answer to",
"problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer",
"structure to this post and you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg)",
"do you think? What is your suggestion to overcome this problem? Printer:Ultimaker 3,",
"horizontal axis. My column width must be 0.5 mm, and printer nozzle diameter",
"am a beginner in 3D printing field. I read couple of answers in",
"i try to write vertical axis (i mean, columns). There is no problem",
"column with 0.4 mm nozzle with ease. I added messy structure to this",
"Temp:240 C, Build plate Temp:65 C, Diameter: 2.85 mm, Dimensions of the material:10X10X5",
"Wall thickness:1 mm, Top bottom thickness:1 mm, Infill density: 100 %, Gradual infill",
"quality dropped when i try to write vertical axis (i mean, columns). There",
"mm, Layer height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1 mm, Infill density:",
"overcome this problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1",
"mm, Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm, Top bottom thickness:1",
"vertical axis (i mean, columns). There is no problem in horizontal axis. My",
"axis (i mean, columns). There is no problem in horizontal axis. My column",
"density: 100 %, Gradual infill steps:0, Printing Temp:240 C, Build plate Temp:65 C,",
"(i mean, columns). There is no problem in horizontal axis. My column width",
"problem in horizontal axis. My column width must be 0.5 mm, and printer",
"in forums and i cannot find exact answer to my problem. Printing quality",
"Gradual infill steps:0, Printing Temp:240 C, Build plate Temp:65 C, Diameter: 2.85 mm,",
"Structure](https://i.stack.imgur.com/VbBo0.jpg)](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your suggestion to overcome this problem?",
"is no problem in horizontal axis. My column width must be 0.5 mm,",
"messy structure to this post and you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What",
"I should write 0.5 mm column with 0.4 mm nozzle with ease. I",
"C, Build plate Temp:65 C, Diameter: 2.85 mm, Dimensions of the material:10X10X5 mm",
"mm, and printer nozzle diameter is 0.4 mm. I think I should write",
"added messy structure to this post and you can find writing details below.",
"when i try to write vertical axis (i mean, columns). There is no",
"is 0.4 mm. I think I should write 0.5 mm column with 0.4",
"in horizontal axis. My column width must be 0.5 mm, and printer nozzle",
"My column width must be 0.5 mm, and printer nozzle diameter is 0.4",
"should write 0.5 mm column with 0.4 mm nozzle with ease. I added",
"[](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your suggestion to overcome this",
"is your suggestion to overcome this problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle",
"3D printer users; I am a beginner in 3D printing field. I read",
"mm column with 0.4 mm nozzle with ease. I added messy structure to",
"to overcome this problem? Printer:Ultimaker 3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine",
"mm. I think I should write 0.5 mm column with 0.4 mm nozzle",
"be 0.5 mm, and printer nozzle diameter is 0.4 mm. I think I",
"and you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think?",
"users; I am a beginner in 3D printing field. I read couple of",
"0.5 mm, and printer nozzle diameter is 0.4 mm. I think I should",
"printer nozzle diameter is 0.4 mm. I think I should write 0.5 mm",
"forums and i cannot find exact answer to my problem. Printing quality dropped",
"ease. I added messy structure to this post and you can find writing",
"Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall thickness:1 mm,",
"think I should write 0.5 mm column with 0.4 mm nozzle with ease.",
"3D printing field. I read couple of answers in forums and i cannot",
"column width must be 0.5 mm, and printer nozzle diameter is 0.4 mm.",
"below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is your suggestion to overcome",
"mm, Top bottom thickness:1 mm, Infill density: 100 %, Gradual infill steps:0, Printing",
"you think? What is your suggestion to overcome this problem? Printer:Ultimaker 3, Slicer:Cura,",
"can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you think? What is",
"0.5 mm column with 0.4 mm nozzle with ease. I added messy structure",
"no problem in horizontal axis. My column width must be 0.5 mm, and",
"Infill density: 100 %, Gradual infill steps:0, Printing Temp:240 C, Build plate Temp:65",
"I think I should write 0.5 mm column with 0.4 mm nozzle with",
"printing field. I read couple of answers in forums and i cannot find",
"width must be 0.5 mm, and printer nozzle diameter is 0.4 mm. I",
"What do you think? What is your suggestion to overcome this problem? Printer:Ultimaker",
"experts and 3D printer users; I am a beginner in 3D printing field.",
"cannot find exact answer to my problem. Printing quality dropped when i try",
"of answers in forums and i cannot find exact answer to my problem.",
"answers in forums and i cannot find exact answer to my problem. Printing",
"beginner in 3D printing field. I read couple of answers in forums and",
"I read couple of answers in forums and i cannot find exact answer",
"post and you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do you",
"and i cannot find exact answer to my problem. Printing quality dropped when",
"this post and you can find writing details below. [](https://i.stack.imgur.com/VbBo0.jpg) What do",
"columns). There is no problem in horizontal axis. My column width must be",
"Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1 mm, Wall",
"i cannot find exact answer to my problem. Printing quality dropped when i",
"write 0.5 mm column with 0.4 mm nozzle with ease. I added messy",
"Dear experts and 3D printer users; I am a beginner in 3D printing",
"3, Slicer:Cura, Printing Details; Nozzle diameter:0.4 mm, Profile:Fine 0.1 mm, Layer height:0.1 mm,",
"dropped when i try to write vertical axis (i mean, columns). There is"
] |
[
"tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat... When I now print the",
"I get X25mm, Y20mm & Z19.5mm. Could the issue be with the firmare",
"the firmare being upgraded to Marlin? The cube was sliced by Cura and",
"printer, Github Marlin, Repetier Host, Cura slicer Just setting up printer and printed",
"I stop the print and ask Repetier to move the steppers the distance",
"Marlin? The cube was sliced by Cura and I have used the same",
"setting up printer and printed 20mm calibration cube from Thingiverse. X,Y,Z & E",
"firmware to Marlin. I ran several iterations of request travel, measure result and",
"too far off but not quite right (centre hole was oval not round)",
"Y20mm & Z19.5mm. Could the issue be with the firmare being upgraded to",
"Marlin. I ran several iterations of request travel, measure result and tweek stepper",
"Z19.5mm. Could the issue be with the firmare being upgraded to Marlin? The",
"and I have used the same file for all of the prints. When",
"cube from Thingiverse. X,Y,Z & E not too far off but not quite",
"help and updated firmware to Marlin. I ran several iterations of request travel,",
"move the steppers the distance is as they should be for a 100mm",
"updated firmware to Marlin. I ran several iterations of request travel, measure result",
"with the firmare being upgraded to Marlin? The cube was sliced by Cura",
"Followed Youtube calibration help and updated firmware to Marlin. I ran several iterations",
"not quite right (centre hole was oval not round) X19.5mm, Y19.5mm & Z20mm.",
"(M501,M92xxxx, M500) Live Die Repeat... When I now print the calibration cube I",
"the calibration cube I get X25mm, Y20mm & Z19.5mm. Could the issue be",
"measure result and tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat... When I",
"now print the calibration cube I get X25mm, Y20mm & Z19.5mm. Could the",
"for all of the prints. When I stop the print and ask Repetier",
"quite right (centre hole was oval not round) X19.5mm, Y19.5mm & Z20mm. Followed",
"Live Die Repeat... When I now print the calibration cube I get X25mm,",
"hole was oval not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help",
"I have used the same file for all of the prints. When I",
"the same file for all of the prints. When I stop the print",
"Marlin, Repetier Host, Cura slicer Just setting up printer and printed 20mm calibration",
"and tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat... When I now print",
"Repetier to move the steppers the distance is as they should be for",
"used the same file for all of the prints. When I stop the",
"travel, measure result and tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat... When",
"far off but not quite right (centre hole was oval not round) X19.5mm,",
"be with the firmare being upgraded to Marlin? The cube was sliced by",
"Just setting up printer and printed 20mm calibration cube from Thingiverse. X,Y,Z &",
"was oval not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help and",
"round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help and updated firmware to",
"When I now print the calibration cube I get X25mm, Y20mm & Z19.5mm.",
"upgraded to Marlin? The cube was sliced by Cura and I have used",
"Anet A8 printer, Github Marlin, Repetier Host, Cura slicer Just setting up printer",
"was sliced by Cura and I have used the same file for all",
"Repetier Host, Cura slicer Just setting up printer and printed 20mm calibration cube",
"Y19.5mm & Z20mm. Followed Youtube calibration help and updated firmware to Marlin. I",
"cube I get X25mm, Y20mm & Z19.5mm. Could the issue be with the",
"stepper settings (M501,M92xxxx, M500) Live Die Repeat... When I now print the calibration",
"from Thingiverse. X,Y,Z & E not too far off but not quite right",
"E not too far off but not quite right (centre hole was oval",
"right (centre hole was oval not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube",
"same file for all of the prints. When I stop the print and",
"get X25mm, Y20mm & Z19.5mm. Could the issue be with the firmare being",
"cube was sliced by Cura and I have used the same file for",
"A8 printer, Github Marlin, Repetier Host, Cura slicer Just setting up printer and",
"not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help and updated firmware",
"Z20mm. Followed Youtube calibration help and updated firmware to Marlin. I ran several",
"X25mm, Y20mm & Z19.5mm. Could the issue be with the firmare being upgraded",
"and printed 20mm calibration cube from Thingiverse. X,Y,Z & E not too far",
"to Marlin? The cube was sliced by Cura and I have used the",
"result and tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat... When I now",
"oval not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help and updated",
"iterations of request travel, measure result and tweek stepper settings (M501,M92xxxx, M500) Live",
"printed 20mm calibration cube from Thingiverse. X,Y,Z & E not too far off",
"file for all of the prints. When I stop the print and ask",
"I now print the calibration cube I get X25mm, Y20mm & Z19.5mm. Could",
"Cura and I have used the same file for all of the prints.",
"Thingiverse. X,Y,Z & E not too far off but not quite right (centre",
"the steppers the distance is as they should be for a 100mm travel.",
"calibration cube from Thingiverse. X,Y,Z & E not too far off but not",
"Cura slicer Just setting up printer and printed 20mm calibration cube from Thingiverse.",
"settings (M501,M92xxxx, M500) Live Die Repeat... When I now print the calibration cube",
"not too far off but not quite right (centre hole was oval not",
"but not quite right (centre hole was oval not round) X19.5mm, Y19.5mm &",
"have used the same file for all of the prints. When I stop",
"20mm calibration cube from Thingiverse. X,Y,Z & E not too far off but",
"prints. When I stop the print and ask Repetier to move the steppers",
"Host, Cura slicer Just setting up printer and printed 20mm calibration cube from",
"The cube was sliced by Cura and I have used the same file",
"Could the issue be with the firmare being upgraded to Marlin? The cube",
"ask Repetier to move the steppers the distance is as they should be",
"all of the prints. When I stop the print and ask Repetier to",
"calibration cube I get X25mm, Y20mm & Z19.5mm. Could the issue be with",
"the prints. When I stop the print and ask Repetier to move the",
"issue be with the firmare being upgraded to Marlin? The cube was sliced",
"request travel, measure result and tweek stepper settings (M501,M92xxxx, M500) Live Die Repeat...",
"and ask Repetier to move the steppers the distance is as they should",
"Repeat... When I now print the calibration cube I get X25mm, Y20mm &",
"printer and printed 20mm calibration cube from Thingiverse. X,Y,Z & E not too",
"by Cura and I have used the same file for all of the",
"X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration help and updated firmware to Marlin.",
"of the prints. When I stop the print and ask Repetier to move",
"off but not quite right (centre hole was oval not round) X19.5mm, Y19.5mm",
"ran several iterations of request travel, measure result and tweek stepper settings (M501,M92xxxx,",
"up printer and printed 20mm calibration cube from Thingiverse. X,Y,Z & E not",
"(centre hole was oval not round) X19.5mm, Y19.5mm & Z20mm. Followed Youtube calibration",
"sliced by Cura and I have used the same file for all of",
"slicer Just setting up printer and printed 20mm calibration cube from Thingiverse. X,Y,Z",
"Github Marlin, Repetier Host, Cura slicer Just setting up printer and printed 20mm",
"to Marlin. I ran several iterations of request travel, measure result and tweek",
"M500) Live Die Repeat... When I now print the calibration cube I get",
"stop the print and ask Repetier to move the steppers the distance is",
"to move the steppers the distance is as they should be for a",
"When I stop the print and ask Repetier to move the steppers the",
"of request travel, measure result and tweek stepper settings (M501,M92xxxx, M500) Live Die",
"and updated firmware to Marlin. I ran several iterations of request travel, measure",
"Youtube calibration help and updated firmware to Marlin. I ran several iterations of",
"I ran several iterations of request travel, measure result and tweek stepper settings",
"& Z20mm. Followed Youtube calibration help and updated firmware to Marlin. I ran",
"the issue be with the firmare being upgraded to Marlin? The cube was",
"calibration help and updated firmware to Marlin. I ran several iterations of request",
"the print and ask Repetier to move the steppers the distance is as",
"X,Y,Z & E not too far off but not quite right (centre hole",
"Die Repeat... When I now print the calibration cube I get X25mm, Y20mm",
"firmare being upgraded to Marlin? The cube was sliced by Cura and I",
"& Z19.5mm. Could the issue be with the firmare being upgraded to Marlin?",
"& E not too far off but not quite right (centre hole was",
"print and ask Repetier to move the steppers the distance is as they",
"several iterations of request travel, measure result and tweek stepper settings (M501,M92xxxx, M500)",
"print the calibration cube I get X25mm, Y20mm & Z19.5mm. Could the issue",
"being upgraded to Marlin? The cube was sliced by Cura and I have"
] |
[
"layers I think that covers everything, Let me know if I need to",
"first layer, I am doing 60 mm/s, just like the rest of my",
"dia. --> 0.4mm * Nozzle temp --> 210°C * Print speed --> 60",
"a good speed to print at for the first layer, I am doing",
"make that much of a difference? So other than that I don't know",
"0.4mm * Nozzle temp --> 210°C * Print speed --> 60 mm *",
"the filament to stick. I don't think I was adding too much, maybe",
"or some balling in rare situations. I use masking tape, which I found",
"have been playing around with the bed for a while and I still",
"off a print. I also use some glue stick, which seems to sometimes",
"the rest of my print. Any advice from there with first layers would",
"* Bed temp --> 50°C * I use masking tape on bed *",
"failed first layers. But when I do get the first layer done, the",
"filament over failed first layers. But when I do get the first layer",
"masking tape on bed * nozzle dia. --> 0.4mm * Nozzle temp -->",
"of a difference? So other than that I don't know what to try.",
"I am doing 60 mm/s, just like the rest of my print. Any",
"choice --> PLA * Fan is on after 3 layers I think that",
"doesn't allow the filament to stick. I don't think I was adding too",
"Any advice from there with first layers would be great. I am tired",
"Printer --> Anet A6 * Print area --> 220 x 220 mm *",
"to print at for the first layer, I am doing 60 mm/s, just",
"Fan is on after 3 layers I think that covers everything, Let me",
"tape, which I found for $3 at Dollar general. I heard something about",
"with first layers would be great. I am tired of wasting time and",
"of wasting time and filament over failed first layers. But when I do",
"seems to sometimes not help, almost like it doesn't allow the filament to",
"also use some glue stick, which seems to sometimes not help, almost like",
"glue stick, which seems to sometimes not help, almost like it doesn't allow",
"at for the first layer, I am doing 60 mm/s, just like the",
"210°C * Print speed --> 60 mm * Material of choice --> PLA",
"can't get the first layer to stick properly. I think I am getting",
"I was. But is glue stick needed? Does it really make that much",
"my print. Any advice from there with first layers would be great. I",
"after 3 layers I think that covers everything, Let me know if I",
"and filament over failed first layers. But when I do get the first",
"what is a good speed to print at for the first layer, I",
"masking tape, which I found for $3 at Dollar general. I heard something",
"use the paper method. But yet I find myself with the filament lifting",
"filament to stick. I don't think I was adding too much, maybe I",
"bed? --> Yes * Bed temp --> 50°C * I use masking tape",
"was. But is glue stick needed? Does it really make that much of",
"stick needed? Does it really make that much of a difference? So other",
"the first layer to stick properly. I think I am getting the bed",
"should be helpful for people: * Printer --> Anet A6 * Print area",
"masking tape worth it? I don't want to buy it because I would",
"And is more expensive masking tape worth it? I don't want to buy",
"to try. I can't get the first layer to work properly. Maybe it",
"a while and I still can't get the first layer to stick properly.",
"layer done, the second+ layers all work fine, no issues. Here are the",
"speed --> 60 mm * Material of choice --> PLA * Fan is",
"been playing around with the bed for a while and I still can't",
"I don't know what to try. I can't get the first layer to",
"with the bed for a while and I still can't get the first",
"So other than that I don't know what to try. I can't get",
"of my print. Any advice from there with first layers would be great.",
"Print speed --> 60 mm * Material of choice --> PLA * Fan",
"bed * nozzle dia. --> 0.4mm * Nozzle temp --> 210°C * Print",
"on after 3 layers I think that covers everything, Let me know if",
"I also use some glue stick, which seems to sometimes not help, almost",
"I can't get the first layer to work properly. Maybe it is my",
"printer, that should be helpful for people: * Printer --> Anet A6 *",
"getting pulled away with the nozzle or some balling in rare situations. I",
"first layers. But when I do get the first layer done, the second+",
"is a good speed to print at for the first layer, I am",
"print at for the first layer, I am doing 60 mm/s, just like",
"get the first layer to work properly. Maybe it is my speed, what",
"that important? And is more expensive masking tape worth it? I don't want",
"am getting the bed leveled good, I use the paper method. But yet",
"rest of my print. Any advice from there with first layers would be",
"filament lifting off and getting pulled away with the nozzle or some balling",
"But yet I find myself with the filament lifting off and getting pulled",
"for it to tear when I take off a print. I also use",
"use masking tape on bed * nozzle dia. --> 0.4mm * Nozzle temp",
"I find myself with the filament lifting off and getting pulled away with",
"rare situations. I use masking tape, which I found for $3 at Dollar",
"factor, but why is that important? And is more expensive masking tape worth",
"the bed for a while and I still can't get the first layer",
"some balling in rare situations. I use masking tape, which I found for",
"like the rest of my print. Any advice from there with first layers",
"don't know what to try. I can't get the first layer to work",
"for $3 at Dollar general. I heard something about shine being a factor,",
"being a factor, but why is that important? And is more expensive masking",
"bed leveled good, I use the paper method. But yet I find myself",
"I do get the first layer done, the second+ layers all work fine,",
"Material of choice --> PLA * Fan is on after 3 layers I",
"* Fan is on after 3 layers I think that covers everything, Let",
"I think that covers everything, Let me know if I need to add",
"temp --> 210°C * Print speed --> 60 mm * Material of choice",
"properly. Maybe it is my speed, what is a good speed to print",
"temp --> 50°C * I use masking tape on bed * nozzle dia.",
"think I was adding too much, maybe I was. But is glue stick",
"220 x 220 mm * Heated bed? --> Yes * Bed temp -->",
"expensive masking tape worth it? I don't want to buy it because I",
"try. I can't get the first layer to work properly. Maybe it is",
"* Print area --> 220 x 220 mm * Heated bed? --> Yes",
"it because I would hate for it to tear when I take off",
"mm/s, just like the rest of my print. Any advice from there with",
"with the filament lifting off and getting pulled away with the nozzle or",
"But is glue stick needed? Does it really make that much of a",
"I use masking tape, which I found for $3 at Dollar general. I",
"x 220 mm * Heated bed? --> Yes * Bed temp --> 50°C",
"why is that important? And is more expensive masking tape worth it? I",
"* I use masking tape on bed * nozzle dia. --> 0.4mm *",
"buy it because I would hate for it to tear when I take",
"* Nozzle temp --> 210°C * Print speed --> 60 mm * Material",
"stick. I don't think I was adding too much, maybe I was. But",
"tear when I take off a print. I also use some glue stick,",
"my speed, what is a good speed to print at for the first",
"Does it really make that much of a difference? So other than that",
"220 mm * Heated bed? --> Yes * Bed temp --> 50°C *",
"layer to stick properly. I think I am getting the bed leveled good,",
"Yes * Bed temp --> 50°C * I use masking tape on bed",
"get the first layer to stick properly. I think I am getting the",
"Heated bed? --> Yes * Bed temp --> 50°C * I use masking",
"hate for it to tear when I take off a print. I also",
"the first layer done, the second+ layers all work fine, no issues. Here",
"layers. But when I do get the first layer done, the second+ layers",
"tape worth it? I don't want to buy it because I would hate",
"playing around with the bed for a while and I still can't get",
"stick, which seems to sometimes not help, almost like it doesn't allow the",
"be great. I am tired of wasting time and filament over failed first",
"Dollar general. I heard something about shine being a factor, but why is",
"am tired of wasting time and filament over failed first layers. But when",
"the nozzle or some balling in rare situations. I use masking tape, which",
"mm * Heated bed? --> Yes * Bed temp --> 50°C * I",
"I found for $3 at Dollar general. I heard something about shine being",
"--> 210°C * Print speed --> 60 mm * Material of choice -->",
"stick properly. I think I am getting the bed leveled good, I use",
"think that covers everything, Let me know if I need to add anything",
"that should be helpful for people: * Printer --> Anet A6 * Print",
"layers all work fine, no issues. Here are the specs of my printer,",
"layers would be great. I am tired of wasting time and filament over",
"nozzle or some balling in rare situations. I use masking tape, which I",
"get the first layer done, the second+ layers all work fine, no issues.",
"good, I use the paper method. But yet I find myself with the",
"which seems to sometimes not help, almost like it doesn't allow the filament",
"Print area --> 220 x 220 mm * Heated bed? --> Yes *",
"I don't think I was adding too much, maybe I was. But is",
"* Print speed --> 60 mm * Material of choice --> PLA *",
"first layer to work properly. Maybe it is my speed, what is a",
"on bed * nozzle dia. --> 0.4mm * Nozzle temp --> 210°C *",
"is more expensive masking tape worth it? I don't want to buy it",
"first layer done, the second+ layers all work fine, no issues. Here are",
"much, maybe I was. But is glue stick needed? Does it really make",
"* Heated bed? --> Yes * Bed temp --> 50°C * I use",
"I think I am getting the bed leveled good, I use the paper",
"can't get the first layer to work properly. Maybe it is my speed,",
"that covers everything, Let me know if I need to add anything else.",
"situations. I use masking tape, which I found for $3 at Dollar general.",
"don't think I was adding too much, maybe I was. But is glue",
"3 layers I think that covers everything, Let me know if I need",
"it really make that much of a difference? So other than that I",
"of my printer, that should be helpful for people: * Printer --> Anet",
"I am tired of wasting time and filament over failed first layers. But",
"myself with the filament lifting off and getting pulled away with the nozzle",
"is glue stick needed? Does it really make that much of a difference?",
"in rare situations. I use masking tape, which I found for $3 at",
"but why is that important? And is more expensive masking tape worth it?",
"issues. Here are the specs of my printer, that should be helpful for",
"it to tear when I take off a print. I also use some",
"I take off a print. I also use some glue stick, which seems",
"help, almost like it doesn't allow the filament to stick. I don't think",
"layer, I am doing 60 mm/s, just like the rest of my print.",
"speed, what is a good speed to print at for the first layer,",
"balling in rare situations. I use masking tape, which I found for $3",
"Here are the specs of my printer, that should be helpful for people:",
"take off a print. I also use some glue stick, which seems to",
"are the specs of my printer, that should be helpful for people: *",
"would be great. I am tired of wasting time and filament over failed",
"nozzle dia. --> 0.4mm * Nozzle temp --> 210°C * Print speed -->",
"not help, almost like it doesn't allow the filament to stick. I don't",
"to stick properly. I think I am getting the bed leveled good, I",
"off and getting pulled away with the nozzle or some balling in rare",
"to buy it because I would hate for it to tear when I",
"But when I do get the first layer done, the second+ layers all",
"found for $3 at Dollar general. I heard something about shine being a",
"too much, maybe I was. But is glue stick needed? Does it really",
"wasting time and filament over failed first layers. But when I do get",
"just like the rest of my print. Any advice from there with first",
"Bed temp --> 50°C * I use masking tape on bed * nozzle",
"I have been playing around with the bed for a while and I",
"than that I don't know what to try. I can't get the first",
"really make that much of a difference? So other than that I don't",
"done, the second+ layers all work fine, no issues. Here are the specs",
"be helpful for people: * Printer --> Anet A6 * Print area -->",
"people: * Printer --> Anet A6 * Print area --> 220 x 220",
"the specs of my printer, that should be helpful for people: * Printer",
"to tear when I take off a print. I also use some glue",
"Anet A6 * Print area --> 220 x 220 mm * Heated bed?",
"difference? So other than that I don't know what to try. I can't",
"away with the nozzle or some balling in rare situations. I use masking",
"that I don't know what to try. I can't get the first layer",
"$3 at Dollar general. I heard something about shine being a factor, but",
"to sometimes not help, almost like it doesn't allow the filament to stick.",
"find myself with the filament lifting off and getting pulled away with the",
"pulled away with the nozzle or some balling in rare situations. I use",
"is on after 3 layers I think that covers everything, Let me know",
"it doesn't allow the filament to stick. I don't think I was adding",
"fine, no issues. Here are the specs of my printer, that should be",
"PLA * Fan is on after 3 layers I think that covers everything,",
"when I take off a print. I also use some glue stick, which",
"--> 60 mm * Material of choice --> PLA * Fan is on",
"it is my speed, what is a good speed to print at for",
"know what to try. I can't get the first layer to work properly.",
"don't want to buy it because I would hate for it to tear",
"general. I heard something about shine being a factor, but why is that",
"maybe I was. But is glue stick needed? Does it really make that",
"because I would hate for it to tear when I take off a",
"properly. I think I am getting the bed leveled good, I use the",
"other than that I don't know what to try. I can't get the",
"shine being a factor, but why is that important? And is more expensive",
"my printer, that should be helpful for people: * Printer --> Anet A6",
"good speed to print at for the first layer, I am doing 60",
"the first layer, I am doing 60 mm/s, just like the rest of",
"--> 0.4mm * Nozzle temp --> 210°C * Print speed --> 60 mm",
"I don't want to buy it because I would hate for it to",
"something about shine being a factor, but why is that important? And is",
"I am getting the bed leveled good, I use the paper method. But",
"A6 * Print area --> 220 x 220 mm * Heated bed? -->",
"doing 60 mm/s, just like the rest of my print. Any advice from",
"I was adding too much, maybe I was. But is glue stick needed?",
"second+ layers all work fine, no issues. Here are the specs of my",
"the filament lifting off and getting pulled away with the nozzle or some",
"needed? Does it really make that much of a difference? So other than",
"much of a difference? So other than that I don't know what to",
"over failed first layers. But when I do get the first layer done,",
"of choice --> PLA * Fan is on after 3 layers I think",
"all work fine, no issues. Here are the specs of my printer, that",
"to work properly. Maybe it is my speed, what is a good speed",
"want to buy it because I would hate for it to tear when",
"leveled good, I use the paper method. But yet I find myself with",
"print. Any advice from there with first layers would be great. I am",
"to stick. I don't think I was adding too much, maybe I was.",
"was adding too much, maybe I was. But is glue stick needed? Does",
"am doing 60 mm/s, just like the rest of my print. Any advice",
"the bed leveled good, I use the paper method. But yet I find",
"is that important? And is more expensive masking tape worth it? I don't",
"which I found for $3 at Dollar general. I heard something about shine",
"when I do get the first layer done, the second+ layers all work",
"think I am getting the bed leveled good, I use the paper method.",
"allow the filament to stick. I don't think I was adding too much,",
"great. I am tired of wasting time and filament over failed first layers.",
"print. I also use some glue stick, which seems to sometimes not help,",
"helpful for people: * Printer --> Anet A6 * Print area --> 220",
"heard something about shine being a factor, but why is that important? And",
"first layers would be great. I am tired of wasting time and filament",
"tired of wasting time and filament over failed first layers. But when I",
"--> Anet A6 * Print area --> 220 x 220 mm * Heated",
"60 mm * Material of choice --> PLA * Fan is on after",
"a print. I also use some glue stick, which seems to sometimes not",
"I heard something about shine being a factor, but why is that important?",
"mm * Material of choice --> PLA * Fan is on after 3",
"while and I still can't get the first layer to stick properly. I",
"about shine being a factor, but why is that important? And is more",
"a difference? So other than that I don't know what to try. I",
"no issues. Here are the specs of my printer, that should be helpful",
"I use masking tape on bed * nozzle dia. --> 0.4mm * Nozzle",
"Nozzle temp --> 210°C * Print speed --> 60 mm * Material of",
"do get the first layer done, the second+ layers all work fine, no",
"I still can't get the first layer to stick properly. I think I",
"worth it? I don't want to buy it because I would hate for",
"I use the paper method. But yet I find myself with the filament",
"adding too much, maybe I was. But is glue stick needed? Does it",
"and I still can't get the first layer to stick properly. I think",
"some glue stick, which seems to sometimes not help, almost like it doesn't",
"Maybe it is my speed, what is a good speed to print at",
"getting the bed leveled good, I use the paper method. But yet I",
"the second+ layers all work fine, no issues. Here are the specs of",
"--> PLA * Fan is on after 3 layers I think that covers",
"lifting off and getting pulled away with the nozzle or some balling in",
"for the first layer, I am doing 60 mm/s, just like the rest",
"* Material of choice --> PLA * Fan is on after 3 layers",
"--> 220 x 220 mm * Heated bed? --> Yes * Bed temp",
"tape on bed * nozzle dia. --> 0.4mm * Nozzle temp --> 210°C",
"still can't get the first layer to stick properly. I think I am",
"important? And is more expensive masking tape worth it? I don't want to",
"for a while and I still can't get the first layer to stick",
"method. But yet I find myself with the filament lifting off and getting",
"specs of my printer, that should be helpful for people: * Printer -->",
"a factor, but why is that important? And is more expensive masking tape",
"it? I don't want to buy it because I would hate for it",
"I would hate for it to tear when I take off a print.",
"advice from there with first layers would be great. I am tired of",
"that much of a difference? So other than that I don't know what",
"speed to print at for the first layer, I am doing 60 mm/s,",
"like it doesn't allow the filament to stick. I don't think I was",
"50°C * I use masking tape on bed * nozzle dia. --> 0.4mm",
"60 mm/s, just like the rest of my print. Any advice from there",
"is my speed, what is a good speed to print at for the",
"--> Yes * Bed temp --> 50°C * I use masking tape on",
"area --> 220 x 220 mm * Heated bed? --> Yes * Bed",
"work properly. Maybe it is my speed, what is a good speed to",
"--> 50°C * I use masking tape on bed * nozzle dia. -->",
"the paper method. But yet I find myself with the filament lifting off",
"glue stick needed? Does it really make that much of a difference? So",
"first layer to stick properly. I think I am getting the bed leveled",
"paper method. But yet I find myself with the filament lifting off and",
"* nozzle dia. --> 0.4mm * Nozzle temp --> 210°C * Print speed",
"use masking tape, which I found for $3 at Dollar general. I heard",
"yet I find myself with the filament lifting off and getting pulled away",
"more expensive masking tape worth it? I don't want to buy it because",
"what to try. I can't get the first layer to work properly. Maybe",
"layer to work properly. Maybe it is my speed, what is a good",
"for people: * Printer --> Anet A6 * Print area --> 220 x",
"the first layer to work properly. Maybe it is my speed, what is",
"* Printer --> Anet A6 * Print area --> 220 x 220 mm",
"time and filament over failed first layers. But when I do get the",
"use some glue stick, which seems to sometimes not help, almost like it",
"at Dollar general. I heard something about shine being a factor, but why",
"with the nozzle or some balling in rare situations. I use masking tape,",
"would hate for it to tear when I take off a print. I",
"there with first layers would be great. I am tired of wasting time",
"work fine, no issues. Here are the specs of my printer, that should",
"and getting pulled away with the nozzle or some balling in rare situations.",
"bed for a while and I still can't get the first layer to",
"almost like it doesn't allow the filament to stick. I don't think I",
"from there with first layers would be great. I am tired of wasting",
"around with the bed for a while and I still can't get the",
"sometimes not help, almost like it doesn't allow the filament to stick. I"
] |
[
"fan at 30% power ``` Can somebody suggest me how to write commands",
"= 'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is",
"to write any commands to it Here is the code: ``` ser =",
"at 30% power ``` Can somebody suggest me how to write commands to",
"= 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command to",
"able to read the data from the device but unable to write any",
"any commands to it Here is the code: ``` ser = serial.Serial() ser.port",
"data from the device but unable to write any commands to it Here",
"= serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14",
"Hyrel System 30M 3D Printer. I am able to read the data from",
"out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command to turn on",
"to connect to the Hyrel System 30M 3D Printer. I am able to",
"to it Here is the code: ``` ser = serial.Serial() ser.port = 'COM4'",
"= ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command to turn on the",
"with pySerial library to connect to the Hyrel System 30M 3D Printer. I",
"serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n')",
"the data from the device but unable to write any commands to it",
"pySerial library to connect to the Hyrel System 30M 3D Printer. I am",
"connect to the Hyrel System 30M 3D Printer. I am able to read",
"30M 3D Printer. I am able to read the data from the device",
"3.6 with pySerial library to connect to the Hyrel System 30M 3D Printer.",
"am able to read the data from the device but unable to write",
"library to connect to the Hyrel System 30M 3D Printer. I am able",
"3D Printer. I am able to read the data from the device but",
"30% power ``` Can somebody suggest me how to write commands to printer",
"but unable to write any commands to it Here is the code: ```",
"from the device but unable to write any commands to it Here is",
"Printer. I am able to read the data from the device but unable",
"to read the data from the device but unable to write any commands",
"command to turn on the fan at 30% power ``` Can somebody suggest",
"%This is the command to turn on the fan at 30% power ```",
"on the fan at 30% power ``` Can somebody suggest me how to",
"System 30M 3D Printer. I am able to read the data from the",
"is the code: ``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate = 38400",
"ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command",
"read the data from the device but unable to write any commands to",
"commands to it Here is the code: ``` ser = serial.Serial() ser.port =",
"the device but unable to write any commands to it Here is the",
"Here is the code: ``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate =",
"I am able to read the data from the device but unable to",
"T14 S30\\n') %This is the command to turn on the fan at 30%",
"S30\\n') %This is the command to turn on the fan at 30% power",
"``` Can somebody suggest me how to write commands to printer through python",
"'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is the",
"ser.port = 'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This",
"ser.write(b'M106 T14 S30\\n') %This is the command to turn on the fan at",
"to turn on the fan at 30% power ``` Can somebody suggest me",
"am using python 3.6 with pySerial library to connect to the Hyrel System",
"it Here is the code: ``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate",
"turn on the fan at 30% power ``` Can somebody suggest me how",
"ser = serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out = ser.readline() ser.write(b'M106",
"38400 out = ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command to turn",
"device but unable to write any commands to it Here is the code:",
"unable to write any commands to it Here is the code: ``` ser",
"ser.readline() ser.write(b'M106 T14 S30\\n') %This is the command to turn on the fan",
"is the command to turn on the fan at 30% power ``` Can",
"the command to turn on the fan at 30% power ``` Can somebody",
"``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out = ser.readline()",
"python 3.6 with pySerial library to connect to the Hyrel System 30M 3D",
"the Hyrel System 30M 3D Printer. I am able to read the data",
"the fan at 30% power ``` Can somebody suggest me how to write",
"to the Hyrel System 30M 3D Printer. I am able to read the",
"using python 3.6 with pySerial library to connect to the Hyrel System 30M",
"power ``` Can somebody suggest me how to write commands to printer through",
"write any commands to it Here is the code: ``` ser = serial.Serial()",
"I am using python 3.6 with pySerial library to connect to the Hyrel",
"the code: ``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out",
"code: ``` ser = serial.Serial() ser.port = 'COM4' ser.baudrate = 38400 out ="
] |
[
"happening to my motor. Any suggestions would help. 1. I have tried adjusting",
"here](https://i.stack.imgur.com/xE1dA.gif) This is what is happening to my motor. Any suggestions would help.",
"my motor. Any suggestions would help. 1. I have tried adjusting the trimpot.",
"the connector to match the one on the motherboard. 3. Anything else I",
"I have tried adjusting the trimpot. 2. Rewire the connector to match the",
"is what is happening to my motor. Any suggestions would help. 1. I",
"description here](https://i.stack.imgur.com/xE1dA.gif) This is what is happening to my motor. Any suggestions would",
"connector to match the one on the motherboard. 3. Anything else I found",
"would help. 1. I have tried adjusting the trimpot. 2. Rewire the connector",
"trimpot. 2. Rewire the connector to match the one on the motherboard. 3.",
"suggestions would help. 1. I have tried adjusting the trimpot. 2. Rewire the",
"to my motor. Any suggestions would help. 1. I have tried adjusting the",
"image description here](https://i.stack.imgur.com/xE1dA.gif) This is what is happening to my motor. Any suggestions",
"2. Rewire the connector to match the one on the motherboard. 3. Anything",
" This is what is happening to my motor. Any",
"help. 1. I have tried adjusting the trimpot. 2. Rewire the connector to",
"the one on the motherboard. 3. Anything else I found on the internet.",
"what is happening to my motor. Any suggestions would help. 1. I have",
"Any suggestions would help. 1. I have tried adjusting the trimpot. 2. Rewire",
"This is what is happening to my motor. Any suggestions would help. 1.",
"to match the one on the motherboard. 3. Anything else I found on",
"match the one on the motherboard. 3. Anything else I found on the",
"the trimpot. 2. Rewire the connector to match the one on the motherboard.",
"Rewire the connector to match the one on the motherboard. 3. Anything else",
"adjusting the trimpot. 2. Rewire the connector to match the one on the",
"have tried adjusting the trimpot. 2. Rewire the connector to match the one",
"is happening to my motor. Any suggestions would help. 1. I have tried",
"motor. Any suggestions would help. 1. I have tried adjusting the trimpot. 2.",
"tried adjusting the trimpot. 2. Rewire the connector to match the one on",
"1. I have tried adjusting the trimpot. 2. Rewire the connector to match"
] |
[
"to guessing). My question is, how far at 90\\* from a wall can",
"edges hanging out the side. I always worry, since it is printing in",
"print. But I was able to go, maybe 1mm(I am not to good",
"note. I am printing out things for people and some files have some",
"hanging out the side. I always worry, since it is printing in mid",
"people and some files have some edges hanging out the side. I always",
"just for people to make note. I am printing out things for people",
"it is necessary to have support? This would help me when slicing up",
"how far at 90\\* from a wall can a printer pull off before",
"question is, how far at 90\\* from a wall can a printer pull",
"a wall can a printer pull off before it is necessary to have",
"go, maybe 1mm(I am not to good with metric when it comes to",
"in more of a general sense than anything, just for people to make",
"this in more of a general sense than anything, just for people to",
"mid air, that it would screw up the print. But I was able",
"to good with metric when it comes to guessing). My question is, how",
"I would like to ask this in more of a general sense than",
"guessing). My question is, how far at 90\\* from a wall can a",
"up the print. But I was able to go, maybe 1mm(I am not",
"out the side. I always worry, since it is printing in mid air,",
"I always worry, since it is printing in mid air, that it would",
"a general sense than anything, just for people to make note. I am",
"is printing in mid air, that it would screw up the print. But",
"like to ask this in more of a general sense than anything, just",
"than anything, just for people to make note. I am printing out things",
"of a general sense than anything, just for people to make note. I",
"My question is, how far at 90\\* from a wall can a printer",
"it would screw up the print. But I was able to go, maybe",
"for people to make note. I am printing out things for people and",
"maybe 1mm(I am not to good with metric when it comes to guessing).",
"for people and some files have some edges hanging out the side. I",
"able to go, maybe 1mm(I am not to good with metric when it",
"comes to guessing). My question is, how far at 90\\* from a wall",
"in mid air, that it would screw up the print. But I was",
"would like to ask this in more of a general sense than anything,",
"the side. I always worry, since it is printing in mid air, that",
"metric when it comes to guessing). My question is, how far at 90\\*",
"with metric when it comes to guessing). My question is, how far at",
"since it is printing in mid air, that it would screw up the",
"some files have some edges hanging out the side. I always worry, since",
"that it would screw up the print. But I was able to go,",
"out things for people and some files have some edges hanging out the",
"to ask this in more of a general sense than anything, just for",
"people to make note. I am printing out things for people and some",
"But I was able to go, maybe 1mm(I am not to good with",
"printing out things for people and some files have some edges hanging out",
"1mm(I am not to good with metric when it comes to guessing). My",
"far at 90\\* from a wall can a printer pull off before it",
"is, how far at 90\\* from a wall can a printer pull off",
"files have some edges hanging out the side. I always worry, since it",
"screw up the print. But I was able to go, maybe 1mm(I am",
"air, that it would screw up the print. But I was able to",
"was able to go, maybe 1mm(I am not to good with metric when",
"make note. I am printing out things for people and some files have",
"general sense than anything, just for people to make note. I am printing",
"before it is necessary to have support? This would help me when slicing",
"it is printing in mid air, that it would screw up the print.",
"side. I always worry, since it is printing in mid air, that it",
"printing in mid air, that it would screw up the print. But I",
"when it comes to guessing). My question is, how far at 90\\* from",
"have some edges hanging out the side. I always worry, since it is",
"wall can a printer pull off before it is necessary to have support?",
"not to good with metric when it comes to guessing). My question is,",
"printer pull off before it is necessary to have support? This would help",
"more of a general sense than anything, just for people to make note.",
"it comes to guessing). My question is, how far at 90\\* from a",
"is necessary to have support? This would help me when slicing up files.",
"some edges hanging out the side. I always worry, since it is printing",
"a printer pull off before it is necessary to have support? This would",
"good with metric when it comes to guessing). My question is, how far",
"sense than anything, just for people to make note. I am printing out",
"the print. But I was able to go, maybe 1mm(I am not to",
"and some files have some edges hanging out the side. I always worry,",
"am printing out things for people and some files have some edges hanging",
"90\\* from a wall can a printer pull off before it is necessary",
"I am printing out things for people and some files have some edges",
"off before it is necessary to have support? This would help me when",
"always worry, since it is printing in mid air, that it would screw",
"pull off before it is necessary to have support? This would help me",
"at 90\\* from a wall can a printer pull off before it is",
"can a printer pull off before it is necessary to have support? This",
"I was able to go, maybe 1mm(I am not to good with metric",
"from a wall can a printer pull off before it is necessary to",
"am not to good with metric when it comes to guessing). My question",
"ask this in more of a general sense than anything, just for people",
"to go, maybe 1mm(I am not to good with metric when it comes",
"worry, since it is printing in mid air, that it would screw up",
"things for people and some files have some edges hanging out the side.",
"to make note. I am printing out things for people and some files",
"anything, just for people to make note. I am printing out things for",
"would screw up the print. But I was able to go, maybe 1mm(I"
] |
[
"the glass, with blue painters tape it sticks even too much so I'll",
"a 0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end",
"totally) was to bump up the layer thickness to 0.3mm [Edit 2] Finally",
"and my white eSun. **What's my problem?** Thank you all! [Edit] Tried about",
"borosilicate glass bed on top of the heat bed which ensures a perfect",
"perfectly well, but quickly I got some problems with my first layer. It's",
"it works even amazingly well, I just have to print something really big",
"my black eSun and my white eSun. **What's my problem?** Thank you all!",
"1 week old eSun filament, a E3D V6 Hotend 1.75mm on my scratch",
"but didn't go away totally) was to bump up the layer thickness to",
"around z delta, removing linear advance, radically lowering speed) but the only thing",
"is no longer a problem. I also lowered the first layer speed to",
"I got some problems with my first layer. It's like droplets are forming",
"get rid of those pesky 'drops'. **As the defect is quite stable and",
"the defect is quite stable and quite recognizable and it happens all the",
"put blue tape on the glass because the first layer was tricky. This",
"moving around z delta, removing linear advance, radically lowering speed) but the only",
"2] Finally it seems it was, as it usually is, a conjuncture of",
"the first layer didn't stick easily directly onto the glass, with blue painters",
"was quite reduced but didn't go away totally) was to bump up the",
"image description here](https://i.stack.imgur.com/qgPyl.jpg)](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay but I'd like",
"eSun and my white eSun. **What's my problem?** Thank you all! [Edit] Tried",
"a colder second (and on) layer * Maybe the speed was a bit",
"I fixed this by installing a borosilicate glass bed on top of the",
"4mm I had previously added) to make this function. I think it is",
"first layer. It's like droplets are forming on the surface (finished item +",
"go away totally) was to bump up the layer thickness to 0.3mm [Edit",
"'drops'. **As the defect is quite stable and quite recognizable and it happens",
"height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer, then lower a",
"old eSun filament, a E3D V6 Hotend 1.75mm on my scratch CoreXY printer,",
"not perfectly flat * The heatbed moved/bended when going from a hot first",
"0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for",
"glass, with blue painters tape it sticks even too much so I'll try",
"as it usually is, a conjuncture of several problems that I will list",
"me) okay but I'd like to get rid of those pesky 'drops'. **As",
"it's enough for now. I'm thinking about how to make the glass conductive,",
"problems though so it might be a path to try if you run",
"* The bed was not perfectly flat * The heatbed moved/bended when going",
"not perfectly flat), but it's enough for now. I'm thinking about how to",
"up the layer thickness to 0.3mm [Edit 2] Finally it seems it was,",
"and for starters it worked perfectly well, but quickly I got some problems",
"(see above). Heatbed temperature for first layer: 70°C Extruder temperature anywhere from 190°C",
"first layer to a colder second (and on) layer * Maybe the speed",
"similar problems. And now it seems that it works even amazingly well, I",
"the heatbed under the glass (which is not perfectly flat), but it's enough",
"list here: * The bed was not perfectly flat * The heatbed moved/bended",
"like aluminium or something, but that's for another day/post. I also put blue",
"Worked perfectly well with my black eSun and my white eSun. **What's my",
"for now. I'm thinking about how to make the glass conductive, like aluminium",
"use Blue-painter tape. Worked perfectly well with my black eSun and my white",
"to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly well",
"perfectly well with my black eSun and my white eSun. **What's my problem?**",
"layer didn't stick easily directly onto the glass, with blue painters tape it",
"doesn't do its job that well (see above). Heatbed temperature for first layer:",
"tape it sticks even too much so I'll try higher speeds. It did",
"quite low). The print is done using a 0.4mm diameter nozzle at 0.2mm",
"layer * Maybe the speed was a bit high for the first layer",
"problems. And now it seems that it works even amazingly well, I just",
"to see! ---------------Old: Moving z up made spaghetti :-) and different temperatures made",
"0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer, then lower",
"undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay but",
"with my black eSun and my white eSun. **What's my problem?** Thank you",
"of those pesky 'drops'. **As the defect is quite stable and quite recognizable",
"it is no longer a problem. I also lowered the first layer speed",
"I'm thinking about how to make the glass conductive, like aluminium or something,",
"black eSun and my white eSun. **What's my problem?** Thank you all! [Edit]",
"or it is no longer a problem. I also lowered the first layer",
"day/post. I also put blue tape on the glass because the first layer",
"by installing a borosilicate glass bed on top of the heat bed which",
"than me knows what's going on!** Info: I'm using a 1 week old",
"under the glass (which is not perfectly flat), but it's enough for now.",
"for first layer: 70°C Extruder temperature anywhere from 190°C to 220°C works fine,",
"easily directly onto the glass, with blue painters tape it sticks even too",
"Info: I'm using a 1 week old eSun filament, a E3D V6 Hotend",
"(for me) okay but I'd like to get rid of those pesky 'drops'.",
"was, as it usually is, a conjuncture of several problems that I will",
"even amazingly well, I just have to print something really big to see!",
"got some problems with my first layer. It's like droplets are forming on",
"the glass because the first layer was tricky. This might be because the",
"big to see! ---------------Old: Moving z up made spaghetti :-) and different temperatures",
"painters tape it sticks even too much so I'll try higher speeds. It",
"have to print something really big to see! ---------------Old: Moving z up made",
"usually is, a conjuncture of several problems that I will list here: *",
"heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly well with my",
"white eSun. **What's my problem?** Thank you all! [Edit] Tried about everything (more",
"time, I bet somebody more experienced than me knows what's going on!** Info:",
"happens all the time, I bet somebody more experienced than me knows what's",
"with blue painters tape it sticks even too much so I'll try higher",
"made spaghetti :-) and different temperatures made quite extreme warping: [![enter image description",
"filament and for starters it worked perfectly well, but quickly I got some",
"those pesky 'drops'. **As the defect is quite stable and quite recognizable and",
"removing linear advance, radically lowering speed) but the only thing that worked about",
"214°C(417°C) hot-end for first layer, then lower a bit to 40°C(104°F) heat-bed and",
"my scratch CoreXY printer, short Bowden direct drive, Repetier, Marlin, Linear advance (M900",
"problem?** Thank you all! [Edit] Tried about everything (more temp, less temp, fan",
"well, I just have to print something really big to see! ---------------Old: Moving",
"thing that worked about okay (problem was quite reduced but didn't go away",
"also lowered the first layer speed to 20mm/s because the first layer didn't",
"the first layer was tricky. This might be because the inductive sensor doesn't",
"stable and quite recognizable and it happens all the time, I bet somebody",
"temp, fan on item, more / less bed temp, underextrude, moving around z",
"Extruder temperature anywhere from 190°C to 220°C works fine, that was not the",
"if you run into similar problems. And now it seems that it works",
"make this function. I think it is not as good as it can",
"another day/post. I also put blue tape on the glass because the first",
"to a colder second (and on) layer * Maybe the speed was a",
"or something, but that's for another day/post. I also put blue tape on",
"defect is quite stable and quite recognizable and it happens all the time,",
"flat), but it's enough for now. I'm thinking about how to make the",
"like droplets are forming on the surface (finished item + 3 undersides): [](https://i.stack.imgur.com/eV7UJ.jpg) [![enter image",
"perfect flatness. I had to change my inductive sensor to an 8mm one",
"heat bed which ensures a perfect flatness. I had to change my inductive",
"directly onto the glass, with blue painters tape it sticks even too much",
"be because the inductive sensor doesn't do its job that well (see above).",
"to bump up the layer thickness to 0.3mm [Edit 2] Finally it seems",
"this function. I think it is not as good as it can be",
"part is (for me) okay but I'd like to get rid of those",
"be as it detects the heatbed under the glass (which is not perfectly",
"low). The print is done using a 0.4mm diameter nozzle at 0.2mm height",
"radically lowering speed) but the only thing that worked about okay (problem was",
"quickly I got some problems with my first layer. It's like droplets are",
"all the time, I bet somebody more experienced than me knows what's going",
"for another day/post. I also put blue tape on the glass because the",
"to try if you run into similar problems. And now it seems that",
"40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly well with",
"blue painters tape it sticks even too much so I'll try higher speeds.",
"a perfect flatness. I had to change my inductive sensor to an 8mm",
"and 214°C(417°C) hot-end for first layer, then lower a bit to 40°C(104°F) heat-bed",
"recognizable and it happens all the time, I bet somebody more experienced than",
"first layer: 70°C Extruder temperature anywhere from 190°C to 220°C works fine, that",
"but that's for another day/post. I also put blue tape on the glass",
"longer a problem. I also lowered the first layer speed to 20mm/s because",
"from 190°C to 220°C works fine, that was not the problem, or it",
"**What's my problem?** Thank you all! [Edit] Tried about everything (more temp, less",
"conjuncture of several problems that I will list here: * The bed was",
"only thing that worked about okay (problem was quite reduced but didn't go",
"perfectly flat * The heatbed moved/bended when going from a hot first layer",
"layer thickness to 0.3mm [Edit 2] Finally it seems it was, as it",
"I had previously added) to make this function. I think it is not",
"K60 so quite low). The print is done using a 0.4mm diameter nozzle",
"sticks even too much so I'll try higher speeds. It did mitigate problems",
"you run into similar problems. And now it seems that it works even",
"several problems that I will list here: * The bed was not perfectly",
"seems it was, as it usually is, a conjuncture of several problems that",
"moved/bended when going from a hot first layer to a colder second (and",
"really big to see! ---------------Old: Moving z up made spaghetti :-) and different",
"forming on the surface (finished item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg)",
"bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly",
"now. I'm thinking about how to make the glass conductive, like aluminium or",
"I recently changed filament and for starters it worked perfectly well, but quickly",
"E3D V6 Hotend 1.75mm on my scratch CoreXY printer, short Bowden direct drive,",
"layer to a colder second (and on) layer * Maybe the speed was",
"Linear advance (M900 K60 so quite low). The print is done using a",
"done using a 0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed and",
"the glass conductive, like aluminium or something, but that's for another day/post. I",
"heatbed under the glass (which is not perfectly flat), but it's enough for",
"The heatbed moved/bended when going from a hot first layer to a colder",
"tape. Worked perfectly well with my black eSun and my white eSun. **What's",
"Hotend 1.75mm on my scratch CoreXY printer, short Bowden direct drive, Repetier, Marlin,",
"I had to change my inductive sensor to an 8mm one (insteéad of",
"previously added) to make this function. I think it is not as good",
"less temp, fan on item, more / less bed temp, underextrude, moving around",
"a borosilicate glass bed on top of the heat bed which ensures a",
"inductive sensor doesn't do its job that well (see above). Heatbed temperature for",
"much so I'll try higher speeds. It did mitigate problems though so it",
"* Maybe the speed was a bit high for the first layer (25mm/s)",
"filament, a E3D V6 Hotend 1.75mm on my scratch CoreXY printer, short Bowden",
"item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for",
"aluminium or something, but that's for another day/post. I also put blue tape",
"well with my black eSun and my white eSun. **What's my problem?** Thank",
"hot-end. I use Blue-painter tape. Worked perfectly well with my black eSun and",
"item, more / less bed temp, underextrude, moving around z delta, removing linear",
"it is not as good as it can be as it detects the",
"a 1 week old eSun filament, a E3D V6 Hotend 1.75mm on my",
"of the 4mm I had previously added) to make this function. I think",
"and 211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly well with my black",
"(insteéad of the 4mm I had previously added) to make this function. I",
"installing a borosilicate glass bed on top of the heat bed which ensures",
"but quickly I got some problems with my first layer. It's like droplets",
"[](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay but I'd",
"glass because the first layer was tricky. This might be because the inductive",
"I'd like to get rid of those pesky 'drops'. **As the defect is",
"temperatures made quite extreme warping: [](https://i.stack.imgur.com/eV7UJ.jpg) [](https://i.stack.imgur.com/7VeCT.jpg)",
"it happens all the time, I bet somebody more experienced than me knows",
"inductive sensor to an 8mm one (insteéad of the 4mm I had previously",
"perfectly flat), but it's enough for now. I'm thinking about how to make",
"anywhere from 190°C to 220°C works fine, that was not the problem, or",
"here](https://i.stack.imgur.com/qgPyl.jpg)](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay but I'd like to get",
"how to make the glass conductive, like aluminium or something, but that's for",
"it detects the heatbed under the glass (which is not perfectly flat), but",
"try higher speeds. It did mitigate problems though so it might be a",
"about how to make the glass conductive, like aluminium or something, but that's",
"might be because the inductive sensor doesn't do its job that well (see",
"like to get rid of those pesky 'drops'. **As the defect is quite",
"mitigate problems though so it might be a path to try if you",
"first layer, then lower a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I",
"the first layer (25mm/s) I fixed this by installing a borosilicate glass bed",
"printer, short Bowden direct drive, Repetier, Marlin, Linear advance (M900 K60 so quite",
"less bed temp, underextrude, moving around z delta, removing linear advance, radically lowering",
"conductive, like aluminium or something, but that's for another day/post. I also put",
"that it works even amazingly well, I just have to print something really",
"diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first",
"as it can be as it detects the heatbed under the glass (which",
"is not perfectly flat), but it's enough for now. I'm thinking about how",
"this by installing a borosilicate glass bed on top of the heat bed",
"to make this function. I think it is not as good as it",
"8mm one (insteéad of the 4mm I had previously added) to make this",
"underextrude, moving around z delta, removing linear advance, radically lowering speed) but the",
"quite reduced but didn't go away totally) was to bump up the layer",
"that's for another day/post. I also put blue tape on the glass because",
"the layer thickness to 0.3mm [Edit 2] Finally it seems it was, as",
"colder second (and on) layer * Maybe the speed was a bit high",
"because the inductive sensor doesn't do its job that well (see above). Heatbed",
"190°C to 220°C works fine, that was not the problem, or it is",
"temperature for first layer: 70°C Extruder temperature anywhere from 190°C to 220°C works",
"Thank you all! [Edit] Tried about everything (more temp, less temp, fan on",
"the only thing that worked about okay (problem was quite reduced but didn't",
"an 8mm one (insteéad of the 4mm I had previously added) to make",
"well (see above). Heatbed temperature for first layer: 70°C Extruder temperature anywhere from",
"onto the glass, with blue painters tape it sticks even too much so",
"I will list here: * The bed was not perfectly flat * The",
"one (insteéad of the 4mm I had previously added) to make this function.",
"didn't stick easily directly onto the glass, with blue painters tape it sticks",
"all! [Edit] Tried about everything (more temp, less temp, fan on item, more",
"on) layer * Maybe the speed was a bit high for the first",
"to get rid of those pesky 'drops'. **As the defect is quite stable",
"and quite recognizable and it happens all the time, I bet somebody more",
"lowered the first layer speed to 20mm/s because the first layer didn't stick",
"220°C works fine, that was not the problem, or it is no longer",
"going from a hot first layer to a colder second (and on) layer",
"on my scratch CoreXY printer, short Bowden direct drive, Repetier, Marlin, Linear advance",
"it might be a path to try if you run into similar problems.",
"here: * The bed was not perfectly flat * The heatbed moved/bended when",
"bed temp, underextrude, moving around z delta, removing linear advance, radically lowering speed)",
"---------------Old: Moving z up made spaghetti :-) and different temperatures made quite extreme",
"(problem was quite reduced but didn't go away totally) was to bump up",
"but the only thing that worked about okay (problem was quite reduced but",
"of the heat bed which ensures a perfect flatness. I had to change",
"The print is done using a 0.4mm diameter nozzle at 0.2mm height at:",
"fine, that was not the problem, or it is no longer a problem.",
"week old eSun filament, a E3D V6 Hotend 1.75mm on my scratch CoreXY",
"which ensures a perfect flatness. I had to change my inductive sensor to",
"1.75mm on my scratch CoreXY printer, short Bowden direct drive, Repetier, Marlin, Linear",
"my problem?** Thank you all! [Edit] Tried about everything (more temp, less temp,",
"as it detects the heatbed under the glass (which is not perfectly flat),",
"**As the defect is quite stable and quite recognizable and it happens all",
"more / less bed temp, underextrude, moving around z delta, removing linear advance,",
"my first layer. It's like droplets are forming on the surface (finished item",
"I'll try higher speeds. It did mitigate problems though so it might be",
"a bit high for the first layer (25mm/s) I fixed this by installing",
"the surface (finished item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final",
"the heat bed which ensures a perfect flatness. I had to change my",
"reduced but didn't go away totally) was to bump up the layer thickness",
"not the problem, or it is no longer a problem. I also lowered",
"pesky 'drops'. **As the defect is quite stable and quite recognizable and it",
"about okay (problem was quite reduced but didn't go away totally) was to",
"And now it seems that it works even amazingly well, I just have",
"thickness to 0.3mm [Edit 2] Finally it seems it was, as it usually",
"heat-bed and 214°C(417°C) hot-end for first layer, then lower a bit to 40°C(104°F)",
"as good as it can be as it detects the heatbed under the",
"seems that it works even amazingly well, I just have to print something",
"final part is (for me) okay but I'd like to get rid of",
"at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer, then",
"was to bump up the layer thickness to 0.3mm [Edit 2] Finally it",
"higher speeds. It did mitigate problems though so it might be a path",
"quite stable and quite recognizable and it happens all the time, I bet",
":-) and different temperatures made quite extreme warping: [](https://i.stack.imgur.com/eV7UJ.jpg) [](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay",
"It did mitigate problems though so it might be a path to try",
"up made spaghetti :-) and different temperatures made quite extreme warping: [![enter image",
"(and on) layer * Maybe the speed was a bit high for the",
"everything (more temp, less temp, fan on item, more / less bed temp,",
"linear advance, radically lowering speed) but the only thing that worked about okay",
"my white eSun. **What's my problem?** Thank you all! [Edit] Tried about everything",
"* The heatbed moved/bended when going from a hot first layer to a",
"to 0.3mm [Edit 2] Finally it seems it was, as it usually is,",
"z delta, removing linear advance, radically lowering speed) but the only thing that",
"glass (which is not perfectly flat), but it's enough for now. I'm thinking",
"think it is not as good as it can be as it detects",
"when going from a hot first layer to a colder second (and on)",
"that worked about okay (problem was quite reduced but didn't go away totally)",
"it usually is, a conjuncture of several problems that I will list here:",
"0.3mm [Edit 2] Finally it seems it was, as it usually is, a",
"spaghetti :-) and different temperatures made quite extreme warping: [](https://i.stack.imgur.com/eV7UJ.jpg)",
"Bowden direct drive, Repetier, Marlin, Linear advance (M900 K60 so quite low). The",
"enough for now. I'm thinking about how to make the glass conductive, like",
"drive, Repetier, Marlin, Linear advance (M900 K60 so quite low). The print is",
"it was, as it usually is, a conjuncture of several problems that I",
"was tricky. This might be because the inductive sensor doesn't do its job",
"speeds. It did mitigate problems though so it might be a path to",
"detects the heatbed under the glass (which is not perfectly flat), but it's",
"ensures a perfect flatness. I had to change my inductive sensor to an",
"try if you run into similar problems. And now it seems that it",
"into similar problems. And now it seems that it works even amazingly well,",
"different temperatures made quite extreme warping: [](https://i.stack.imgur.com/eV7UJ.jpg) [![enter image description",
"speed) but the only thing that worked about okay (problem was quite reduced",
"the first layer speed to 20mm/s because the first layer didn't stick easily",
"to change my inductive sensor to an 8mm one (insteéad of the 4mm",
"rid of those pesky 'drops'. **As the defect is quite stable and quite",
"bed was not perfectly flat * The heatbed moved/bended when going from a",
"heatbed moved/bended when going from a hot first layer to a colder second",
"the problem, or it is no longer a problem. I also lowered the",
"layer (25mm/s) I fixed this by installing a borosilicate glass bed on top",
"is quite stable and quite recognizable and it happens all the time, I",
"to an 8mm one (insteéad of the 4mm I had previously added) to",
"50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer, then lower a bit to",
"This might be because the inductive sensor doesn't do its job that well",
"hot first layer to a colder second (and on) layer * Maybe the",
"is done using a 0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed",
"worked about okay (problem was quite reduced but didn't go away totally) was",
"tricky. This might be because the inductive sensor doesn't do its job that",
"even too much so I'll try higher speeds. It did mitigate problems though",
"away totally) was to bump up the layer thickness to 0.3mm [Edit 2]",
"scratch CoreXY printer, short Bowden direct drive, Repetier, Marlin, Linear advance (M900 K60",
"20mm/s because the first layer didn't stick easily directly onto the glass, with",
"it seems that it works even amazingly well, I just have to print",
"layer, then lower a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use",
"that well (see above). Heatbed temperature for first layer: 70°C Extruder temperature anywhere",
"job that well (see above). Heatbed temperature for first layer: 70°C Extruder temperature",
"about everything (more temp, less temp, fan on item, more / less bed",
"CoreXY printer, short Bowden direct drive, Repetier, Marlin, Linear advance (M900 K60 so",
"using a 1 week old eSun filament, a E3D V6 Hotend 1.75mm on",
"on the glass because the first layer was tricky. This might be because",
"its job that well (see above). Heatbed temperature for first layer: 70°C Extruder",
"changed filament and for starters it worked perfectly well, but quickly I got",
"second (and on) layer * Maybe the speed was a bit high for",
"Maybe the speed was a bit high for the first layer (25mm/s) I",
"that was not the problem, or it is no longer a problem. I",
"print something really big to see! ---------------Old: Moving z up made spaghetti :-)",
"Moving z up made spaghetti :-) and different temperatures made quite extreme warping:",
"so quite low). The print is done using a 0.4mm diameter nozzle at",
"direct drive, Repetier, Marlin, Linear advance (M900 K60 so quite low). The print",
"temperature anywhere from 190°C to 220°C works fine, that was not the problem,",
"for the first layer (25mm/s) I fixed this by installing a borosilicate glass",
"using a 0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C)",
"problem. I also lowered the first layer speed to 20mm/s because the first",
"+ 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me)",
"Repetier, Marlin, Linear advance (M900 K60 so quite low). The print is done",
"no longer a problem. I also lowered the first layer speed to 20mm/s",
"first layer didn't stick easily directly onto the glass, with blue painters tape",
"on top of the heat bed which ensures a perfect flatness. I had",
"path to try if you run into similar problems. And now it seems",
"be a path to try if you run into similar problems. And now",
"to print something really big to see! ---------------Old: Moving z up made spaghetti",
"it can be as it detects the heatbed under the glass (which is",
"speed was a bit high for the first layer (25mm/s) I fixed this",
"some problems with my first layer. It's like droplets are forming on the",
"because the first layer didn't stick easily directly onto the glass, with blue",
"layer: 70°C Extruder temperature anywhere from 190°C to 220°C works fine, that was",
"a hot first layer to a colder second (and on) layer * Maybe",
"layer. It's like droplets are forming on the surface (finished item + 3",
"(finished item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final part is",
"change my inductive sensor to an 8mm one (insteéad of the 4mm I",
"for starters it worked perfectly well, but quickly I got some problems with",
"experienced than me knows what's going on!** Info: I'm using a 1 week",
"the 4mm I had previously added) to make this function. I think it",
"works fine, that was not the problem, or it is no longer a",
"had previously added) to make this function. I think it is not as",
"too much so I'll try higher speeds. It did mitigate problems though so",
"The final part is (for me) okay but I'd like to get rid",
"not as good as it can be as it detects the heatbed under",
"I just have to print something really big to see! ---------------Old: Moving z",
"so it might be a path to try if you run into similar",
"top of the heat bed which ensures a perfect flatness. I had to",
"(which is not perfectly flat), but it's enough for now. I'm thinking about",
"though so it might be a path to try if you run into",
"[Edit 2] Finally it seems it was, as it usually is, a conjuncture",
"starters it worked perfectly well, but quickly I got some problems with my",
"z up made spaghetti :-) and different temperatures made quite extreme warping: [![enter",
"bet somebody more experienced than me knows what's going on!** Info: I'm using",
"first layer speed to 20mm/s because the first layer didn't stick easily directly",
"droplets are forming on the surface (finished item + 3 undersides): [![enter image",
"It's like droplets are forming on the surface (finished item + 3 undersides):",
"recently changed filament and for starters it worked perfectly well, but quickly I",
"the time, I bet somebody more experienced than me knows what's going on!**",
"more experienced than me knows what's going on!** Info: I'm using a 1",
"Finally it seems it was, as it usually is, a conjuncture of several",
"[Edit] Tried about everything (more temp, less temp, fan on item, more /",
"hot-end for first layer, then lower a bit to 40°C(104°F) heat-bed and 211°C(412°F)",
"a problem. I also lowered the first layer speed to 20mm/s because the",
"layer was tricky. This might be because the inductive sensor doesn't do its",
"going on!** Info: I'm using a 1 week old eSun filament, a E3D",
"problems that I will list here: * The bed was not perfectly flat",
"me knows what's going on!** Info: I'm using a 1 week old eSun",
"run into similar problems. And now it seems that it works even amazingly",
"delta, removing linear advance, radically lowering speed) but the only thing that worked",
"works even amazingly well, I just have to print something really big to",
"sensor doesn't do its job that well (see above). Heatbed temperature for first",
"bed which ensures a perfect flatness. I had to change my inductive sensor",
"first layer was tricky. This might be because the inductive sensor doesn't do",
"I'm using a 1 week old eSun filament, a E3D V6 Hotend 1.75mm",
"something really big to see! ---------------Old: Moving z up made spaghetti :-) and",
"but it's enough for now. I'm thinking about how to make the glass",
"speed to 20mm/s because the first layer didn't stick easily directly onto the",
"so I'll try higher speeds. It did mitigate problems though so it might",
"okay (problem was quite reduced but didn't go away totally) was to bump",
"fixed this by installing a borosilicate glass bed on top of the heat",
"bed on top of the heat bed which ensures a perfect flatness. I",
"surface (finished item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The final part",
"(more temp, less temp, fan on item, more / less bed temp, underextrude,",
"temp, less temp, fan on item, more / less bed temp, underextrude, moving",
"the glass (which is not perfectly flat), but it's enough for now. I'm",
"I bet somebody more experienced than me knows what's going on!** Info: I'm",
"well, but quickly I got some problems with my first layer. It's like",
"Blue-painter tape. Worked perfectly well with my black eSun and my white eSun.",
"V6 Hotend 1.75mm on my scratch CoreXY printer, short Bowden direct drive, Repetier,",
"211°C(412°F) hot-end. I use Blue-painter tape. Worked perfectly well with my black eSun",
"bit high for the first layer (25mm/s) I fixed this by installing a",
"good as it can be as it detects the heatbed under the glass",
"was not perfectly flat * The heatbed moved/bended when going from a hot",
"glass bed on top of the heat bed which ensures a perfect flatness.",
"can be as it detects the heatbed under the glass (which is not",
"/ less bed temp, underextrude, moving around z delta, removing linear advance, radically",
"problem, or it is no longer a problem. I also lowered the first",
"was not the problem, or it is no longer a problem. I also",
"to 20mm/s because the first layer didn't stick easily directly onto the glass,",
"I think it is not as good as it can be as it",
"eSun. **What's my problem?** Thank you all! [Edit] Tried about everything (more temp,",
"might be a path to try if you run into similar problems. And",
"a path to try if you run into similar problems. And now it",
"had to change my inductive sensor to an 8mm one (insteéad of the",
"do its job that well (see above). Heatbed temperature for first layer: 70°C",
"first layer (25mm/s) I fixed this by installing a borosilicate glass bed on",
"because the first layer was tricky. This might be because the inductive sensor",
"I also lowered the first layer speed to 20mm/s because the first layer",
"to make the glass conductive, like aluminium or something, but that's for another",
"problems with my first layer. It's like droplets are forming on the surface",
"print is done using a 0.4mm diameter nozzle at 0.2mm height at: 50°C(122°F)",
"advance (M900 K60 so quite low). The print is done using a 0.4mm",
"with my first layer. It's like droplets are forming on the surface (finished",
"70°C Extruder temperature anywhere from 190°C to 220°C works fine, that was not",
"did mitigate problems though so it might be a path to try if",
"on the surface (finished item + 3 undersides): [](https://i.stack.imgur.com/qgPyl.jpg) The",
"just have to print something really big to see! ---------------Old: Moving z up",
"and it happens all the time, I bet somebody more experienced than me",
"thinking about how to make the glass conductive, like aluminium or something, but",
"on!** Info: I'm using a 1 week old eSun filament, a E3D V6",
"somebody more experienced than me knows what's going on!** Info: I'm using a",
"I also put blue tape on the glass because the first layer was",
"advance, radically lowering speed) but the only thing that worked about okay (problem",
"lower a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape.",
"see! ---------------Old: Moving z up made spaghetti :-) and different temperatures made quite",
"you all! [Edit] Tried about everything (more temp, less temp, fan on item,",
"okay but I'd like to get rid of those pesky 'drops'. **As the",
"a E3D V6 Hotend 1.75mm on my scratch CoreXY printer, short Bowden direct",
"a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter tape. Worked",
"at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer, then lower a bit",
"from a hot first layer to a colder second (and on) layer *",
"temp, underextrude, moving around z delta, removing linear advance, radically lowering speed) but",
"nozzle at 0.2mm height at: 50°C(122°F) heat-bed and 214°C(417°C) hot-end for first layer,",
"Marlin, Linear advance (M900 K60 so quite low). The print is done using",
"eSun filament, a E3D V6 Hotend 1.75mm on my scratch CoreXY printer, short",
"for first layer, then lower a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end.",
"the speed was a bit high for the first layer (25mm/s) I fixed",
"layer speed to 20mm/s because the first layer didn't stick easily directly onto",
"The bed was not perfectly flat * The heatbed moved/bended when going from",
"on item, more / less bed temp, underextrude, moving around z delta, removing",
"glass conductive, like aluminium or something, but that's for another day/post. I also",
"bump up the layer thickness to 0.3mm [Edit 2] Finally it seems it",
"I use Blue-painter tape. Worked perfectly well with my black eSun and my",
"above). Heatbed temperature for first layer: 70°C Extruder temperature anywhere from 190°C to",
"is not as good as it can be as it detects the heatbed",
"that I will list here: * The bed was not perfectly flat *",
"it worked perfectly well, but quickly I got some problems with my first",
"amazingly well, I just have to print something really big to see! ---------------Old:",
"a conjuncture of several problems that I will list here: * The bed",
"then lower a bit to 40°C(104°F) heat-bed and 211°C(412°F) hot-end. I use Blue-painter",
"it sticks even too much so I'll try higher speeds. It did mitigate",
"flatness. I had to change my inductive sensor to an 8mm one (insteéad",
"worked perfectly well, but quickly I got some problems with my first layer.",
"didn't go away totally) was to bump up the layer thickness to 0.3mm",
"what's going on!** Info: I'm using a 1 week old eSun filament, a",
"tape on the glass because the first layer was tricky. This might be",
"is, a conjuncture of several problems that I will list here: * The",
"description here](https://i.stack.imgur.com/qgPyl.jpg)](https://i.stack.imgur.com/qgPyl.jpg) The final part is (for me) okay but I'd like to",
"(25mm/s) I fixed this by installing a borosilicate glass bed on top of",
"the inductive sensor doesn't do its job that well (see above). Heatbed temperature"
] |
[
"settings\" ok echo:Unknown command: \"okechecho\" ok ``` The \"SD init fail\" line and",
"first attempt to get access to low-level printer interface looked like that: ```",
"(mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),",
"``` First it was fine: i've entered g-code, printer executed it and returned",
"and everything after it appears when sensor data appears on the LCD, there's",
"line and everything after it appears when sensor data appears on the LCD,",
"G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access",
"output anything and printer LCD displayed garbage in the status line after I",
"it appears when sensor data appears on the LCD, there's a delay before",
"XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown",
"LCD, there's a delay before that during which the LCD is empty. If",
"2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per",
"at all. The interesting part is that Cura \"Monitor\" tab can actually manipulate",
"entered g-code, printer executed it and returned an ok message into my terminal.",
"ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s),",
"segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E",
"whole process, but now `tail -f` didn't output anything and printer LCD displayed",
"cat > /dev/ttyACM0 ``` First it was fine: i've entered g-code, printer executed",
"init failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\"",
"\"SD init fail\" line and everything after it appears when sensor data appears",
"and printer LCD displayed garbage in the status line after I ran the",
"all. The interesting part is that Cura \"Monitor\" tab can actually manipulate the",
"during which the LCD is empty. If you send commands to printer using",
"garbage in the status line after I ran the command. I've also noticed",
"to try moving this thing from terminal. [How to directly send G-code to",
"command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z",
"printer executed it and returned an ok message into my terminal. Then i've",
"ran the command. I've also noticed that printer controller reboots every time the",
"echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00",
"time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk",
"command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok ``` The \"SD init fail\"",
"(mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown command:",
"``` start echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04 | Author: (none,",
"appears on the LCD, there's a delay before that during which the LCD",
"B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum",
"`tail -f` didn't output anything and printer LCD displayed garbage in the status",
"stitched together and with marlin firmware. I've used accepted answer from here to",
"unknown, got it as present, probably something generic cartesian on arduino mega and",
"ready\" as well: ``` start echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04",
"Default Settings Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum",
"\"okechecho\" ok ``` The \"SD init fail\" line and everything after it appears",
"reboot) - or doesn't execute at all. The interesting part is that Cura",
"is a bit weird too - and there's garbage in the status line",
"delay before that during which the LCD is empty. If you send commands",
"can print things in general - but i want to be able to",
"X10\" > /dev/ttyACM0`, it executes them only on next serial port accessing (and",
"worked well. The output of `cat /dev/ttyACM0` after baud setting is a bit",
"everything worked well. The output of `cat /dev/ttyACM0` after baud setting is a",
"The output of `cat /dev/ttyACM0` after baud setting is a bit weird too",
"status line after I ran the command. I've also noticed that printer controller",
"an ok message into my terminal. Then i've turned the printer off and",
"<> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it",
"printer using something like `echo \"G0 X10\" > /dev/ttyACM0`, it executes them only",
"M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100",
"E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate",
"\"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo: Last Updated: May 20 2017",
"i've turned the printer off and on again and repeated the whole process,",
"them only on next serial port accessing (and therefore reboot) - or doesn't",
"Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration:",
"weird too - and there's garbage in the status line instead of standard",
"X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000",
"there's garbage in the status line instead of standard \"%printername% ready\" as well:",
"every time the serial port is accessed, not sure if it happened in",
"\"Monitor\" tab can actually manipulate the caret and the Cura itself can print",
"\"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s),",
"command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command: \" (none,",
"PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00",
"/dev/ttyACM0` after baud setting is a bit weird too - and there's garbage",
"Settings Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates",
"is that Cura \"Monitor\" tab can actually manipulate the caret and the Cura",
"Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum",
"doesn't execute at all. The interesting part is that Cura \"Monitor\" tab can",
"firmware. I've used accepted answer from here to try moving this thing from",
"time when everything worked well. The output of `cat /dev/ttyACM0` after baud setting",
"\"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY",
"output of `cat /dev/ttyACM0` after baud setting is a bit weird too -",
"First it was fine: i've entered g-code, printer executed it and returned an",
"M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum",
"the LCD, there's a delay before that during which the LCD is empty.",
"tab can actually manipulate the caret and the Cura itself can print things",
"echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD",
"echo:Unknown command: \"okechecho\" ok ``` The \"SD init fail\" line and everything after",
"(mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID",
"E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301",
"E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own",
"the printer is unknown, got it as present, probably something generic cartesian on",
"- or doesn't execute at all. The interesting part is that Cura \"Monitor\"",
"moving this thing from terminal. [How to directly send G-code to printer from",
"Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command:",
"port accessing (and therefore reboot) - or doesn't execute at all. The interesting",
"in the status line after I ran the command. I've also noticed that",
"thing from terminal. [How to directly send G-code to printer from a Linux",
"-f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it was fine: i've entered",
"reboots every time the serial port is accessed, not sure if it happened",
"`echo \"G0 X10\" > /dev/ttyACM0`, it executes them only on next serial port",
"echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s),",
"standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo: Last Updated: May 20",
"if it happened in the first time when everything worked well. The output",
"\" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z jerk",
"I ran the command. I've also noticed that printer controller reboots every time",
"in general - but i want to be able to do it manually.",
"and the Cura itself can print things in general - but i want",
"Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo:",
"acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate",
"E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract",
"time the serial port is accessed, not sure if it happened in the",
"Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to low-level printer interface looked",
"execute at all. The interesting part is that Cura \"Monitor\" tab can actually",
"directly send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to",
"\" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\"",
"Cura itself can print things in general - but i want to be",
"repeated the whole process, but now `tail -f` didn't output anything and printer",
"I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init",
"can actually manipulate the caret and the Cura itself can print things in",
"that printer controller reboots every time the serial port is accessed, not sure",
"accepted answer from here to try moving this thing from terminal. [How to",
"echo: M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown",
"D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\"",
"Model of the printer is unknown, got it as present, probably something generic",
"together and with marlin firmware. I've used accepted answer from here to try",
"ok message into my terminal. Then i've turned the printer off and on",
"port is accessed, not sure if it happened in the first time when",
"echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok ``` The \"SD init",
"(mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo:",
"echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok",
"try moving this thing from terminal. [How to directly send G-code to printer",
"as present, probably something generic cartesian on arduino mega and ramps boards stitched",
"The \"SD init fail\" line and everything after it appears when sensor data",
"``` The \"SD init fail\" line and everything after it appears when sensor",
"feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201",
"before that during which the LCD is empty. If you send commands to",
"echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo:",
"data appears on the LCD, there's a delay before that during which the",
"the first time when everything worked well. The output of `cat /dev/ttyACM0` after",
"attempt to get access to low-level printer interface looked like that: ``` ./baud.py",
"boards stitched together and with marlin firmware. I've used accepted answer from here",
"that Cura \"Monitor\" tab can actually manipulate the caret and the Cura itself",
"(ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)",
"controller reboots every time the serial port is accessed, not sure if it",
"using something like `echo \"G0 X10\" > /dev/ttyACM0`, it executes them only on",
"X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced",
"(mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750",
"noticed that printer controller reboots every time the serial port is accessed, not",
"from terminal. [How to directly send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal)",
"mega and ramps boards stitched together and with marlin firmware. I've used accepted",
"used accepted answer from here to try moving this thing from terminal. [How",
"line instead of standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo: Last",
"Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00",
"send commands to printer using something like `echo \"G0 X10\" > /dev/ttyACM0`, it",
"failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok",
"command: \"okechecho\" ok ``` The \"SD init fail\" line and everything after it",
"and ramps boards stitched together and with marlin firmware. I've used accepted answer",
"ramps boards stitched together and with marlin firmware. I've used accepted answer from",
"- and there's garbage in the status line instead of standard \"%printername% ready\"",
"P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD",
"in the status line instead of standard \"%printername% ready\" as well: ``` start",
"of `cat /dev/ttyACM0` after baud setting is a bit weird too - and",
"command: \"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\"",
"Cura \"Monitor\" tab can actually manipulate the caret and the Cura itself can",
"off and on again and repeated the whole process, but now `tail -f`",
"config) Compiled: May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default",
"X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init fail",
"echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command:",
"first time when everything worked well. The output of `cat /dev/ttyACM0` after baud",
"terminal. Then i've turned the printer off and on again and repeated the",
"interesting part is that Cura \"Monitor\" tab can actually manipulate the caret and",
"Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo:",
"E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home",
"Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s):",
"S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY",
"the printer off and on again and repeated the whole process, but now",
"init fail\" line and everything after it appears when sensor data appears on",
"LCD displayed garbage in the status line after I ran the command. I've",
"too - and there's garbage in the status line instead of standard \"%printername%",
"feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk",
"not sure if it happened in the first time when everything worked well.",
"& cat > /dev/ttyACM0 ``` First it was fine: i've entered g-code, printer",
"ok echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok ``` The \"SD",
"after baud setting is a bit weird too - and there's garbage in",
"process, but now `tail -f` didn't output anything and printer LCD displayed garbage",
"accessing (and therefore reboot) - or doesn't execute at all. The interesting part",
"\"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command: \" (none, default",
"was fine: i've entered g-code, printer executed it and returned an ok message",
"fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command:",
"on again and repeated the whole process, but now `tail -f` didn't output",
"-f` didn't output anything and printer LCD displayed garbage in the status line",
"./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First",
"into my terminal. Then i've turned the printer off and on again and",
"but now `tail -f` didn't output anything and printer LCD displayed garbage in",
"marlin firmware. I've used accepted answer from here to try moving this thing",
"printer controller reboots every time the serial port is accessed, not sure if",
"(mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00",
"looked like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat",
"M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50",
"baud setting is a bit weird too - and there's garbage in the",
"Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min",
"accessed, not sure if it happened in the first time when everything worked",
"``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ```",
"anything and printer LCD displayed garbage in the status line after I ran",
"\"PID settings\" ok echo:Unknown command: \"okechecho\" ok ``` The \"SD init fail\" line",
"ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00",
"on the LCD, there's a delay before that during which the LCD is",
"S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00",
"appears when sensor data appears on the LCD, there's a delay before that",
"the whole process, but now `tail -f` didn't output anything and printer LCD",
"echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms),",
"everything after it appears when sensor data appears on the LCD, there's a",
"serial port is accessed, not sure if it happened in the first time",
"/dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it was",
"init fail echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown",
"empty. If you send commands to printer using something like `echo \"G0 X10\"",
"\"G0 X10\" > /dev/ttyACM0`, it executes them only on next serial port accessing",
"B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID",
"Last Updated: May 20 2017 18:12:04 | Author: (none, default config) Compiled: May",
"May 20 2017 18:12:04 | Author: (none, default config) Compiled: May 20 2017",
"Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo: M92",
"(mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00",
"didn't output anything and printer LCD displayed garbage in the status line after",
"that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0",
"this thing from terminal. [How to directly send G-code to printer from a",
"in the first time when everything worked well. The output of `cat /dev/ttyACM0`",
"g-code, printer executed it and returned an ok message into my terminal. Then",
"caret and the Cura itself can print things in general - but i",
"May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded",
"when sensor data appears on the LCD, there's a delay before that during",
"after it appears when sensor data appears on the LCD, there's a delay",
"i've entered g-code, printer executed it and returned an ok message into my",
"line after I ran the command. I've also noticed that printer controller reboots",
"terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to low-level printer interface looked like",
"echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04 | Author: (none, default config)",
"terminal. [How to directly send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My",
"ok ``` The \"SD init fail\" line and everything after it appears when",
"part is that Cura \"Monitor\" tab can actually manipulate the caret and the",
"E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset",
"on next serial port accessing (and therefore reboot) - or doesn't execute at",
"default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown",
"echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94",
"I've also noticed that printer controller reboots every time the serial port is",
"the status line instead of standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0",
"commands to printer using something like `echo \"G0 X10\" > /dev/ttyACM0`, it executes",
"again and repeated the whole process, but now `tail -f` didn't output anything",
"\"SD init failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00",
"happened in the first time when everything worked well. The output of `cat",
"3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo: M92 X80.00",
"of standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo: Last Updated: May",
"ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown",
"Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000",
"unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00",
"Then i've turned the printer off and on again and repeated the whole",
"E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\"",
"setting is a bit weird too - and there's garbage in the status",
"(mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s),",
"/dev/ttyACM0`, it executes them only on next serial port accessing (and therefore reboot)",
"T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time",
"status line instead of standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo:",
"the command. I've also noticed that printer controller reboots every time the serial",
"answer from here to try moving this thing from terminal. [How to directly",
"like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 & cat >",
"Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration,",
"and repeated the whole process, but now `tail -f` didn't output anything and",
"ok echo:Unknown command: \"okechecho\" ok ``` The \"SD init fail\" line and everything",
"is accessed, not sure if it happened in the first time when everything",
"default config) Compiled: May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded",
"If you send commands to printer using something like `echo \"G0 X10\" >",
"next serial port accessing (and therefore reboot) - or doesn't execute at all.",
"echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00",
"it executes them only on next serial port accessing (and therefore reboot) -",
"command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum",
"jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm):",
"Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\"",
"a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to low-level printer interface",
"command\" ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk",
"to low-level printer interface looked like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail",
"comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum",
"variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum",
"2017 18:12:04 | Author: (none, default config) Compiled: May 20 2017 echo: Free",
"Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo:",
"present, probably something generic cartesian on arduino mega and ramps boards stitched together",
"from here to try moving this thing from terminal. [How to directly send",
"to printer using something like `echo \"G0 X10\" > /dev/ttyACM0`, it executes them",
"message into my terminal. Then i've turned the printer off and on again",
"M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00",
"to directly send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt",
"The interesting part is that Cura \"Monitor\" tab can actually manipulate the caret",
"echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\"",
"E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok",
"when everything worked well. The output of `cat /dev/ttyACM0` after baud setting is",
"jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok ```",
"command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown",
"things in general - but i want to be able to do it",
"echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750",
"it as present, probably something generic cartesian on arduino mega and ramps boards",
"fail\" line and everything after it appears when sensor data appears on the",
"`cat /dev/ttyACM0` after baud setting is a bit weird too - and there's",
"instead of standard \"%printername% ready\" as well: ``` start echo:Marlin1.0.0 echo: Last Updated:",
"20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps",
"returned an ok message into my terminal. Then i've turned the printer off",
"jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command:",
"> /dev/ttyACM0 ``` First it was fine: i've entered g-code, printer executed it",
"you send commands to printer using something like `echo \"G0 X10\" > /dev/ttyACM0`,",
"it happened in the first time when everything worked well. The output of",
"and there's garbage in the status line instead of standard \"%printername% ready\" as",
"S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment",
"jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown",
"the Cura itself can print things in general - but i want to",
"generic cartesian on arduino mega and ramps boards stitched together and with marlin",
"echo:Maximum Acceleration (mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration",
"print things in general - but i want to be able to do",
"interface looked like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0 &",
"Author: (none, default config) Compiled: May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes:",
"echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo:",
"E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration (mm/s2):",
"My first attempt to get access to low-level printer interface looked like that:",
"as well: ``` start echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04 |",
"cartesian on arduino mega and ramps boards stitched together and with marlin firmware.",
"1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit: echo: M92 X80.00 Y80.00 Z3200.00",
"X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings:",
"to get access to low-level printer interface looked like that: ``` ./baud.py <>",
"it and returned an ok message into my terminal. Then i've turned the",
"echo: Last Updated: May 20 2017 18:12:04 | Author: (none, default config) Compiled:",
"| Author: (none, default config) Compiled: May 20 2017 echo: Free Memory: 3763",
"S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min",
"serial port accessing (and therefore reboot) - or doesn't execute at all. The",
"arduino mega and ramps boards stitched together and with marlin firmware. I've used",
"printer interface looked like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f /dev/ttyACM0",
"send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get",
"X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo:",
"Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown",
"a delay before that during which the LCD is empty. If you send",
"on arduino mega and ramps boards stitched together and with marlin firmware. I've",
"start echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04 | Author: (none, default",
"printer is unknown, got it as present, probably something generic cartesian on arduino",
"ok echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown",
"config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command:",
"M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00",
"which the LCD is empty. If you send commands to printer using something",
"and returned an ok message into my terminal. Then i've turned the printer",
"garbage in the status line instead of standard \"%printername% ready\" as well: ```",
"jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00",
"echo:Unknown command: \"starto\" ok echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command: \"",
"printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to low-level",
"manipulate the caret and the Cura itself can print things in general -",
"is empty. If you send commands to printer using something like `echo \"G0",
"or doesn't execute at all. The interesting part is that Cura \"Monitor\" tab",
"Updated: May 20 2017 18:12:04 | Author: (none, default config) Compiled: May 20",
"executed it and returned an ok message into my terminal. Then i've turned",
"echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206",
"a bit weird too - and there's garbage in the status line instead",
"access to low-level printer interface looked like that: ``` ./baud.py <> /dev/ttyACM0 250000",
"T0.00 B20000 X20.00 Z1.00 E5.00 echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00",
"it was fine: i've entered g-code, printer executed it and returned an ok",
"here to try moving this thing from terminal. [How to directly send G-code",
"echo:Home offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20",
"(none, default config) Compiled: May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232",
"and on again and repeated the whole process, but now `tail -f` didn't",
"echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echo:Steps per unit:",
"there's a delay before that during which the LCD is empty. If you",
"echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk",
"printer off and on again and repeated the whole process, but now `tail",
"(and therefore reboot) - or doesn't execute at all. The interesting part is",
"like `echo \"G0 X10\" > /dev/ttyACM0`, it executes them only on next serial",
"is unknown, got it as present, probably something generic cartesian on arduino mega",
"after I ran the command. I've also noticed that printer controller reboots every",
"from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to low-level printer",
"(mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00",
"Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\"",
"Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables:",
"to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first attempt to get access to",
"now `tail -f` didn't output anything and printer LCD displayed garbage in the",
"M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init",
"fine: i've entered g-code, printer executed it and returned an ok message into",
"well: ``` start echo:Marlin1.0.0 echo: Last Updated: May 20 2017 18:12:04 | Author:",
"> /dev/ttyACM0`, it executes them only on next serial port accessing (and therefore",
"settings: echo: M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok",
"I've used accepted answer from here to try moving this thing from terminal.",
"20 2017 18:12:04 | Author: (none, default config) Compiled: May 20 2017 echo:",
"18:12:04 | Author: (none, default config) Compiled: May 20 2017 echo: Free Memory:",
"T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum",
"feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk",
"the caret and the Cura itself can print things in general - but",
"Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\" ok",
"something generic cartesian on arduino mega and ramps boards stitched together and with",
"LCD is empty. If you send commands to printer using something like `echo",
"and with marlin firmware. I've used accepted answer from here to try moving",
"well. The output of `cat /dev/ttyACM0` after baud setting is a bit weird",
"the status line after I ran the command. I've also noticed that printer",
"sure if it happened in the first time when everything worked well. The",
"also noticed that printer controller reboots every time the serial port is accessed,",
"bit weird too - and there's garbage in the status line instead of",
"(mm/s2): echo: M201 X750 Y750 Z100 E10000 echo:Acceleration: S=acceleration, T=retract acceleration echo: M204",
"M301 P22.20 I1.08 D114.00 echo:SD init fail echo:Unknown command: \"starto\" ok echo:Unknown command:",
"with marlin firmware. I've used accepted answer from here to try moving this",
"my terminal. Then i've turned the printer off and on again and repeated",
"250000 tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it was fine:",
"command: \"SD init failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00 Z2.50 E2rBy00.00",
"the serial port is accessed, not sure if it happened in the first",
"printer LCD displayed garbage in the status line after I ran the command.",
"\"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok",
"Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \"",
"command. I've also noticed that printer controller reboots every time the serial port",
"/dev/ttyACM0 ``` First it was fine: i've entered g-code, printer executed it and",
"displayed garbage in the status line after I ran the command. I've also",
"actually manipulate the caret and the Cura itself can print things in general",
"per unit: echo: M92 X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203",
"[How to directly send G-code to printer from a Linux terminal?](https://3dprinting.stackexchange.com/questions/3112/how-to-directly-send-g-code-to-printer-from-a-linux-terminal) My first",
"of the printer is unknown, got it as present, probably something generic cartesian",
"echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum",
"Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00 echo:Maximum Acceleration",
"itself can print things in general - but i want to be able",
"therefore reboot) - or doesn't execute at all. The interesting part is that",
"got it as present, probably something generic cartesian on arduino mega and ramps",
"that during which the LCD is empty. If you send commands to printer",
"T=retract acceleration echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel",
"the LCD is empty. If you send commands to printer using something like",
"XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) echo: M205",
"only on next serial port accessing (and therefore reboot) - or doesn't execute",
"low-level printer interface looked like that: ``` ./baud.py <> /dev/ttyACM0 250000 tail -f",
"something like `echo \"G0 X10\" > /dev/ttyACM0`, it executes them only on next",
"X80.00 Y80.00 Z3200.00 E97.94 echo:Maximum feedrates (mm/s): echo: M203 X50.00 Y50.00 Z2.50 E25.00",
"(mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok echo:Unknown command: \"okechecho\" ok ``` The",
"offset (mm): echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08",
"(none, default config)50.00 Z2.50 E2rBy00.00 Y0.00 Z0.00echo\" ok echo:Unknown command: \"Unknown command\" ok",
"travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z",
"probably something generic cartesian on arduino mega and ramps boards stitched together and",
"turned the printer off and on again and repeated the whole process, but",
"sensor data appears on the LCD, there's a delay before that during which",
"echo:Unknown command: \"SD init failstartuthor\" ok echo:Unknown command: \" (none, default config)50.00 Z2.50",
"ok echo:Unknown command: \"aximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E",
"echo: M204 S500.00 T500.00 echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s),",
"Z jerk (mm/s), E=maximum E jerk (mm/s)echo\" ok echo:Unknown command: \"PID settings\" ok",
"Compiled: May 20 2017 echo: Free Memory: 3763 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings",
"echo:Unknown command: \"Unknown command\" ok echo:Unknown command: \" \"starto\"own comm\" ok echo:Unknown command:",
"executes them only on next serial port accessing (and therefore reboot) - or",
"get access to low-level printer interface looked like that: ``` ./baud.py <> /dev/ttyACM0",
"jerk (mm/s), E=maximum E jerk (mm/s) echo: M205 S0.00 T0.00 B20000 X20.00 Z1.00",
"tail -f /dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it was fine: i've",
"/dev/ttyACM0 & cat > /dev/ttyACM0 ``` First it was fine: i've entered g-code,"
] |
[
"is called. For example there is a strap on the model for the",
"have found something called \"ghosting\", or at least I heard that is what",
"that is what it is called. For example there is a strap on",
"left and right there is very shallow \"straps\" or something happening. I am",
"shallow \"straps\" or something happening. I am interested to know what causes this",
"example there is a strap on the model for the pants. And going",
"some minion chess pieces for my teacher at school and on every model",
"I am printing some minion chess pieces for my teacher at school and",
"called \"ghosting\", or at least I heard that is what it is called.",
"minion chess pieces for my teacher at school and on every model I",
"for my teacher at school and on every model I have found something",
"to fix it. It is not super bad, but would be nice to",
"school and on every model I have found something called \"ghosting\", or at",
"to know what causes this to happen and how to fix it. It",
"am printing some minion chess pieces for my teacher at school and on",
"there is very shallow \"straps\" or something happening. I am interested to know",
"teacher at school and on every model I have found something called \"ghosting\",",
"on every model I have found something called \"ghosting\", or at least I",
"what it is called. For example there is a strap on the model",
"is a strap on the model for the pants. And going left and",
"or something happening. I am interested to know what causes this to happen",
"at school and on every model I have found something called \"ghosting\", or",
"there is a strap on the model for the pants. And going left",
"to happen and how to fix it. It is not super bad, but",
"\"ghosting\", or at least I heard that is what it is called. For",
"strap on the model for the pants. And going left and right there",
"happening. I am interested to know what causes this to happen and how",
"causes this to happen and how to fix it. It is not super",
"for the pants. And going left and right there is very shallow \"straps\"",
"on the model for the pants. And going left and right there is",
"least I heard that is what it is called. For example there is",
"is very shallow \"straps\" or something happening. I am interested to know what",
"the pants. And going left and right there is very shallow \"straps\" or",
"right there is very shallow \"straps\" or something happening. I am interested to",
"is what it is called. For example there is a strap on the",
"this to happen and how to fix it. It is not super bad,",
"going left and right there is very shallow \"straps\" or something happening. I",
"called. For example there is a strap on the model for the pants.",
"something called \"ghosting\", or at least I heard that is what it is",
"am interested to know what causes this to happen and how to fix",
"and how to fix it. It is not super bad, but would be",
"model I have found something called \"ghosting\", or at least I heard that",
"I have found something called \"ghosting\", or at least I heard that is",
"pieces for my teacher at school and on every model I have found",
"it is called. For example there is a strap on the model for",
"happen and how to fix it. It is not super bad, but would",
"printing some minion chess pieces for my teacher at school and on every",
"For example there is a strap on the model for the pants. And",
"and right there is very shallow \"straps\" or something happening. I am interested",
"I am interested to know what causes this to happen and how to",
"I heard that is what it is called. For example there is a",
"and on every model I have found something called \"ghosting\", or at least",
"how to fix it. It is not super bad, but would be nice",
"know what causes this to happen and how to fix it. It is",
"And going left and right there is very shallow \"straps\" or something happening.",
"at least I heard that is what it is called. For example there",
"very shallow \"straps\" or something happening. I am interested to know what causes",
"model for the pants. And going left and right there is very shallow",
"\"straps\" or something happening. I am interested to know what causes this to",
"what causes this to happen and how to fix it. It is not",
"found something called \"ghosting\", or at least I heard that is what it",
"or at least I heard that is what it is called. For example",
"chess pieces for my teacher at school and on every model I have",
"heard that is what it is called. For example there is a strap",
"pants. And going left and right there is very shallow \"straps\" or something",
"every model I have found something called \"ghosting\", or at least I heard",
"interested to know what causes this to happen and how to fix it.",
"my teacher at school and on every model I have found something called",
"a strap on the model for the pants. And going left and right",
"fix it. It is not super bad, but would be nice to fix.",
"the model for the pants. And going left and right there is very",
"something happening. I am interested to know what causes this to happen and"
] |
[
"The extrusion temperature is set at 190 °C for PLA but the temperature",
"set at 190 °C for PLA but the temperature never quite gets that",
"°C. So the printer never prints. The bed temperature is fine. Any suggestions",
"never prints. The bed temperature is fine. Any suggestions on how to fix?",
"A8 with Cura. First time use. The extrusion temperature is set at 190",
"the temperature never quite gets that hot, e.g. 189.2 °C. So the printer",
"190 °C for PLA but the temperature never quite gets that hot, e.g.",
"printer never prints. The bed temperature is fine. Any suggestions on how to",
"Anet A8 with Cura. First time use. The extrusion temperature is set at",
"So the printer never prints. The bed temperature is fine. Any suggestions on",
"the printer never prints. The bed temperature is fine. Any suggestions on how",
"extrusion temperature is set at 190 °C for PLA but the temperature never",
"that hot, e.g. 189.2 °C. So the printer never prints. The bed temperature",
"never quite gets that hot, e.g. 189.2 °C. So the printer never prints.",
"temperature is set at 190 °C for PLA but the temperature never quite",
"Cura. First time use. The extrusion temperature is set at 190 °C for",
"quite gets that hot, e.g. 189.2 °C. So the printer never prints. The",
"for PLA but the temperature never quite gets that hot, e.g. 189.2 °C.",
"°C for PLA but the temperature never quite gets that hot, e.g. 189.2",
"189.2 °C. So the printer never prints. The bed temperature is fine. Any",
"is set at 190 °C for PLA but the temperature never quite gets",
"use. The extrusion temperature is set at 190 °C for PLA but the",
"but the temperature never quite gets that hot, e.g. 189.2 °C. So the",
"PLA but the temperature never quite gets that hot, e.g. 189.2 °C. So",
"time use. The extrusion temperature is set at 190 °C for PLA but",
"hot, e.g. 189.2 °C. So the printer never prints. The bed temperature is",
"with Cura. First time use. The extrusion temperature is set at 190 °C",
"at 190 °C for PLA but the temperature never quite gets that hot,",
"gets that hot, e.g. 189.2 °C. So the printer never prints. The bed",
"e.g. 189.2 °C. So the printer never prints. The bed temperature is fine.",
"First time use. The extrusion temperature is set at 190 °C for PLA",
"temperature never quite gets that hot, e.g. 189.2 °C. So the printer never"
] |
[
"(read single extrusion) or do I need to use a single extrusion head",
"purpose printing (read single extrusion) or do I need to use a single",
"to 3D printing and I recently got a LulzBot Taz 6 printer. I'm",
"to use a single extrusion head for single extrusion print jobs. If you",
"new to 3D printing and I recently got a LulzBot Taz 6 printer.",
"Extruder v3 Tool Head) for general purpose printing (read single extrusion) or do",
"use a dual for single use, why buy single extruders (I've been looking",
"of a dual head? If you should use a single extruder for non-dual",
"for general purpose printing (read single extrusion) or do I need to use",
"handle all the filament types that I am interested in. Here is the",
"particular, the LulzBot TAZ Dual Extruder v3 Tool Head) for general purpose printing",
"experiment with printing flexible filament. The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head)",
"interested in doing dual extrusion printing (especially with dissolvable supports), but I'm also",
"Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the filament types that I am",
"3D printing and I recently got a LulzBot Taz 6 printer. I'm interested",
"performance out of a dual head? If you should use a single extruder",
"you can get the same performance out of a dual head? If you",
"If you should use a single extruder for non-dual prints, please explain the",
"printer. I'm interested in doing dual extrusion printing (especially with dissolvable supports), but",
"doing single extrusion prints. In particular, I would like to experiment with printing",
"Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get the same performance",
"TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get the same",
"dual extrusion printing (especially with dissolvable supports), but I'm also interested in doing",
"The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle",
"printing and I recently got a LulzBot Taz 6 printer. I'm interested in",
"I'm also interested in doing single extrusion prints. In particular, I would like",
"a LulzBot Taz 6 printer. I'm interested in doing dual extrusion printing (especially",
"can I use a dual extruder (in particular, the LulzBot TAZ Dual Extruder",
"can handle all the filament types that I am interested in. Here is",
"single extrusion head for single extrusion print jobs. If you can use a",
"buy single extruders (I've been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for",
"LulzBot Taz 6 printer. I'm interested in doing dual extrusion printing (especially with",
"extrusion prints. In particular, I would like to experiment with printing flexible filament.",
"filament. The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can",
"Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the filament types",
"says that it can handle all the filament types that I am interested",
"out of a dual head? If you should use a single extruder for",
"TAZ Dual Extruder v3 Tool Head) for general purpose printing (read single extrusion)",
"you can use a dual for single use, why buy single extruders (I've",
"interested in. Here is the question: can I use a dual extruder (in",
"general purpose printing (read single extrusion) or do I need to use a",
"particular, I would like to experiment with printing flexible filament. The [LulzBot TAZ",
"the LulzBot TAZ Dual Extruder v3 Tool Head) for general purpose printing (read",
"extrusion head for single extrusion print jobs. If you can use a dual",
"to experiment with printing flexible filament. The [LulzBot TAZ Dual Extruder v3 Tool",
"use a dual extruder (in particular, the LulzBot TAZ Dual Extruder v3 Tool",
"for flexy prints) if you can get the same performance out of a",
"single extruder for non-dual prints, please explain the shortcomings of using a dual",
"why buy single extruders (I've been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head)",
"with dissolvable supports), but I'm also interested in doing single extrusion prints. In",
"dual head? If you should use a single extruder for non-dual prints, please",
"question: can I use a dual extruder (in particular, the LulzBot TAZ Dual",
"also interested in doing single extrusion prints. In particular, I would like to",
"a dual extruder (in particular, the LulzBot TAZ Dual Extruder v3 Tool Head)",
"TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the",
"can get the same performance out of a dual head? If you should",
"jobs. If you can use a dual for single use, why buy single",
"prints, please explain the shortcomings of using a dual print head for general",
"in doing single extrusion prints. In particular, I would like to experiment with",
"If you can use a dual for single use, why buy single extruders",
"Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the filament",
"that I am interested in. Here is the question: can I use a",
"in. Here is the question: can I use a dual extruder (in particular,",
"Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the filament types that I",
"supports), but I'm also interested in doing single extrusion prints. In particular, I",
"Dual Extruder v3 Tool Head) for general purpose printing (read single extrusion) or",
"for non-dual prints, please explain the shortcomings of using a dual print head",
"for single use, why buy single extruders (I've been looking at [LulzBot TAZ",
"if you can get the same performance out of a dual head? If",
"it can handle all the filament types that I am interested in. Here",
"printing (read single extrusion) or do I need to use a single extrusion",
"got a LulzBot Taz 6 printer. I'm interested in doing dual extrusion printing",
"extrusion) or do I need to use a single extrusion head for single",
"I am interested in. Here is the question: can I use a dual",
"doing dual extrusion printing (especially with dissolvable supports), but I'm also interested in",
"single extrusion prints. In particular, I would like to experiment with printing flexible",
"(in particular, the LulzBot TAZ Dual Extruder v3 Tool Head) for general purpose",
"extrusion printing (especially with dissolvable supports), but I'm also interested in doing single",
"been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you",
"a single extrusion head for single extrusion print jobs. If you can use",
"dual for single use, why buy single extruders (I've been looking at [LulzBot",
"(I've been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if",
"6 printer. I'm interested in doing dual extrusion printing (especially with dissolvable supports),",
"the question: can I use a dual extruder (in particular, the LulzBot TAZ",
"single extrusion print jobs. If you can use a dual for single use,",
"Tool Head) for general purpose printing (read single extrusion) or do I need",
"do I need to use a single extrusion head for single extrusion print",
"I would like to experiment with printing flexible filament. The [LulzBot TAZ Dual",
"[LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all",
"Here is the question: can I use a dual extruder (in particular, the",
"use a single extruder for non-dual prints, please explain the shortcomings of using",
"and I recently got a LulzBot Taz 6 printer. I'm interested in doing",
"get the same performance out of a dual head? If you should use",
"a single extruder for non-dual prints, please explain the shortcomings of using a",
"I'm interested in doing dual extrusion printing (especially with dissolvable supports), but I'm",
"in doing dual extrusion printing (especially with dissolvable supports), but I'm also interested",
"you should use a single extruder for non-dual prints, please explain the shortcomings",
"Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get the same performance out of",
"interested in doing single extrusion prints. In particular, I would like to experiment",
"extruder (in particular, the LulzBot TAZ Dual Extruder v3 Tool Head) for general",
"a dual for single use, why buy single extruders (I've been looking at",
"prints) if you can get the same performance out of a dual head?",
"flexy prints) if you can get the same performance out of a dual",
"would like to experiment with printing flexible filament. The [LulzBot TAZ Dual Extruder",
"Head) for general purpose printing (read single extrusion) or do I need to",
"is the question: can I use a dual extruder (in particular, the LulzBot",
"like to experiment with printing flexible filament. The [LulzBot TAZ Dual Extruder v3",
"the filament types that I am interested in. Here is the question: can",
"can use a dual for single use, why buy single extruders (I've been",
"I recently got a LulzBot Taz 6 printer. I'm interested in doing dual",
"[LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get the",
"v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it can handle all the filament types that",
"non-dual prints, please explain the shortcomings of using a dual print head for",
"extrusion print jobs. If you can use a dual for single use, why",
"same performance out of a dual head? If you should use a single",
"am interested in. Here is the question: can I use a dual extruder",
"at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get",
"Taz 6 printer. I'm interested in doing dual extrusion printing (especially with dissolvable",
"I use a dual extruder (in particular, the LulzBot TAZ Dual Extruder v3",
"all the filament types that I am interested in. Here is the question:",
"v3 Tool Head) for general purpose printing (read single extrusion) or do I",
"printing (especially with dissolvable supports), but I'm also interested in doing single extrusion",
"types that I am interested in. Here is the question: can I use",
"explain the shortcomings of using a dual print head for general purpose use.",
"filament types that I am interested in. Here is the question: can I",
"dissolvable supports), but I'm also interested in doing single extrusion prints. In particular,",
"(especially with dissolvable supports), but I'm also interested in doing single extrusion prints.",
"need to use a single extrusion head for single extrusion print jobs. If",
"extruders (I've been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints)",
"with printing flexible filament. The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says",
"for single extrusion print jobs. If you can use a dual for single",
"single extruders (I've been looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy",
"printing flexible filament. The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that",
"In particular, I would like to experiment with printing flexible filament. The [LulzBot",
"but I'm also interested in doing single extrusion prints. In particular, I would",
"Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can get the same performance out",
"I need to use a single extrusion head for single extrusion print jobs.",
"single extrusion) or do I need to use a single extrusion head for",
"that it can handle all the filament types that I am interested in.",
"LulzBot TAZ Dual Extruder v3 Tool Head) for general purpose printing (read single",
"print jobs. If you can use a dual for single use, why buy",
"please explain the shortcomings of using a dual print head for general purpose",
"prints. In particular, I would like to experiment with printing flexible filament. The",
"extruder for non-dual prints, please explain the shortcomings of using a dual print",
"single use, why buy single extruders (I've been looking at [LulzBot TAZ Aerostruder",
"or do I need to use a single extrusion head for single extrusion",
"use a single extrusion head for single extrusion print jobs. If you can",
"head for single extrusion print jobs. If you can use a dual for",
"the same performance out of a dual head? If you should use a",
"I'm new to 3D printing and I recently got a LulzBot Taz 6",
"should use a single extruder for non-dual prints, please explain the shortcomings of",
"use, why buy single extruders (I've been looking at [LulzBot TAZ Aerostruder Tool",
"recently got a LulzBot Taz 6 printer. I'm interested in doing dual extrusion",
"flexible filament. The [LulzBot TAZ Dual Extruder v3 Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-dual-extruder-v3-tool-head) says that it",
"dual extruder (in particular, the LulzBot TAZ Dual Extruder v3 Tool Head) for",
"a dual head? If you should use a single extruder for non-dual prints,",
"head? If you should use a single extruder for non-dual prints, please explain",
"looking at [LulzBot TAZ Aerostruder Tool Head](https://www.lulzbot.com/store/tool-heads/lulzbot-taz-aerostruder-tool-head) for flexy prints) if you can"
] |
[
"PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how",
"OD)\"* Anybody know how this is fitted? Is it simply tapping the feed",
"an extruder mod on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters)",
"extruder mod on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters) with",
"Anybody know how this is fitted? Is it simply tapping the feed hole",
"(2.0mm ID/4.0mm OD)\"* Anybody know how this is fitted? Is it simply tapping",
"4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody",
"Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters) with 4 Pcs PC4-M6",
"this is fitted? Is it simply tapping the feed hole on the top?",
"ID/4.0mm OD)\"* Anybody know how this is fitted? Is it simply tapping the",
"I saw an extruder mod on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube",
"with 4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"*",
"Pcs PTFE Teflon Tube (2 Meters) with 4 Pcs PC4-M6 Fittings for 3D",
"how this is fitted? Is it simply tapping the feed hole on the",
"on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters) with 4 Pcs",
"Teflon Tube (2 Meters) with 4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm",
"Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this",
"Tube (2 Meters) with 4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament",
"know how this is fitted? Is it simply tapping the feed hole on",
"(2 Meters) with 4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm",
"Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know",
"for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this is",
"1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this is fitted? Is it",
"2 Pcs PTFE Teflon Tube (2 Meters) with 4 Pcs PC4-M6 Fittings for",
"PTFE Teflon Tube (2 Meters) with 4 Pcs PC4-M6 Fittings for 3D Printer",
"*\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters) with 4 Pcs PC4-M6 Fittings",
"Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this is fitted? Is",
"Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this is fitted? Is it simply",
"3D Printer 1.75mm Filament (2.0mm ID/4.0mm OD)\"* Anybody know how this is fitted?",
"saw an extruder mod on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2",
"mod on Amazon *\"EAONE 2 Pcs PTFE Teflon Tube (2 Meters) with 4",
"Meters) with 4 Pcs PC4-M6 Fittings for 3D Printer 1.75mm Filament (2.0mm ID/4.0mm"
] |
[
"getting it to line up with the whole is a nightmare. Can the",
"alter the fan so I can see the filament when I am loading",
"doable. I am now trying with PLA and getting it to line up",
"nightmare. Can the driving cog and guide wheel be moved? A couple of",
"ABS and took the advice to alter the fan so I can see",
"I am now trying with PLA and getting it to line up with",
"PLA and getting it to line up with the whole is a nightmare.",
"driving cog and guide wheel be moved? A couple of mm would stop",
"see the filament when I am loading it into the cold end. It",
"I can see the filament when I am loading it into the cold",
"filament when I am loading it into the cold end. It was tricky",
"had been printing with ABS and took the advice to alter the fan",
"fan so I can see the filament when I am loading it into",
"is a nightmare. Can the driving cog and guide wheel be moved? A",
"so I can see the filament when I am loading it into the",
"the whole is a nightmare. Can the driving cog and guide wheel be",
"and took the advice to alter the fan so I can see the",
"advice to alter the fan so I can see the filament when I",
"whole is a nightmare. Can the driving cog and guide wheel be moved?",
"with ABS and took the advice to alter the fan so I can",
"am loading it into the cold end. It was tricky but doable. I",
"and getting it to line up with the whole is a nightmare. Can",
"cog and guide wheel be moved? A couple of mm would stop the",
"and guide wheel be moved? A couple of mm would stop the driving",
"the filament when I am loading it into the cold end. It was",
"am now trying with PLA and getting it to line up with the",
"been printing with ABS and took the advice to alter the fan so",
"now trying with PLA and getting it to line up with the whole",
"to alter the fan so I can see the filament when I am",
"guide wheel be moved? A couple of mm would stop the driving cog",
"up with the whole is a nightmare. Can the driving cog and guide",
"printing with ABS and took the advice to alter the fan so I",
"the cold end. It was tricky but doable. I am now trying with",
"It was tricky but doable. I am now trying with PLA and getting",
"the fan so I can see the filament when I am loading it",
"a nightmare. Can the driving cog and guide wheel be moved? A couple",
"wheel be moved? A couple of mm would stop the driving cog pushing",
"it into the cold end. It was tricky but doable. I am now",
"with PLA and getting it to line up with the whole is a",
"it to line up with the whole is a nightmare. Can the driving",
"I had been printing with ABS and took the advice to alter the",
"to line up with the whole is a nightmare. Can the driving cog",
"line up with the whole is a nightmare. Can the driving cog and",
"be moved? A couple of mm would stop the driving cog pushing the",
"took the advice to alter the fan so I can see the filament",
"when I am loading it into the cold end. It was tricky but",
"trying with PLA and getting it to line up with the whole is",
"I am loading it into the cold end. It was tricky but doable.",
"the advice to alter the fan so I can see the filament when",
"the driving cog and guide wheel be moved? A couple of mm would",
"loading it into the cold end. It was tricky but doable. I am",
"Can the driving cog and guide wheel be moved? A couple of mm",
"with the whole is a nightmare. Can the driving cog and guide wheel",
"moved? A couple of mm would stop the driving cog pushing the filament",
"A couple of mm would stop the driving cog pushing the filament off",
"into the cold end. It was tricky but doable. I am now trying",
"was tricky but doable. I am now trying with PLA and getting it",
"tricky but doable. I am now trying with PLA and getting it to",
"end. It was tricky but doable. I am now trying with PLA and",
"can see the filament when I am loading it into the cold end.",
"cold end. It was tricky but doable. I am now trying with PLA",
"couple of mm would stop the driving cog pushing the filament off line.",
"but doable. I am now trying with PLA and getting it to line"
] |
[
"running on ramps 1.4 When i start a new print and the hotend",
"start coming out of the hotend. This goes on for as long as",
"goes on for as long as the temperature is kept above melting point,",
"3D printer running on ramps 1.4 When i start a new print and",
"I am currently using simplify if that makes any difference regarding configuration. Any",
"above melting point, without moving the extrusion gear. The extruder is a bowden",
"that makes any difference regarding configuration. Any ideas what to do to prevent",
"the hotend reaches melting point of PLA, the PLA start coming out of",
"new print and the hotend reaches melting point of PLA, the PLA start",
"currently using simplify if that makes any difference regarding configuration. Any ideas what",
"point, without moving the extrusion gear. The extruder is a bowden type. Hotend",
"Hotend is a J-head. I am currently using simplify if that makes any",
"is a bowden type. Hotend is a J-head. I am currently using simplify",
"makes any difference regarding configuration. Any ideas what to do to prevent this",
"1.4 When i start a new print and the hotend reaches melting point",
"difference regarding configuration. Any ideas what to do to prevent this from happening?",
"is kept above melting point, without moving the extrusion gear. The extruder is",
"extrusion gear. The extruder is a bowden type. Hotend is a J-head. I",
"on for as long as the temperature is kept above melting point, without",
"i start a new print and the hotend reaches melting point of PLA,",
"ramps 1.4 When i start a new print and the hotend reaches melting",
"hotend. This goes on for as long as the temperature is kept above",
"moving the extrusion gear. The extruder is a bowden type. Hotend is a",
"printer running on ramps 1.4 When i start a new print and the",
"for as long as the temperature is kept above melting point, without moving",
"long as the temperature is kept above melting point, without moving the extrusion",
"J-head. I am currently using simplify if that makes any difference regarding configuration.",
"PLA start coming out of the hotend. This goes on for as long",
"the temperature is kept above melting point, without moving the extrusion gear. The",
"on ramps 1.4 When i start a new print and the hotend reaches",
"hotend reaches melting point of PLA, the PLA start coming out of the",
"of the hotend. This goes on for as long as the temperature is",
"as the temperature is kept above melting point, without moving the extrusion gear.",
"The extruder is a bowden type. Hotend is a J-head. I am currently",
"as long as the temperature is kept above melting point, without moving the",
"This goes on for as long as the temperature is kept above melting",
"melting point of PLA, the PLA start coming out of the hotend. This",
"reaches melting point of PLA, the PLA start coming out of the hotend.",
"kept above melting point, without moving the extrusion gear. The extruder is a",
"gear. The extruder is a bowden type. Hotend is a J-head. I am",
"any difference regarding configuration. Any ideas what to do to prevent this from",
"a J-head. I am currently using simplify if that makes any difference regarding",
"have a homemade 3D printer running on ramps 1.4 When i start a",
"of PLA, the PLA start coming out of the hotend. This goes on",
"and the hotend reaches melting point of PLA, the PLA start coming out",
"the PLA start coming out of the hotend. This goes on for as",
"is a J-head. I am currently using simplify if that makes any difference",
"type. Hotend is a J-head. I am currently using simplify if that makes",
"a bowden type. Hotend is a J-head. I am currently using simplify if",
"a new print and the hotend reaches melting point of PLA, the PLA",
"melting point, without moving the extrusion gear. The extruder is a bowden type.",
"the hotend. This goes on for as long as the temperature is kept",
"homemade 3D printer running on ramps 1.4 When i start a new print",
"out of the hotend. This goes on for as long as the temperature",
"print and the hotend reaches melting point of PLA, the PLA start coming",
"I have a homemade 3D printer running on ramps 1.4 When i start",
"extruder is a bowden type. Hotend is a J-head. I am currently using",
"a homemade 3D printer running on ramps 1.4 When i start a new",
"start a new print and the hotend reaches melting point of PLA, the",
"am currently using simplify if that makes any difference regarding configuration. Any ideas",
"temperature is kept above melting point, without moving the extrusion gear. The extruder",
"point of PLA, the PLA start coming out of the hotend. This goes",
"simplify if that makes any difference regarding configuration. Any ideas what to do",
"coming out of the hotend. This goes on for as long as the",
"the extrusion gear. The extruder is a bowden type. Hotend is a J-head.",
"without moving the extrusion gear. The extruder is a bowden type. Hotend is",
"bowden type. Hotend is a J-head. I am currently using simplify if that",
"using simplify if that makes any difference regarding configuration. Any ideas what to",
"PLA, the PLA start coming out of the hotend. This goes on for",
"When i start a new print and the hotend reaches melting point of",
"if that makes any difference regarding configuration. Any ideas what to do to"
] |
[
"is that if you don't apply it perfectly cleanly, it leaves very noticeable",
"I printed out of PLA to a small titanium rod. I've previously used",
"stains on the PLA. Can anyone recommend a good glue for this application",
"printed out of PLA to a small titanium rod. I've previously used Superglue",
"pieces to each other with great success, but the problem is that if",
"to each other with great success, but the problem is that if you",
"it perfectly cleanly, it leaves very noticeable stains on the PLA. Can anyone",
"leaves very noticeable stains on the PLA. Can anyone recommend a good glue",
"recommend a good glue for this application that won't leave stains like that?",
"of PLA to a small titanium rod. I've previously used Superglue (cyanoacrylate) to",
"Superglue (cyanoacrylate) to glue PLA pieces to each other with great success, but",
"piece I printed out of PLA to a small titanium rod. I've previously",
"PLA. Can anyone recommend a good glue for this application that won't leave",
"it leaves very noticeable stains on the PLA. Can anyone recommend a good",
"I've previously used Superglue (cyanoacrylate) to glue PLA pieces to each other with",
"apply it perfectly cleanly, it leaves very noticeable stains on the PLA. Can",
"out of PLA to a small titanium rod. I've previously used Superglue (cyanoacrylate)",
"glue PLA pieces to each other with great success, but the problem is",
"problem is that if you don't apply it perfectly cleanly, it leaves very",
"other with great success, but the problem is that if you don't apply",
"PLA pieces to each other with great success, but the problem is that",
"Can anyone recommend a good glue for this application that won't leave stains",
"don't apply it perfectly cleanly, it leaves very noticeable stains on the PLA.",
"rod. I've previously used Superglue (cyanoacrylate) to glue PLA pieces to each other",
"to glue PLA pieces to each other with great success, but the problem",
"the PLA. Can anyone recommend a good glue for this application that won't",
"each other with great success, but the problem is that if you don't",
"the problem is that if you don't apply it perfectly cleanly, it leaves",
"I'd like to attach a piece I printed out of PLA to a",
"cleanly, it leaves very noticeable stains on the PLA. Can anyone recommend a",
"a piece I printed out of PLA to a small titanium rod. I've",
"very noticeable stains on the PLA. Can anyone recommend a good glue for",
"like to attach a piece I printed out of PLA to a small",
"to a small titanium rod. I've previously used Superglue (cyanoacrylate) to glue PLA",
"on the PLA. Can anyone recommend a good glue for this application that",
"(cyanoacrylate) to glue PLA pieces to each other with great success, but the",
"used Superglue (cyanoacrylate) to glue PLA pieces to each other with great success,",
"small titanium rod. I've previously used Superglue (cyanoacrylate) to glue PLA pieces to",
"perfectly cleanly, it leaves very noticeable stains on the PLA. Can anyone recommend",
"previously used Superglue (cyanoacrylate) to glue PLA pieces to each other with great",
"a small titanium rod. I've previously used Superglue (cyanoacrylate) to glue PLA pieces",
"PLA to a small titanium rod. I've previously used Superglue (cyanoacrylate) to glue",
"with great success, but the problem is that if you don't apply it",
"success, but the problem is that if you don't apply it perfectly cleanly,",
"titanium rod. I've previously used Superglue (cyanoacrylate) to glue PLA pieces to each",
"if you don't apply it perfectly cleanly, it leaves very noticeable stains on",
"great success, but the problem is that if you don't apply it perfectly",
"that if you don't apply it perfectly cleanly, it leaves very noticeable stains",
"but the problem is that if you don't apply it perfectly cleanly, it",
"noticeable stains on the PLA. Can anyone recommend a good glue for this",
"you don't apply it perfectly cleanly, it leaves very noticeable stains on the",
"attach a piece I printed out of PLA to a small titanium rod.",
"to attach a piece I printed out of PLA to a small titanium",
"anyone recommend a good glue for this application that won't leave stains like"
] |
[
"a sharp pull. This worked really well. I am trying to print with",
"to drop to around 190deg c then a sharp pull. This worked really",
"hot end to I get left with a length of PLA in the",
"matter what temperature I drop the hot end to I get left with",
"the feeder tube. OK I can heat the hot end and poke the",
"I can heat the hot end and poke the excess down with a",
"I read that the best way of removing ABS was to let the",
"at the hot end to drop to around 190deg c then a sharp",
"PLA but no matter what temperature I drop the hot end to I",
"I get left with a length of PLA in the feeder tube. OK",
"a wire but that is a pain. I think the technique is right",
"around 190deg c then a sharp pull. This worked really well. I am",
"trying to print with PLA but no matter what temperature I drop the",
"is a pain. I think the technique is right but the temperature is",
"am trying to print with PLA but no matter what temperature I drop",
"that the best way of removing ABS was to let the temperature at",
"with a length of PLA in the feeder tube. OK I can heat",
"pain. I think the technique is right but the temperature is wrong. Any",
"way of removing ABS was to let the temperature at the hot end",
"best way of removing ABS was to let the temperature at the hot",
"removing ABS was to let the temperature at the hot end to drop",
"the excess down with a wire but that is a pain. I think",
"ABS was to let the temperature at the hot end to drop to",
"the hot end to drop to around 190deg c then a sharp pull.",
"hot end to drop to around 190deg c then a sharp pull. This",
"I think the technique is right but the temperature is wrong. Any help",
"of PLA in the feeder tube. OK I can heat the hot end",
"heat the hot end and poke the excess down with a wire but",
"with PLA but no matter what temperature I drop the hot end to",
"end to I get left with a length of PLA in the feeder",
"PLA in the feeder tube. OK I can heat the hot end and",
"to I get left with a length of PLA in the feeder tube.",
"was to let the temperature at the hot end to drop to around",
"the best way of removing ABS was to let the temperature at the",
"drop to around 190deg c then a sharp pull. This worked really well.",
"and poke the excess down with a wire but that is a pain.",
"excess down with a wire but that is a pain. I think the",
"end to drop to around 190deg c then a sharp pull. This worked",
"the temperature at the hot end to drop to around 190deg c then",
"but no matter what temperature I drop the hot end to I get",
"think the technique is right but the temperature is wrong. Any help great",
"wire but that is a pain. I think the technique is right but",
"poke the excess down with a wire but that is a pain. I",
"sharp pull. This worked really well. I am trying to print with PLA",
"the hot end and poke the excess down with a wire but that",
"read that the best way of removing ABS was to let the temperature",
"left with a length of PLA in the feeder tube. OK I can",
"pull. This worked really well. I am trying to print with PLA but",
"print with PLA but no matter what temperature I drop the hot end",
"in the feeder tube. OK I can heat the hot end and poke",
"to print with PLA but no matter what temperature I drop the hot",
"drop the hot end to I get left with a length of PLA",
"190deg c then a sharp pull. This worked really well. I am trying",
"with a wire but that is a pain. I think the technique is",
"the hot end to I get left with a length of PLA in",
"tube. OK I can heat the hot end and poke the excess down",
"c then a sharp pull. This worked really well. I am trying to",
"worked really well. I am trying to print with PLA but no matter",
"I drop the hot end to I get left with a length of",
"can heat the hot end and poke the excess down with a wire",
"to around 190deg c then a sharp pull. This worked really well. I",
"I am trying to print with PLA but no matter what temperature I",
"the technique is right but the temperature is wrong. Any help great fully",
"end and poke the excess down with a wire but that is a",
"but that is a pain. I think the technique is right but the",
"temperature I drop the hot end to I get left with a length",
"really well. I am trying to print with PLA but no matter what",
"technique is right but the temperature is wrong. Any help great fully appreciated.",
"let the temperature at the hot end to drop to around 190deg c",
"length of PLA in the feeder tube. OK I can heat the hot",
"no matter what temperature I drop the hot end to I get left",
"OK I can heat the hot end and poke the excess down with",
"to let the temperature at the hot end to drop to around 190deg",
"then a sharp pull. This worked really well. I am trying to print",
"temperature at the hot end to drop to around 190deg c then a",
"a length of PLA in the feeder tube. OK I can heat the",
"feeder tube. OK I can heat the hot end and poke the excess",
"what temperature I drop the hot end to I get left with a",
"This worked really well. I am trying to print with PLA but no",
"down with a wire but that is a pain. I think the technique",
"of removing ABS was to let the temperature at the hot end to",
"get left with a length of PLA in the feeder tube. OK I",
"that is a pain. I think the technique is right but the temperature",
"hot end and poke the excess down with a wire but that is",
"well. I am trying to print with PLA but no matter what temperature",
"a pain. I think the technique is right but the temperature is wrong."
] |
[
"I want the long side of it printed in the vertical direction or",
"filaments suggest \"reducing cross-sectional area\" of the print. Is this referring to the",
"area\" of the print. Is this referring to the vertical plane or horizontal",
"cross-sectional area\" of the print. Is this referring to the vertical plane or",
"rectangular prism, would I want the long side of it printed in the",
"or horizontal plane? In other words, if I were to print a rectangular",
"words, if I were to print a rectangular prism, would I want the",
"plane? In other words, if I were to print a rectangular prism, would",
"suggest \"reducing cross-sectional area\" of the print. Is this referring to the vertical",
"if I were to print a rectangular prism, would I want the long",
"In other words, if I were to print a rectangular prism, would I",
"I were to print a rectangular prism, would I want the long side",
"were to print a rectangular prism, would I want the long side of",
"print a rectangular prism, would I want the long side of it printed",
"the print. Is this referring to the vertical plane or horizontal plane? In",
"this referring to the vertical plane or horizontal plane? In other words, if",
"the long side of it printed in the vertical direction or parallel to",
"side of it printed in the vertical direction or parallel to the print",
"vertical plane or horizontal plane? In other words, if I were to print",
"of it printed in the vertical direction or parallel to the print bed?",
"to the vertical plane or horizontal plane? In other words, if I were",
"would I want the long side of it printed in the vertical direction",
"horizontal plane? In other words, if I were to print a rectangular prism,",
"print. Is this referring to the vertical plane or horizontal plane? In other",
"of the print. Is this referring to the vertical plane or horizontal plane?",
"Some filaments suggest \"reducing cross-sectional area\" of the print. Is this referring to",
"referring to the vertical plane or horizontal plane? In other words, if I",
"other words, if I were to print a rectangular prism, would I want",
"to print a rectangular prism, would I want the long side of it",
"\"reducing cross-sectional area\" of the print. Is this referring to the vertical plane",
"plane or horizontal plane? In other words, if I were to print a",
"prism, would I want the long side of it printed in the vertical",
"Is this referring to the vertical plane or horizontal plane? In other words,",
"the vertical plane or horizontal plane? In other words, if I were to",
"long side of it printed in the vertical direction or parallel to the",
"want the long side of it printed in the vertical direction or parallel",
"a rectangular prism, would I want the long side of it printed in"
] |
[
"I made. However, whenever I select it I am only able to select",
"am only able to select the faces or sides. Is there a way",
"made. However, whenever I select it I am only able to select the",
"mirror a triangular prism I made. However, whenever I select it I am",
"to select the faces or sides. Is there a way to select the",
"Is there a way to select the whole 3D object to move or",
"select the faces or sides. Is there a way to select the whole",
"whenever I select it I am only able to select the faces or",
"it I am only able to select the faces or sides. Is there",
"triangular prism I made. However, whenever I select it I am only able",
"select it I am only able to select the faces or sides. Is",
"I am only able to select the faces or sides. Is there a",
"the faces or sides. Is there a way to select the whole 3D",
"like to mirror a triangular prism I made. However, whenever I select it",
"I'd like to mirror a triangular prism I made. However, whenever I select",
"I select it I am only able to select the faces or sides.",
"faces or sides. Is there a way to select the whole 3D object",
"a way to select the whole 3D object to move or mirror it?",
"prism I made. However, whenever I select it I am only able to",
"or sides. Is there a way to select the whole 3D object to",
"there a way to select the whole 3D object to move or mirror",
"able to select the faces or sides. Is there a way to select",
"However, whenever I select it I am only able to select the faces",
"sides. Is there a way to select the whole 3D object to move",
"only able to select the faces or sides. Is there a way to",
"to mirror a triangular prism I made. However, whenever I select it I",
"a triangular prism I made. However, whenever I select it I am only"
] |
[
"in G-code, what is the difference between `Z`- axis and `E`- axis? I",
"When using `G1` command in G-code, what is the difference between `Z`- axis",
"using `G1` command in G-code, what is the difference between `Z`- axis and",
"Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367 F7800.000 G1 E2.00000",
"difference between `Z`- axis and `E`- axis? I see all `E`, `F` and",
"command in G-code, what is the difference between `Z`- axis and `E`- axis?",
"I see all `E`, `F` and `Z` in ``` G1 Z0.350 F7800.000 G1",
"and `Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1",
"see all `E`, `F` and `Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000",
"is the difference between `Z`- axis and `E`- axis? I see all `E`,",
"`F` and `Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0",
"`Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753",
"G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367 F7800.000 G1",
"G-code, what is the difference between `Z`- axis and `E`- axis? I see",
"G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367 F7800.000 G1 E2.00000 F2400.00000 ```",
"in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367",
"and `E`- axis? I see all `E`, `F` and `Z` in ``` G1",
"axis? I see all `E`, `F` and `Z` in ``` G1 Z0.350 F7800.000",
"what is the difference between `Z`- axis and `E`- axis? I see all",
"all `E`, `F` and `Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000",
"`G1` command in G-code, what is the difference between `Z`- axis and `E`-",
"the difference between `Z`- axis and `E`- axis? I see all `E`, `F`",
"`Z`- axis and `E`- axis? I see all `E`, `F` and `Z` in",
"F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367 F7800.000 G1 E2.00000 F2400.00000",
"`E`- axis? I see all `E`, `F` and `Z` in ``` G1 Z0.350",
"axis and `E`- axis? I see all `E`, `F` and `Z` in ```",
"``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92 E0 G1 X96.753 Y95.367 F7800.000",
"between `Z`- axis and `E`- axis? I see all `E`, `F` and `Z`",
"`E`, `F` and `Z` in ``` G1 Z0.350 F7800.000 G1 E-2.00000 F2400.00000 G92"
] |
[
"is proportional to the amount that it cools. If the answer is yes,",
"the filament contracts is proportional to the amount that it cools. If the",
"lower printing temperature might reduce warping-as the temperature interval over which the filament",
"smaller? Or perhaps the difference is negligible? Also, I see a lot of",
"whether the degree to which the filament contracts is proportional to the amount",
"(warping) has been repeatedly addressed on this site. I've just graduated to high-temp",
"much of the physics of this. I'm wondering whether the degree to which",
"this site. I've just graduated to high-temp filaments (PC in particular). I don't",
"degree to which the filament contracts is proportional to the amount that it",
"site. I've just graduated to high-temp filaments (PC in particular). I don't know",
"high-temp filaments (PC in particular). I don't know much of the physics of",
"it suggest that a lower printing temperature might reduce warping-as the temperature interval",
"see a lot of emphasis placed on good first layer adhesion. Is this",
"placed on good first layer adhesion. Is this still an issue if you",
"physics of this. I'm wondering whether the degree to which the filament contracts",
"temperature might reduce warping-as the temperature interval over which the filament cools is",
"I don't know much of the physics of this. I'm wondering whether the",
"(PC in particular). I don't know much of the physics of this. I'm",
"difference is negligible? Also, I see a lot of emphasis placed on good",
"contracts is proportional to the amount that it cools. If the answer is",
"is smaller? Or perhaps the difference is negligible? Also, I see a lot",
"that a lower printing temperature might reduce warping-as the temperature interval over which",
"which the filament cools is smaller? Or perhaps the difference is negligible? Also,",
"emphasis placed on good first layer adhesion. Is this still an issue if",
"repeatedly addressed on this site. I've just graduated to high-temp filaments (PC in",
"realize this issue (warping) has been repeatedly addressed on this site. I've just",
"filament cools is smaller? Or perhaps the difference is negligible? Also, I see",
"interval over which the filament cools is smaller? Or perhaps the difference is",
"might reduce warping-as the temperature interval over which the filament cools is smaller?",
"I've just graduated to high-temp filaments (PC in particular). I don't know much",
"suggest that a lower printing temperature might reduce warping-as the temperature interval over",
"first layer adhesion. Is this still an issue if you are printing on",
"which the filament contracts is proportional to the amount that it cools. If",
"issue (warping) has been repeatedly addressed on this site. I've just graduated to",
"just graduated to high-temp filaments (PC in particular). I don't know much of",
"Also, I see a lot of emphasis placed on good first layer adhesion.",
"a lower printing temperature might reduce warping-as the temperature interval over which the",
"good first layer adhesion. Is this still an issue if you are printing",
"filament contracts is proportional to the amount that it cools. If the answer",
"particular). I don't know much of the physics of this. I'm wondering whether",
"that it cools. If the answer is yes, then wouldn't it suggest that",
"temperature interval over which the filament cools is smaller? Or perhaps the difference",
"been repeatedly addressed on this site. I've just graduated to high-temp filaments (PC",
"is negligible? Also, I see a lot of emphasis placed on good first",
"I realize this issue (warping) has been repeatedly addressed on this site. I've",
"adhesion. Is this still an issue if you are printing on a raft?",
"of this. I'm wondering whether the degree to which the filament contracts is",
"of the physics of this. I'm wondering whether the degree to which the",
"the filament cools is smaller? Or perhaps the difference is negligible? Also, I",
"on this site. I've just graduated to high-temp filaments (PC in particular). I",
"on good first layer adhesion. Is this still an issue if you are",
"addressed on this site. I've just graduated to high-temp filaments (PC in particular).",
"the degree to which the filament contracts is proportional to the amount that",
"perhaps the difference is negligible? Also, I see a lot of emphasis placed",
"of emphasis placed on good first layer adhesion. Is this still an issue",
"then wouldn't it suggest that a lower printing temperature might reduce warping-as the",
"to the amount that it cools. If the answer is yes, then wouldn't",
"cools is smaller? Or perhaps the difference is negligible? Also, I see a",
"this. I'm wondering whether the degree to which the filament contracts is proportional",
"warping-as the temperature interval over which the filament cools is smaller? Or perhaps",
"over which the filament cools is smaller? Or perhaps the difference is negligible?",
"to high-temp filaments (PC in particular). I don't know much of the physics",
"is yes, then wouldn't it suggest that a lower printing temperature might reduce",
"amount that it cools. If the answer is yes, then wouldn't it suggest",
"this issue (warping) has been repeatedly addressed on this site. I've just graduated",
"a lot of emphasis placed on good first layer adhesion. Is this still",
"wondering whether the degree to which the filament contracts is proportional to the",
"I see a lot of emphasis placed on good first layer adhesion. Is",
"graduated to high-temp filaments (PC in particular). I don't know much of the",
"I'm wondering whether the degree to which the filament contracts is proportional to",
"the temperature interval over which the filament cools is smaller? Or perhaps the",
"don't know much of the physics of this. I'm wondering whether the degree",
"If the answer is yes, then wouldn't it suggest that a lower printing",
"the physics of this. I'm wondering whether the degree to which the filament",
"the answer is yes, then wouldn't it suggest that a lower printing temperature",
"proportional to the amount that it cools. If the answer is yes, then",
"filaments (PC in particular). I don't know much of the physics of this.",
"yes, then wouldn't it suggest that a lower printing temperature might reduce warping-as",
"Or perhaps the difference is negligible? Also, I see a lot of emphasis",
"negligible? Also, I see a lot of emphasis placed on good first layer",
"the amount that it cools. If the answer is yes, then wouldn't it",
"answer is yes, then wouldn't it suggest that a lower printing temperature might",
"know much of the physics of this. I'm wondering whether the degree to",
"cools. If the answer is yes, then wouldn't it suggest that a lower",
"reduce warping-as the temperature interval over which the filament cools is smaller? Or",
"the difference is negligible? Also, I see a lot of emphasis placed on",
"wouldn't it suggest that a lower printing temperature might reduce warping-as the temperature",
"layer adhesion. Is this still an issue if you are printing on a",
"has been repeatedly addressed on this site. I've just graduated to high-temp filaments",
"printing temperature might reduce warping-as the temperature interval over which the filament cools",
"to which the filament contracts is proportional to the amount that it cools.",
"in particular). I don't know much of the physics of this. I'm wondering",
"lot of emphasis placed on good first layer adhesion. Is this still an",
"it cools. If the answer is yes, then wouldn't it suggest that a"
] |
[
"decided to print one STL file but the result is not the best",
"Host as the brand recomends, and set all the configuration as the recommended",
"the best one. That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's",
"printer. I'm using Repetier Host as the brand recomends, and set all the",
"is not the best one. That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg)",
"I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the impression. [it",
"have a video of the impression. [it is a G2S pro rostock mini](https://www.youtube.com/watch?v=HDdBQL44R3M)",
"not the best one. That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and",
"using Repetier Host as the brand recomends, and set all the configuration as",
"but the result is not the best one. That's what I was trying",
"what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg)",
"trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you",
"got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the impression. [it is",
"print](https://i.stack.imgur.com/iPEfT.jpg)](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the impression. [it is a G2S",
"recommended one. I decided to print one STL file but the result is",
"best one. That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what",
"the recommended one. I decided to print one STL file but the result",
"Repetier Host as the brand recomends, and set all the configuration as the",
"That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got.",
"one. That's what I was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've",
"I'm using Repetier Host as the brand recomends, and set all the configuration",
"configuration as the recommended one. I decided to print one STL file but",
"3d printer. I'm using Repetier Host as the brand recomends, and set all",
"and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of",
"you have a video of the impression. [it is a G2S pro rostock",
"the configuration as the recommended one. I decided to print one STL file",
"STL file but the result is not the best one. That's what I",
"one. I decided to print one STL file but the result is not",
"and set all the configuration as the recommended one. I decided to print",
"as the recommended one. I decided to print one STL file but the",
"to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have",
"print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a",
"I decided to print one STL file but the result is not the",
"was trying to print: [](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here",
"file but the result is not the best one. That's what I was",
"recomends, and set all the configuration as the recommended one. I decided to",
"what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the impression.",
"my first 3d printer. I'm using Repetier Host as the brand recomends, and",
"[](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the impression. [it is a",
"as the brand recomends, and set all the configuration as the recommended one.",
"set all the configuration as the recommended one. I decided to print one",
"the result is not the best one. That's what I was trying to",
"the brand recomends, and set all the configuration as the recommended one. I",
"all the configuration as the recommended one. I decided to print one STL",
"one STL file but the result is not the best one. That's what",
"[](https://i.stack.imgur.com/f1V22.jpg) and that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video",
"print one STL file but the result is not the best one. That's",
"result is not the best one. That's what I was trying to print:",
"Here you have a video of the impression. [it is a G2S pro",
"That's my first 3d printer. I'm using Repetier Host as the brand recomends,",
"brand recomends, and set all the configuration as the recommended one. I decided",
"that's what I've got. [](https://i.stack.imgur.com/iPEfT.jpg) Here you have a video of the",
"to print one STL file but the result is not the best one.",
"first 3d printer. I'm using Repetier Host as the brand recomends, and set"
] |
[
"printer, but blowing on the print area) could improve the quality of PLA",
"directs air to the hotend, but is it beneficial to add an extra",
"(an) extra fan(s) (not connected to the printer, but blowing on the print",
"with a fan shroud that directs air to the hotend, but is it",
"blowing on the print area) could improve the quality of PLA based prints(printing",
"improve the quality of PLA based prints(printing at 210 C). The printer already",
"could improve the quality of PLA based prints(printing at 210 C). The printer",
"based prints(printing at 210 C). The printer already has a built in fan",
"it beneficial to add an extra fan in order to get better results",
"of PLA based prints(printing at 210 C). The printer already has a built",
"fan in order to get better results on overhangs, fine details, etc, or",
"fan(s) (not connected to the printer, but blowing on the print area) could",
"has a built in fan with a fan shroud that directs air to",
"but is it beneficial to add an extra fan in order to get",
"adding (an) extra fan(s) (not connected to the printer, but blowing on the",
"on overhangs, fine details, etc, or does extra cooling negatively/not affect print quality?",
"air to the hotend, but is it beneficial to add an extra fan",
"fan shroud that directs air to the hotend, but is it beneficial to",
"a built in fan with a fan shroud that directs air to the",
"an extra fan in order to get better results on overhangs, fine details,",
"hotend, but is it beneficial to add an extra fan in order to",
"C). The printer already has a built in fan with a fan shroud",
"PLA based prints(printing at 210 C). The printer already has a built in",
"area) could improve the quality of PLA based prints(printing at 210 C). The",
"but blowing on the print area) could improve the quality of PLA based",
"The printer already has a built in fan with a fan shroud that",
"wondering if adding (an) extra fan(s) (not connected to the printer, but blowing",
"to get better results on overhangs, fine details, etc, or does extra cooling",
"print area) could improve the quality of PLA based prints(printing at 210 C).",
"beneficial to add an extra fan in order to get better results on",
"on the print area) could improve the quality of PLA based prints(printing at",
"printer already has a built in fan with a fan shroud that directs",
"to add an extra fan in order to get better results on overhangs,",
"extra fan(s) (not connected to the printer, but blowing on the print area)",
"I was wondering if adding (an) extra fan(s) (not connected to the printer,",
"add an extra fan in order to get better results on overhangs, fine",
"a fan shroud that directs air to the hotend, but is it beneficial",
"extra fan in order to get better results on overhangs, fine details, etc,",
"the quality of PLA based prints(printing at 210 C). The printer already has",
"get better results on overhangs, fine details, etc, or does extra cooling negatively/not",
"shroud that directs air to the hotend, but is it beneficial to add",
"was wondering if adding (an) extra fan(s) (not connected to the printer, but",
"to the hotend, but is it beneficial to add an extra fan in",
"better results on overhangs, fine details, etc, or does extra cooling negatively/not affect",
"210 C). The printer already has a built in fan with a fan",
"already has a built in fan with a fan shroud that directs air",
"order to get better results on overhangs, fine details, etc, or does extra",
"in fan with a fan shroud that directs air to the hotend, but",
"if adding (an) extra fan(s) (not connected to the printer, but blowing on",
"the hotend, but is it beneficial to add an extra fan in order",
"the printer, but blowing on the print area) could improve the quality of",
"to the printer, but blowing on the print area) could improve the quality",
"results on overhangs, fine details, etc, or does extra cooling negatively/not affect print",
"built in fan with a fan shroud that directs air to the hotend,",
"prints(printing at 210 C). The printer already has a built in fan with",
"quality of PLA based prints(printing at 210 C). The printer already has a",
"in order to get better results on overhangs, fine details, etc, or does",
"fan with a fan shroud that directs air to the hotend, but is",
"at 210 C). The printer already has a built in fan with a",
"the print area) could improve the quality of PLA based prints(printing at 210",
"connected to the printer, but blowing on the print area) could improve the",
"is it beneficial to add an extra fan in order to get better",
"(not connected to the printer, but blowing on the print area) could improve",
"that directs air to the hotend, but is it beneficial to add an"
] |
[
"putting out any plastic. I replaced the nozzle with a 0.2 mm one",
"But nothing helped it keeps making this waves. At the old 0.4 mm",
"any plastic. I replaced the nozzle with a 0.2 mm one and now",
"The problem was that the nozzle with a 0.4 mm diameter wasn't putting",
"and speed. But nothing helped it keeps making this waves. At the old",
"tried to change flow,temperatures and speed. But nothing helped it keeps making this",
"the nozzle with a 0.4 mm diameter wasn't putting out any plastic. I",
"was that the nozzle with a 0.4 mm diameter wasn't putting out any",
"change flow,temperatures and speed. But nothing helped it keeps making this waves. At",
"of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures",
"the nozzle with a 0.2 mm one and now the bottom of my",
"wasn't putting out any plastic. I replaced the nozzle with a 0.2 mm",
"with a 0.4 mm diameter wasn't putting out any plastic. I replaced the",
"the bottom of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to",
"flow,temperatures and speed. But nothing helped it keeps making this waves. At the",
"nozzle with a 0.4 mm diameter wasn't putting out any plastic. I replaced",
"I replaced the nozzle with a 0.2 mm one and now the bottom",
"0.2 mm one and now the bottom of my model is looking like",
"helped it keeps making this waves. At the old 0.4 mm nozzle there",
"diameter wasn't putting out any plastic. I replaced the nozzle with a 0.2",
"bottom of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change",
"like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed. But nothing helped",
"with my nozzle on my homemade printer. The problem was that the nozzle",
"had a problem with my nozzle on my homemade printer. The problem was",
"my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and",
"replaced the nozzle with a 0.2 mm one and now the bottom of",
"model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed.",
"problem with my nozzle on my homemade printer. The problem was that the",
"I tried to change flow,temperatures and speed. But nothing helped it keeps making",
"making this waves. At the old 0.4 mm nozzle there everything was okay.",
"homemade printer. The problem was that the nozzle with a 0.4 mm diameter",
"out any plastic. I replaced the nozzle with a 0.2 mm one and",
"nothing helped it keeps making this waves. At the old 0.4 mm nozzle",
"I had a problem with my nozzle on my homemade printer. The problem",
"keeps making this waves. At the old 0.4 mm nozzle there everything was",
"on my homemade printer. The problem was that the nozzle with a 0.4",
"one and now the bottom of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg)",
"with a 0.2 mm one and now the bottom of my model is",
"plastic. I replaced the nozzle with a 0.2 mm one and now the",
"a 0.4 mm diameter wasn't putting out any plastic. I replaced the nozzle",
"printer. The problem was that the nozzle with a 0.4 mm diameter wasn't",
"and now the bottom of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I",
"mm diameter wasn't putting out any plastic. I replaced the nozzle with a",
"now the bottom of my model is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried",
"speed. But nothing helped it keeps making this waves. At the old 0.4",
"0.4 mm diameter wasn't putting out any plastic. I replaced the nozzle with",
"problem was that the nozzle with a 0.4 mm diameter wasn't putting out",
"is looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed. But",
"my homemade printer. The problem was that the nozzle with a 0.4 mm",
"nozzle with a 0.2 mm one and now the bottom of my model",
"nozzle on my homemade printer. The problem was that the nozzle with a",
"it keeps making this waves. At the old 0.4 mm nozzle there everything",
"to change flow,temperatures and speed. But nothing helped it keeps making this waves.",
"looking like this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed. But nothing",
"mm one and now the bottom of my model is looking like this:",
"this: [](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed. But nothing helped it",
"that the nozzle with a 0.4 mm diameter wasn't putting out any plastic.",
"my nozzle on my homemade printer. The problem was that the nozzle with",
"[](https://i.stack.imgur.com/UFSHV.jpg) I tried to change flow,temperatures and speed. But nothing helped it keeps",
"a problem with my nozzle on my homemade printer. The problem was that",
"a 0.2 mm one and now the bottom of my model is looking"
] |
[
"still warped I read up on how to fix, but most covered how",
"anything, and I am using it with the stock program (makerbot print). Otherwise,",
"so I shrunk to just a small area, but It still warped I",
"it with the stock program (makerbot print). Otherwise, I am using it as",
"models that covered the whole tray, so I shrunk to just a small",
"lower the temp, would that work? smart extruder at default settings, 215 C.",
"to just a small area, but It still warped I read up on",
"at default settings, 215 C. The printer does not have a heated base,",
"have I treated it with anything, and I am using it with the",
"doing a bunch of models that covered the whole tray, so I shrunk",
"would that work? smart extruder at default settings, 215 C. The printer does",
"any of the terminology On a replicator+, I have been printing successfully for",
"base, nor have I treated it with anything, and I am using it",
"not have a heated base, nor have I treated it with anything, and",
"printing successfully for a while, when suddenly the raft started to warp. I",
"I misuse any of the terminology On a replicator+, I have been printing",
"treated it with anything, and I am using it with the stock program",
"how to fix warping in the model itself, not the rafting. Some said",
"temp, would that work? smart extruder at default settings, 215 C. The printer",
"I have been printing successfully for a while, when suddenly the raft started",
"rafting. Some said to lower the temp, would that work? smart extruder at",
"fix warping in the model itself, not the rafting. Some said to lower",
"replicator+, I have been printing successfully for a while, when suddenly the raft",
"stock program (makerbot print). Otherwise, I am using it as it came out",
"warped I read up on how to fix, but most covered how to",
"that work? smart extruder at default settings, 215 C. The printer does not",
"The printer does not have a heated base, nor have I treated it",
"a bunch of models that covered the whole tray, so I shrunk to",
"shrunk to just a small area, but It still warped I read up",
"but most covered how to fix warping in the model itself, not the",
"successfully for a while, when suddenly the raft started to warp. I was",
"just a small area, but It still warped I read up on how",
"settings, 215 C. The printer does not have a heated base, nor have",
"Quick thing: Please tell me if I misuse any of the terminology On",
"started to warp. I was doing a bunch of models that covered the",
"the temp, would that work? smart extruder at default settings, 215 C. The",
"extruder at default settings, 215 C. The printer does not have a heated",
"bunch of models that covered the whole tray, so I shrunk to just",
"printer does not have a heated base, nor have I treated it with",
"the rafting. Some said to lower the temp, would that work? smart extruder",
"of models that covered the whole tray, so I shrunk to just a",
"whole tray, so I shrunk to just a small area, but It still",
"smart extruder at default settings, 215 C. The printer does not have a",
"default settings, 215 C. The printer does not have a heated base, nor",
"misuse any of the terminology On a replicator+, I have been printing successfully",
"that covered the whole tray, so I shrunk to just a small area,",
"with anything, and I am using it with the stock program (makerbot print).",
"read up on how to fix, but most covered how to fix warping",
"was doing a bunch of models that covered the whole tray, so I",
"the raft started to warp. I was doing a bunch of models that",
"print). Otherwise, I am using it as it came out of the box.",
"tray, so I shrunk to just a small area, but It still warped",
"I treated it with anything, and I am using it with the stock",
"small area, but It still warped I read up on how to fix,",
"to fix warping in the model itself, not the rafting. Some said to",
"215 C. The printer does not have a heated base, nor have I",
"does not have a heated base, nor have I treated it with anything,",
"a replicator+, I have been printing successfully for a while, when suddenly the",
"a heated base, nor have I treated it with anything, and I am",
"C. The printer does not have a heated base, nor have I treated",
"Otherwise, I am using it as it came out of the box. [](https://i.stack.imgur.com/1k0PE.jpg)",
"but It still warped I read up on how to fix, but most",
"have been printing successfully for a while, when suddenly the raft started to",
"covered how to fix warping in the model itself, not the rafting. Some",
"to lower the temp, would that work? smart extruder at default settings, 215",
"(makerbot print). Otherwise, I am using it as it came out of the",
"of the terminology On a replicator+, I have been printing successfully for a",
"for a while, when suddenly the raft started to warp. I was doing",
"and I am using it with the stock program (makerbot print). Otherwise, I",
"it with anything, and I am using it with the stock program (makerbot",
"I shrunk to just a small area, but It still warped I read",
"up on how to fix, but most covered how to fix warping in",
"how to fix, but most covered how to fix warping in the model",
"program (makerbot print). Otherwise, I am using it as it came out of",
"Please tell me if I misuse any of the terminology On a replicator+,",
"the whole tray, so I shrunk to just a small area, but It",
"I read up on how to fix, but most covered how to fix",
"fix, but most covered how to fix warping in the model itself, not",
"nor have I treated it with anything, and I am using it with",
"the stock program (makerbot print). Otherwise, I am using it as it came",
"not the rafting. Some said to lower the temp, would that work? smart",
"Some said to lower the temp, would that work? smart extruder at default",
"a while, when suddenly the raft started to warp. I was doing a",
"to warp. I was doing a bunch of models that covered the whole",
"to fix, but most covered how to fix warping in the model itself,",
"when suddenly the raft started to warp. I was doing a bunch of",
"model itself, not the rafting. Some said to lower the temp, would that",
"I am using it with the stock program (makerbot print). Otherwise, I am",
"tell me if I misuse any of the terminology On a replicator+, I",
"the model itself, not the rafting. Some said to lower the temp, would",
"said to lower the temp, would that work? smart extruder at default settings,",
"It still warped I read up on how to fix, but most covered",
"am using it with the stock program (makerbot print). Otherwise, I am using",
"warp. I was doing a bunch of models that covered the whole tray,",
"warping in the model itself, not the rafting. Some said to lower the",
"On a replicator+, I have been printing successfully for a while, when suddenly",
"work? smart extruder at default settings, 215 C. The printer does not have",
"thing: Please tell me if I misuse any of the terminology On a",
"covered the whole tray, so I shrunk to just a small area, but",
"on how to fix, but most covered how to fix warping in the",
"if I misuse any of the terminology On a replicator+, I have been",
"itself, not the rafting. Some said to lower the temp, would that work?",
"suddenly the raft started to warp. I was doing a bunch of models",
"heated base, nor have I treated it with anything, and I am using",
"using it with the stock program (makerbot print). Otherwise, I am using it",
"most covered how to fix warping in the model itself, not the rafting.",
"in the model itself, not the rafting. Some said to lower the temp,",
"with the stock program (makerbot print). Otherwise, I am using it as it",
"the terminology On a replicator+, I have been printing successfully for a while,",
"area, but It still warped I read up on how to fix, but",
"while, when suddenly the raft started to warp. I was doing a bunch",
"have a heated base, nor have I treated it with anything, and I",
"terminology On a replicator+, I have been printing successfully for a while, when",
"been printing successfully for a while, when suddenly the raft started to warp.",
"raft started to warp. I was doing a bunch of models that covered",
"a small area, but It still warped I read up on how to",
"I was doing a bunch of models that covered the whole tray, so",
"me if I misuse any of the terminology On a replicator+, I have"
] |
[
"when plugged in it went to 18 °C. Is it the motherboard? How",
"have plans to install on) Upon further investigation, I tested the mother board",
"it was at 18 °C. I did try moving the pins, and that",
"to 50 °C, but it was at 18 °C. I did try moving",
"is not loose (very simple thing to try). I want to know what",
"°C, but it was at 18 °C. I did try moving the pins,",
"plans to install on) Upon further investigation, I tested the mother board for",
"what to look for when I try to fix the heat bed. Please",
"and that is not loose (very simple thing to try). I want to",
"up and there is nothing. I had the printer trying to heat the",
"done the bed was not on anymore. The display said it was set",
"was at 18 °C. I did try moving the pins, and that is",
"loose (very simple thing to try). I want to know what could have",
"the pins, and that is not loose (very simple thing to try). I",
"set to 50 °C, but it was at 18 °C. I did try",
"testing. But the thermistor is working, when I unhooked the connection the thermistor",
"to 0 °C, when plugged in it went to 18 °C. Is it",
"this knowing no power is being supplied to the bed from the motherboard?",
"on anymore. The display said it was set to 50 °C, but it",
"stopped working. It was fine up to 75 % of the print, then",
"want to know what could have happened and what to look for when",
"there is nothing. I had the printer trying to heat the bed when",
"when I try to fix the heat bed. Please note: I do have",
"when I unhooked the connection the thermistor went to 0 °C, when plugged",
"°C. Is it the motherboard? How can I fix this knowing no power",
"anymore. The display said it was set to 50 °C, but it was",
"then when it was done the bed was not on anymore. The display",
"of the print, then when it was done the bed was not on",
"to 18 °C. Is it the motherboard? How can I fix this knowing",
"but it was at 18 °C. I did try moving the pins, and",
"MOSFET (I do have plans to install on) Upon further investigation, I tested",
"note: I do have a multi-meter. I do not use a MOSFET (I",
"the thermistor went to 0 °C, when plugged in it went to 18",
"plugged in it went to 18 °C. Is it the motherboard? How can",
"The display said it was set to 50 °C, but it was at",
"install on) Upon further investigation, I tested the mother board for any voltage",
"when I was testing. But the thermistor is working, when I unhooked the",
"and what to look for when I try to fix the heat bed.",
"bed stopped working. It was fine up to 75 % of the print,",
"% of the print, then when it was done the bed was not",
"I tested the mother board for any voltage were the bed hooks up",
"a multi-meter. I do not use a MOSFET (I do have plans to",
"printer trying to heat the bed when I was testing. But the thermistor",
"I try to fix the heat bed. Please note: I do have a",
"Is it the motherboard? How can I fix this knowing no power is",
"75 % of the print, then when it was done the bed was",
"up to 75 % of the print, then when it was done the",
"can I fix this knowing no power is being supplied to the bed",
"trying to heat the bed when I was testing. But the thermistor is",
"the bed was not on anymore. The display said it was set to",
"had the printer trying to heat the bed when I was testing. But",
"fine up to 75 % of the print, then when it was done",
"°C. I did try moving the pins, and that is not loose (very",
"I was testing. But the thermistor is working, when I unhooked the connection",
"were the bed hooks up and there is nothing. I had the printer",
"I had the printer trying to heat the bed when I was testing.",
"is working, when I unhooked the connection the thermistor went to 0 °C,",
"to know what could have happened and what to look for when I",
"not use a MOSFET (I do have plans to install on) Upon further",
"is nothing. I had the printer trying to heat the bed when I",
"night the heat bed stopped working. It was fine up to 75 %",
"nothing. I had the printer trying to heat the bed when I was",
"tested the mother board for any voltage were the bed hooks up and",
"simple thing to try). I want to know what could have happened and",
"working. It was fine up to 75 % of the print, then when",
"use a MOSFET (I do have plans to install on) Upon further investigation,",
"the mother board for any voltage were the bed hooks up and there",
"and there is nothing. I had the printer trying to heat the bed",
"unhooked the connection the thermistor went to 0 °C, when plugged in it",
"knowing no power is being supplied to the bed from the motherboard? Do",
"it the motherboard? How can I fix this knowing no power is being",
"was not on anymore. The display said it was set to 50 °C,",
"at 18 °C. I did try moving the pins, and that is not",
"18 °C. I did try moving the pins, and that is not loose",
"thing to try). I want to know what could have happened and what",
"the heat bed stopped working. It was fine up to 75 % of",
"do have a multi-meter. I do not use a MOSFET (I do have",
"the bed hooks up and there is nothing. I had the printer trying",
"hooks up and there is nothing. I had the printer trying to heat",
"in it went to 18 °C. Is it the motherboard? How can I",
"happened and what to look for when I try to fix the heat",
"Please note: I do have a multi-meter. I do not use a MOSFET",
"working, when I unhooked the connection the thermistor went to 0 °C, when",
"°C, when plugged in it went to 18 °C. Is it the motherboard?",
"was testing. But the thermistor is working, when I unhooked the connection the",
"50 °C, but it was at 18 °C. I did try moving the",
"that is not loose (very simple thing to try). I want to know",
"I fix this knowing no power is being supplied to the bed from",
"the print, then when it was done the bed was not on anymore.",
"do have plans to install on) Upon further investigation, I tested the mother",
"to look for when I try to fix the heat bed. Please note:",
"for when I try to fix the heat bed. Please note: I do",
"(I do have plans to install on) Upon further investigation, I tested the",
"further investigation, I tested the mother board for any voltage were the bed",
"mother board for any voltage were the bed hooks up and there is",
"Just last night the heat bed stopped working. It was fine up to",
"heat bed. Please note: I do have a multi-meter. I do not use",
"have a multi-meter. I do not use a MOSFET (I do have plans",
"not loose (very simple thing to try). I want to know what could",
"it was done the bed was not on anymore. The display said it",
"to install on) Upon further investigation, I tested the mother board for any",
"went to 18 °C. Is it the motherboard? How can I fix this",
"18 °C. Is it the motherboard? How can I fix this knowing no",
"board for any voltage were the bed hooks up and there is nothing.",
"not on anymore. The display said it was set to 50 °C, but",
"it went to 18 °C. Is it the motherboard? How can I fix",
"on) Upon further investigation, I tested the mother board for any voltage were",
"know what could have happened and what to look for when I try",
"motherboard? How can I fix this knowing no power is being supplied to",
"the heat bed. Please note: I do have a multi-meter. I do not",
"investigation, I tested the mother board for any voltage were the bed hooks",
"when it was done the bed was not on anymore. The display said",
"bed was not on anymore. The display said it was set to 50",
"print, then when it was done the bed was not on anymore. The",
"the thermistor is working, when I unhooked the connection the thermistor went to",
"have happened and what to look for when I try to fix the",
"any voltage were the bed hooks up and there is nothing. I had",
"do not use a MOSFET (I do have plans to install on) Upon",
"to heat the bed when I was testing. But the thermistor is working,",
"How can I fix this knowing no power is being supplied to the",
"I want to know what could have happened and what to look for",
"what could have happened and what to look for when I try to",
"the bed when I was testing. But the thermistor is working, when I",
"is being supplied to the bed from the motherboard? Do I need a",
"I did try moving the pins, and that is not loose (very simple",
"moving the pins, and that is not loose (very simple thing to try).",
"display said it was set to 50 °C, but it was at 18",
"fix this knowing no power is being supplied to the bed from the",
"I unhooked the connection the thermistor went to 0 °C, when plugged in",
"it was set to 50 °C, but it was at 18 °C. I",
"voltage were the bed hooks up and there is nothing. I had the",
"power is being supplied to the bed from the motherboard? Do I need",
"thermistor is working, when I unhooked the connection the thermistor went to 0",
"try). I want to know what could have happened and what to look",
"I do not use a MOSFET (I do have plans to install on)",
"to 75 % of the print, then when it was done the bed",
"to fix the heat bed. Please note: I do have a multi-meter. I",
"bed. Please note: I do have a multi-meter. I do not use a",
"for any voltage were the bed hooks up and there is nothing. I",
"(very simple thing to try). I want to know what could have happened",
"did try moving the pins, and that is not loose (very simple thing",
"bed when I was testing. But the thermistor is working, when I unhooked",
"But the thermistor is working, when I unhooked the connection the thermistor went",
"was fine up to 75 % of the print, then when it was",
"the motherboard? How can I fix this knowing no power is being supplied",
"try moving the pins, and that is not loose (very simple thing to",
"could have happened and what to look for when I try to fix",
"no power is being supplied to the bed from the motherboard? Do I",
"heat the bed when I was testing. But the thermistor is working, when",
"being supplied to the bed from the motherboard? Do I need a new",
"I do have a multi-meter. I do not use a MOSFET (I do",
"was done the bed was not on anymore. The display said it was",
"multi-meter. I do not use a MOSFET (I do have plans to install",
"to try). I want to know what could have happened and what to",
"the connection the thermistor went to 0 °C, when plugged in it went",
"said it was set to 50 °C, but it was at 18 °C.",
"supplied to the bed from the motherboard? Do I need a new motherboard?",
"the printer trying to heat the bed when I was testing. But the",
"bed hooks up and there is nothing. I had the printer trying to",
"0 °C, when plugged in it went to 18 °C. Is it the",
"fix the heat bed. Please note: I do have a multi-meter. I do",
"thermistor went to 0 °C, when plugged in it went to 18 °C.",
"It was fine up to 75 % of the print, then when it",
"pins, and that is not loose (very simple thing to try). I want",
"last night the heat bed stopped working. It was fine up to 75",
"Upon further investigation, I tested the mother board for any voltage were the",
"went to 0 °C, when plugged in it went to 18 °C. Is",
"a MOSFET (I do have plans to install on) Upon further investigation, I",
"was set to 50 °C, but it was at 18 °C. I did",
"connection the thermistor went to 0 °C, when plugged in it went to",
"try to fix the heat bed. Please note: I do have a multi-meter.",
"look for when I try to fix the heat bed. Please note: I",
"heat bed stopped working. It was fine up to 75 % of the"
] |
[
"values for Ultimaker Kp 22.2, Ki 1.08, Kd 144. I have tried to",
"every time I run it and using the results gave worse results (sometimes",
"temps. Second is trying to do a PID tune. Third and fourth are",
"Using marlin 1.1x and Its possible I have something configured incorrectly. I can",
"using the results gave worse results (sometimes giving a heating error during the",
"error during the autotune). I checked all the wiring and nothing looks frayed",
"I recently rebuilt my A8 printer to have a metal frame and replaced",
"different values every time I run it and using the results gave worse",
"a heating error during the autotune). I checked all the wiring and nothing",
"sometimes I get thermal runaway during a print. Both cold and at temp",
"but get drastically different values every time I run it and using the",
"(sometimes giving a heating error during the autotune). I checked all the wiring",
"both my hotend and hotbed. Using marlin 1.1x and Its possible I have",
"readings from both my hotend and hotbed. Using marlin 1.1x and Its possible",
"autotune but get drastically different values every time I run it and using",
"temp (200c) have fairly large temp spikes. I didn't have this problem with",
"frayed or damaged. First pic is cold temps. Second is trying to do",
"but sometimes I get thermal runaway during a print. Both cold and at",
"Kp 22.2, Ki 1.08, Kd 144. I have tried to use PID autotune",
"something configured incorrectly. I can get successful prints with good quality but sometimes",
"this problem with my old board. I had much smoother temp curves. I'm",
"incorrectly. I can get successful prints with good quality but sometimes I get",
"much smoother temp curves. I'm using the default PID values for Ultimaker Kp",
"values every time I run it and using the results gave worse results",
"giving a heating error during the autotune). I checked all the wiring and",
"have a metal frame and replaced the board with a GT2560 reva+. I'm",
"during the autotune). I checked all the wiring and nothing looks frayed or",
"my A8 printer to have a metal frame and replaced the board with",
"curves. I'm using the default PID values for Ultimaker Kp 22.2, Ki 1.08,",
"runaway during a print. Both cold and at temp (200c) have fairly large",
"fourth are during a print. [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/A9bU0.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/A9bU0.png) [](https://i.stack.imgur.com/GwyP4.png)",
"the results gave worse results (sometimes giving a heating error during the autotune).",
"cold and at temp (200c) have fairly large temp spikes. I didn't have",
"First pic is cold temps. Second is trying to do a PID tune.",
"board. I had much smoother temp curves. I'm using the default PID values",
"thermal runaway during a print. Both cold and at temp (200c) have fairly",
"possible I have something configured incorrectly. I can get successful prints with good",
"with the temp readings from both my hotend and hotbed. Using marlin 1.1x",
"PID autotune but get drastically different values every time I run it and",
"Ki 1.08, Kd 144. I have tried to use PID autotune but get",
"Third and fourth are during a print. [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/A9bU0.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png)",
"and replaced the board with a GT2560 reva+. I'm having problems with the",
"configured incorrectly. I can get successful prints with good quality but sometimes I",
"successful prints with good quality but sometimes I get thermal runaway during a",
"drastically different values every time I run it and using the results gave",
"hotbed. Using marlin 1.1x and Its possible I have something configured incorrectly. I",
"1.08, Kd 144. I have tried to use PID autotune but get drastically",
"heating error during the autotune). I checked all the wiring and nothing looks",
"and hotbed. Using marlin 1.1x and Its possible I have something configured incorrectly.",
"damaged. First pic is cold temps. Second is trying to do a PID",
"didn't have this problem with my old board. I had much smoother temp",
"and using the results gave worse results (sometimes giving a heating error during",
"1.1x and Its possible I have something configured incorrectly. I can get successful",
"I didn't have this problem with my old board. I had much smoother",
"I get thermal runaway during a print. Both cold and at temp (200c)",
"trying to do a PID tune. Third and fourth are during a print.",
"do a PID tune. Third and fourth are during a print. [](https://i.stack.imgur.com/7H8KC.png)",
"looks frayed or damaged. First pic is cold temps. Second is trying to",
"it and using the results gave worse results (sometimes giving a heating error",
"a PID tune. Third and fourth are during a print. [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/A9bU0.png) [](https://i.stack.imgur.com/7H8KC.png) [](https://i.stack.imgur.com/EpW8E.png) [](https://i.stack.imgur.com/A9bU0.png)",
"with good quality but sometimes I get thermal runaway during a print. Both",
"large temp spikes. I didn't have this problem with my old board. I",
"prints with good quality but sometimes I get thermal runaway during a print.",
"I had much smoother temp curves. I'm using the default PID values for",
"worse results (sometimes giving a heating error during the autotune). I checked all",
"during a print. Both cold and at temp (200c) have fairly large temp"
] |
[
"glue stick. What can I do to keep the plastic sticking to the",
"I am having the PLA lift around the edges which I have NEVER",
"the bed during print. I will note that the lift is not super",
"than the glue stick. What can I do to keep the plastic sticking",
"NEVER experienced. The glue is not helping like it did with the heat.",
"time to try and fix it and I am trying to print something",
"Right now my heated bed is down and I had no time to",
"it was not that much better than the glue stick. What can I",
"the masking tape I use, heard that helps and it was not that",
"The glue is not helping like it did with the heat. And I",
"I have NEVER experienced. The glue is not helping like it did with",
"tape I use, heard that helps and it was not that much better",
"to print something for a friend. I am having the PLA lift around",
"not that much better than the glue stick. What can I do to",
"down and I had no time to try and fix it and I",
"had no time to try and fix it and I am trying to",
"that helps and it was not that much better than the glue stick.",
"also tried rubbing alcohol on the masking tape I use, heard that helps",
"helps and it was not that much better than the glue stick. What",
"that much better than the glue stick. What can I do to keep",
"bed is down and I had no time to try and fix it",
"something for a friend. I am having the PLA lift around the edges",
"heard that helps and it was not that much better than the glue",
"What can I do to keep the plastic sticking to the bed during",
"friend. I am having the PLA lift around the edges which I have",
"now my heated bed is down and I had no time to try",
"having the PLA lift around the edges which I have NEVER experienced. The",
"trying to print something for a friend. I am having the PLA lift",
"it did with the heat. And I also tried rubbing alcohol on the",
"around the edges which I have NEVER experienced. The glue is not helping",
"do to keep the plastic sticking to the bed during print. I will",
"to keep the plastic sticking to the bed during print. I will note",
"I will note that the lift is not super bad, but I do",
"note that the lift is not super bad, but I do like the",
"rubbing alcohol on the masking tape I use, heard that helps and it",
"keep the plastic sticking to the bed during print. I will note that",
"that the lift is not super bad, but I do like the littlest",
"masking tape I use, heard that helps and it was not that much",
"is not super bad, but I do like the littlest of lift on",
"with the heat. And I also tried rubbing alcohol on the masking tape",
"the heat. And I also tried rubbing alcohol on the masking tape I",
"and it was not that much better than the glue stick. What can",
"to the bed during print. I will note that the lift is not",
"fix it and I am trying to print something for a friend. I",
"a friend. I am having the PLA lift around the edges which I",
"heat. And I also tried rubbing alcohol on the masking tape I use,",
"during print. I will note that the lift is not super bad, but",
"is not helping like it did with the heat. And I also tried",
"will note that the lift is not super bad, but I do like",
"like it did with the heat. And I also tried rubbing alcohol on",
"edges which I have NEVER experienced. The glue is not helping like it",
"much better than the glue stick. What can I do to keep the",
"And I also tried rubbing alcohol on the masking tape I use, heard",
"print. I will note that the lift is not super bad, but I",
"better than the glue stick. What can I do to keep the plastic",
"and I had no time to try and fix it and I am",
"can I do to keep the plastic sticking to the bed during print.",
"no time to try and fix it and I am trying to print",
"and fix it and I am trying to print something for a friend.",
"tried rubbing alcohol on the masking tape I use, heard that helps and",
"alcohol on the masking tape I use, heard that helps and it was",
"it and I am trying to print something for a friend. I am",
"experienced. The glue is not helping like it did with the heat. And",
"on the masking tape I use, heard that helps and it was not",
"to try and fix it and I am trying to print something for",
"was not that much better than the glue stick. What can I do",
"lift is not super bad, but I do like the littlest of lift",
"I use, heard that helps and it was not that much better than",
"super bad, but I do like the littlest of lift on any print.",
"and I am trying to print something for a friend. I am having",
"try and fix it and I am trying to print something for a",
"PLA lift around the edges which I have NEVER experienced. The glue is",
"not helping like it did with the heat. And I also tried rubbing",
"am having the PLA lift around the edges which I have NEVER experienced.",
"heated bed is down and I had no time to try and fix",
"use, heard that helps and it was not that much better than the",
"for a friend. I am having the PLA lift around the edges which",
"the glue stick. What can I do to keep the plastic sticking to",
"bed during print. I will note that the lift is not super bad,",
"sticking to the bed during print. I will note that the lift is",
"which I have NEVER experienced. The glue is not helping like it did",
"have NEVER experienced. The glue is not helping like it did with the",
"I also tried rubbing alcohol on the masking tape I use, heard that",
"helping like it did with the heat. And I also tried rubbing alcohol",
"stick. What can I do to keep the plastic sticking to the bed",
"not super bad, but I do like the littlest of lift on any",
"am trying to print something for a friend. I am having the PLA",
"glue is not helping like it did with the heat. And I also",
"is down and I had no time to try and fix it and",
"I am trying to print something for a friend. I am having the",
"the plastic sticking to the bed during print. I will note that the",
"the edges which I have NEVER experienced. The glue is not helping like",
"I do to keep the plastic sticking to the bed during print. I",
"the PLA lift around the edges which I have NEVER experienced. The glue",
"my heated bed is down and I had no time to try and",
"did with the heat. And I also tried rubbing alcohol on the masking",
"I had no time to try and fix it and I am trying",
"the lift is not super bad, but I do like the littlest of",
"lift around the edges which I have NEVER experienced. The glue is not",
"print something for a friend. I am having the PLA lift around the",
"plastic sticking to the bed during print. I will note that the lift"
] |
[
"I have a few strands. Would it be possible to mend the ends",
"melted together and after cutting I have a few strands. Would it be",
"filament had a tangle and got pulled into the printer head. Some got",
"my spool of filament had a tangle and got pulled into the printer",
"few strands. Would it be possible to mend the ends together to make",
"I am wondering if it can be done. So my spool of filament",
"spool of filament had a tangle and got pulled into the printer head.",
"and after cutting I have a few strands. Would it be possible to",
"into the printer head. Some got melted together and after cutting I have",
"of filament had a tangle and got pulled into the printer head. Some",
"it can be done. So my spool of filament had a tangle and",
"to mend the ends together to make one continuous strand instead of many",
"got pulled into the printer head. Some got melted together and after cutting",
"and got pulled into the printer head. Some got melted together and after",
"While I don't think this is easily possible I am wondering if it",
"be possible to mend the ends together to make one continuous strand instead",
"pulled into the printer head. Some got melted together and after cutting I",
"a tangle and got pulled into the printer head. Some got melted together",
"So my spool of filament had a tangle and got pulled into the",
"possible I am wondering if it can be done. So my spool of",
"Would it be possible to mend the ends together to make one continuous",
"be done. So my spool of filament had a tangle and got pulled",
"is easily possible I am wondering if it can be done. So my",
"cutting I have a few strands. Would it be possible to mend the",
"together and after cutting I have a few strands. Would it be possible",
"easily possible I am wondering if it can be done. So my spool",
"think this is easily possible I am wondering if it can be done.",
"it be possible to mend the ends together to make one continuous strand",
"am wondering if it can be done. So my spool of filament had",
"a few strands. Would it be possible to mend the ends together to",
"done. So my spool of filament had a tangle and got pulled into",
"this is easily possible I am wondering if it can be done. So",
"had a tangle and got pulled into the printer head. Some got melted",
"don't think this is easily possible I am wondering if it can be",
"head. Some got melted together and after cutting I have a few strands.",
"if it can be done. So my spool of filament had a tangle",
"printer head. Some got melted together and after cutting I have a few",
"strands. Would it be possible to mend the ends together to make one",
"I don't think this is easily possible I am wondering if it can",
"Some got melted together and after cutting I have a few strands. Would",
"got melted together and after cutting I have a few strands. Would it",
"wondering if it can be done. So my spool of filament had a",
"tangle and got pulled into the printer head. Some got melted together and",
"have a few strands. Would it be possible to mend the ends together",
"mend the ends together to make one continuous strand instead of many small",
"after cutting I have a few strands. Would it be possible to mend",
"the ends together to make one continuous strand instead of many small strand?",
"can be done. So my spool of filament had a tangle and got",
"the printer head. Some got melted together and after cutting I have a",
"possible to mend the ends together to make one continuous strand instead of"
] |
[
"(basically an open cube with 4 bottom layers). The wall width I measured",
"flow compensation parameters. I am using a 0.4 mm nozzle and therefore set",
"of fine-tuning my cheap CTC i3 clone. I'm using Cura 3.1 for slicing.",
"I got from this was 0.45 mm, which is much better than before.",
"The wall width I got from this was 0.45 mm, which is much",
"not touch, so the print is not watertight. Up to now I assumed",
"before. There is only one problem: the parallel lines in the four bottom",
"width I got from this was 0.45 mm, which is much better than",
"the print is not watertight. Up to now I assumed that Cura would",
"in Cura. I then printed a cube with 0% infill, 1 wall line",
"wall width I measured on the printed result is 0.52 mm. To correct",
"cheap CTC i3 clone. I'm using Cura 3.1 for slicing. After calibrating the",
"Up to now I assumed that Cura would calculate the distance between the",
"extruder steps, I wanted to optimize the line width and flow compensation parameters.",
"the four bottom layers do not touch, so the print is not watertight.",
"an open cube with 4 bottom layers). The wall width I measured on",
"better than before. There is only one problem: the parallel lines in the",
"repeated the print. The wall width I got from this was 0.45 mm,",
"mm, which is much better than before. There is only one problem: the",
"a 0.4 mm nozzle and therefore set the line width parameter to 0.4",
"To correct for the difference I set the flow compensation to 80% and",
"not watertight. Up to now I assumed that Cura would calculate the distance",
"i3 clone. I'm using Cura 3.1 for slicing. After calibrating the extruder steps,",
"to 0.4 mm there should even be some overlap. Why am I seeing",
"do not touch, so the print is not watertight. Up to now I",
"then printed a cube with 0% infill, 1 wall line and no top",
"infill, 1 wall line and no top layers (basically an open cube with",
"line and no top layers (basically an open cube with 4 bottom layers).",
"from this was 0.45 mm, which is much better than before. There is",
"to now I assumed that Cura would calculate the distance between the lines",
"cube with 4 bottom layers). The wall width I measured on the printed",
"parallel lines in the four bottom layers do not touch, so the print",
"therefore set the line width parameter to 0.4 mm in Cura. I then",
"should even be some overlap. Why am I seeing this effect? Am I",
"difference I set the flow compensation to 80% and repeated the print. The",
"layers do not touch, so the print is not watertight. Up to now",
"to 80% and repeated the print. The wall width I got from this",
"mm. To correct for the difference I set the flow compensation to 80%",
"parameters. I am using a 0.4 mm nozzle and therefore set the line",
"printed result is 0.52 mm. To correct for the difference I set the",
"and repeated the print. The wall width I got from this was 0.45",
"flow compensation to 80% and repeated the print. The wall width I got",
"with 0.45 mm lines and line width set to 0.4 mm there should",
"is 0.52 mm. To correct for the difference I set the flow compensation",
"lines from the line width setting. So with 0.45 mm lines and line",
"open cube with 4 bottom layers). The wall width I measured on the",
"0.45 mm lines and line width set to 0.4 mm there should even",
"wall width I got from this was 0.45 mm, which is much better",
"width I measured on the printed result is 0.52 mm. To correct for",
"there should even be some overlap. Why am I seeing this effect? Am",
"in the four bottom layers do not touch, so the print is not",
"steps, I wanted to optimize the line width and flow compensation parameters. I",
"I'm using Cura 3.1 for slicing. After calibrating the extruder steps, I wanted",
"0.52 mm. To correct for the difference I set the flow compensation to",
"with 4 bottom layers). The wall width I measured on the printed result",
"to 0.4 mm in Cura. I then printed a cube with 0% infill,",
"this was 0.45 mm, which is much better than before. There is only",
"a cube with 0% infill, 1 wall line and no top layers (basically",
"Why am I seeing this effect? Am I getting something fundamentally wrong here?",
"be some overlap. Why am I seeing this effect? Am I getting something",
"overlap. Why am I seeing this effect? Am I getting something fundamentally wrong",
"cube with 0% infill, 1 wall line and no top layers (basically an",
"the printed result is 0.52 mm. To correct for the difference I set",
"setting. So with 0.45 mm lines and line width set to 0.4 mm",
"the distance between the lines from the line width setting. So with 0.45",
"0.4 mm nozzle and therefore set the line width parameter to 0.4 mm",
"that Cura would calculate the distance between the lines from the line width",
"set the flow compensation to 80% and repeated the print. The wall width",
"and no top layers (basically an open cube with 4 bottom layers). The",
"my cheap CTC i3 clone. I'm using Cura 3.1 for slicing. After calibrating",
"and therefore set the line width parameter to 0.4 mm in Cura. I",
"width parameter to 0.4 mm in Cura. I then printed a cube with",
"I wanted to optimize the line width and flow compensation parameters. I am",
"was 0.45 mm, which is much better than before. There is only one",
"clone. I'm using Cura 3.1 for slicing. After calibrating the extruder steps, I",
"than before. There is only one problem: the parallel lines in the four",
"lines in the four bottom layers do not touch, so the print is",
"I'm currently in the process of fine-tuning my cheap CTC i3 clone. I'm",
"0% infill, 1 wall line and no top layers (basically an open cube",
"0.45 mm, which is much better than before. There is only one problem:",
"problem: the parallel lines in the four bottom layers do not touch, so",
"print is not watertight. Up to now I assumed that Cura would calculate",
"now I assumed that Cura would calculate the distance between the lines from",
"calibrating the extruder steps, I wanted to optimize the line width and flow",
"set to 0.4 mm there should even be some overlap. Why am I",
"assumed that Cura would calculate the distance between the lines from the line",
"mm in Cura. I then printed a cube with 0% infill, 1 wall",
"layers (basically an open cube with 4 bottom layers). The wall width I",
"even be some overlap. Why am I seeing this effect? Am I getting",
"Cura 3.1 for slicing. After calibrating the extruder steps, I wanted to optimize",
"width and flow compensation parameters. I am using a 0.4 mm nozzle and",
"width setting. So with 0.45 mm lines and line width set to 0.4",
"from the line width setting. So with 0.45 mm lines and line width",
"watertight. Up to now I assumed that Cura would calculate the distance between",
"is much better than before. There is only one problem: the parallel lines",
"line width setting. So with 0.45 mm lines and line width set to",
"only one problem: the parallel lines in the four bottom layers do not",
"compensation to 80% and repeated the print. The wall width I got from",
"There is only one problem: the parallel lines in the four bottom layers",
"is not watertight. Up to now I assumed that Cura would calculate the",
"got from this was 0.45 mm, which is much better than before. There",
"Cura. I then printed a cube with 0% infill, 1 wall line and",
"result is 0.52 mm. To correct for the difference I set the flow",
"mm nozzle and therefore set the line width parameter to 0.4 mm in",
"no top layers (basically an open cube with 4 bottom layers). The wall",
"the flow compensation to 80% and repeated the print. The wall width I",
"fine-tuning my cheap CTC i3 clone. I'm using Cura 3.1 for slicing. After",
"optimize the line width and flow compensation parameters. I am using a 0.4",
"CTC i3 clone. I'm using Cura 3.1 for slicing. After calibrating the extruder",
"I measured on the printed result is 0.52 mm. To correct for the",
"After calibrating the extruder steps, I wanted to optimize the line width and",
"between the lines from the line width setting. So with 0.45 mm lines",
"printed a cube with 0% infill, 1 wall line and no top layers",
"line width parameter to 0.4 mm in Cura. I then printed a cube",
"So with 0.45 mm lines and line width set to 0.4 mm there",
"so the print is not watertight. Up to now I assumed that Cura",
"slicing. After calibrating the extruder steps, I wanted to optimize the line width",
"1 wall line and no top layers (basically an open cube with 4",
"for the difference I set the flow compensation to 80% and repeated the",
"0.4 mm in Cura. I then printed a cube with 0% infill, 1",
"mm there should even be some overlap. Why am I seeing this effect?",
"for slicing. After calibrating the extruder steps, I wanted to optimize the line",
"bottom layers do not touch, so the print is not watertight. Up to",
"parameter to 0.4 mm in Cura. I then printed a cube with 0%",
"the difference I set the flow compensation to 80% and repeated the print.",
"using a 0.4 mm nozzle and therefore set the line width parameter to",
"to optimize the line width and flow compensation parameters. I am using a",
"the lines from the line width setting. So with 0.45 mm lines and",
"currently in the process of fine-tuning my cheap CTC i3 clone. I'm using",
"much better than before. There is only one problem: the parallel lines in",
"the line width setting. So with 0.45 mm lines and line width set",
"the line width parameter to 0.4 mm in Cura. I then printed a",
"measured on the printed result is 0.52 mm. To correct for the difference",
"Cura would calculate the distance between the lines from the line width setting.",
"am using a 0.4 mm nozzle and therefore set the line width parameter",
"four bottom layers do not touch, so the print is not watertight. Up",
"and line width set to 0.4 mm there should even be some overlap.",
"the line width and flow compensation parameters. I am using a 0.4 mm",
"top layers (basically an open cube with 4 bottom layers). The wall width",
"layers). The wall width I measured on the printed result is 0.52 mm.",
"I am using a 0.4 mm nozzle and therefore set the line width",
"one problem: the parallel lines in the four bottom layers do not touch,",
"0.4 mm there should even be some overlap. Why am I seeing this",
"line width set to 0.4 mm there should even be some overlap. Why",
"nozzle and therefore set the line width parameter to 0.4 mm in Cura.",
"in the process of fine-tuning my cheap CTC i3 clone. I'm using Cura",
"80% and repeated the print. The wall width I got from this was",
"compensation parameters. I am using a 0.4 mm nozzle and therefore set the",
"I then printed a cube with 0% infill, 1 wall line and no",
"would calculate the distance between the lines from the line width setting. So",
"distance between the lines from the line width setting. So with 0.45 mm",
"with 0% infill, 1 wall line and no top layers (basically an open",
"which is much better than before. There is only one problem: the parallel",
"wanted to optimize the line width and flow compensation parameters. I am using",
"some overlap. Why am I seeing this effect? Am I getting something fundamentally",
"calculate the distance between the lines from the line width setting. So with",
"using Cura 3.1 for slicing. After calibrating the extruder steps, I wanted to",
"on the printed result is 0.52 mm. To correct for the difference I",
"lines and line width set to 0.4 mm there should even be some",
"The wall width I measured on the printed result is 0.52 mm. To",
"the extruder steps, I wanted to optimize the line width and flow compensation",
"I assumed that Cura would calculate the distance between the lines from the",
"4 bottom layers). The wall width I measured on the printed result is",
"3.1 for slicing. After calibrating the extruder steps, I wanted to optimize the",
"is only one problem: the parallel lines in the four bottom layers do",
"and flow compensation parameters. I am using a 0.4 mm nozzle and therefore",
"mm lines and line width set to 0.4 mm there should even be",
"width set to 0.4 mm there should even be some overlap. Why am",
"the process of fine-tuning my cheap CTC i3 clone. I'm using Cura 3.1",
"print. The wall width I got from this was 0.45 mm, which is",
"the parallel lines in the four bottom layers do not touch, so the",
"the print. The wall width I got from this was 0.45 mm, which",
"line width and flow compensation parameters. I am using a 0.4 mm nozzle",
"process of fine-tuning my cheap CTC i3 clone. I'm using Cura 3.1 for",
"touch, so the print is not watertight. Up to now I assumed that",
"correct for the difference I set the flow compensation to 80% and repeated",
"wall line and no top layers (basically an open cube with 4 bottom",
"bottom layers). The wall width I measured on the printed result is 0.52",
"I set the flow compensation to 80% and repeated the print. The wall",
"set the line width parameter to 0.4 mm in Cura. I then printed"
] |
[
"home position and the PINDA probe is too far out over the heatbed",
"losing any printing area and hopefully prevents me having to edit any code.",
"be to move extruder 17mm closer to be the same as the original",
"be the same as the original printer but my deadline is fast approaching",
"a new extruder to attach to a Prusa i3 MK2. My problem is",
"0.5mm to the right. As a result when I try and calibrate the",
"planning on removing the heatbed and placing spacers that will move the printing",
"Prusa i3 MK2. My problem is that both the nozzle and PINDA probe",
"when I try and calibrate the printer it moves to the home position",
"and calibrate the printer it moves to the home position and the PINDA",
"to be the same as the original printer but my deadline is fast",
"surface 17mm forward. This should then prevent the printer losing any printing area",
"to attach to a Prusa i3 MK2. My problem is that both the",
"out over the heatbed so it doesn't detect the printing surface. What is",
"calibrate the printer it moves to the home position and the PINDA probe",
"do would be to move extruder 17mm closer to be the same as",
"position so that the printer can be properly calibrated? UPDATE: I am planning",
"prevent the printer losing any printing area and hopefully prevents me having to",
"edit any code. Can anyone see any problems with this I'm overlooking? The",
"to do would be to move extruder 17mm closer to be the same",
"would be to move extruder 17mm closer to be the same as the",
"with this I'm overlooking? The simplest thing to do would be to move",
"part of a project with my university, I have developed a new extruder",
"the printer it moves to the home position and the PINDA probe is",
"university, I have developed a new extruder to attach to a Prusa i3",
"thing to do would be to move extruder 17mm closer to be the",
"result when I try and calibrate the printer it moves to the home",
"any printing area and hopefully prevents me having to edit any code. Can",
"probe is too far out over the heatbed so it doesn't detect the",
"the heatbed and placing spacers that will move the printing surface 17mm forward.",
"17mm closer to be the same as the original printer but my deadline",
"both the nozzle and PINDA probe have moved 17mm forward and 0.5mm to",
"is that both the nozzle and PINDA probe have moved 17mm forward and",
"a Prusa i3 MK2. My problem is that both the nozzle and PINDA",
"the PINDA probe is too far out over the heatbed so it doesn't",
"right. As a result when I try and calibrate the printer it moves",
"home position so that the printer can be properly calibrated? UPDATE: I am",
"the same as the original printer but my deadline is fast approaching and",
"heatbed and placing spacers that will move the printing surface 17mm forward. This",
"this I'm overlooking? The simplest thing to do would be to move extruder",
"printer but my deadline is fast approaching and I haven't time for a",
"What is the simplest method of moving the home position so that the",
"printer losing any printing area and hopefully prevents me having to edit any",
"position and the PINDA probe is too far out over the heatbed so",
"calibrated? UPDATE: I am planning on removing the heatbed and placing spacers that",
"any code. Can anyone see any problems with this I'm overlooking? The simplest",
"try and calibrate the printer it moves to the home position and the",
"prevents me having to edit any code. Can anyone see any problems with",
"As part of a project with my university, I have developed a new",
"move extruder 17mm closer to be the same as the original printer but",
"the home position so that the printer can be properly calibrated? UPDATE: I",
"of a project with my university, I have developed a new extruder to",
"should then prevent the printer losing any printing area and hopefully prevents me",
"is too far out over the heatbed so it doesn't detect the printing",
"is the simplest method of moving the home position so that the printer",
"with my university, I have developed a new extruder to attach to a",
"and the PINDA probe is too far out over the heatbed so it",
"as the original printer but my deadline is fast approaching and I haven't",
"spacers that will move the printing surface 17mm forward. This should then prevent",
"I am planning on removing the heatbed and placing spacers that will move",
"my university, I have developed a new extruder to attach to a Prusa",
"This should then prevent the printer losing any printing area and hopefully prevents",
"overlooking? The simplest thing to do would be to move extruder 17mm closer",
"MK2. My problem is that both the nozzle and PINDA probe have moved",
"and 0.5mm to the right. As a result when I try and calibrate",
"the heatbed so it doesn't detect the printing surface. What is the simplest",
"and placing spacers that will move the printing surface 17mm forward. This should",
"properly calibrated? UPDATE: I am planning on removing the heatbed and placing spacers",
"it doesn't detect the printing surface. What is the simplest method of moving",
"closer to be the same as the original printer but my deadline is",
"move the printing surface 17mm forward. This should then prevent the printer losing",
"problem is that both the nozzle and PINDA probe have moved 17mm forward",
"far out over the heatbed so it doesn't detect the printing surface. What",
"hopefully prevents me having to edit any code. Can anyone see any problems",
"I try and calibrate the printer it moves to the home position and",
"My problem is that both the nozzle and PINDA probe have moved 17mm",
"surface. What is the simplest method of moving the home position so that",
"PINDA probe is too far out over the heatbed so it doesn't detect",
"UPDATE: I am planning on removing the heatbed and placing spacers that will",
"As a result when I try and calibrate the printer it moves to",
"the printing surface 17mm forward. This should then prevent the printer losing any",
"the printing surface. What is the simplest method of moving the home position",
"having to edit any code. Can anyone see any problems with this I'm",
"a result when I try and calibrate the printer it moves to the",
"area and hopefully prevents me having to edit any code. Can anyone see",
"printing area and hopefully prevents me having to edit any code. Can anyone",
"printer can be properly calibrated? UPDATE: I am planning on removing the heatbed",
"code. Can anyone see any problems with this I'm overlooking? The simplest thing",
"a project with my university, I have developed a new extruder to attach",
"new extruder to attach to a Prusa i3 MK2. My problem is that",
"the right. As a result when I try and calibrate the printer it",
"17mm forward and 0.5mm to the right. As a result when I try",
"me having to edit any code. Can anyone see any problems with this",
"simplest thing to do would be to move extruder 17mm closer to be",
"on removing the heatbed and placing spacers that will move the printing surface",
"the original printer but my deadline is fast approaching and I haven't time",
"moved 17mm forward and 0.5mm to the right. As a result when I",
"placing spacers that will move the printing surface 17mm forward. This should then",
"attach to a Prusa i3 MK2. My problem is that both the nozzle",
"moves to the home position and the PINDA probe is too far out",
"so it doesn't detect the printing surface. What is the simplest method of",
"be properly calibrated? UPDATE: I am planning on removing the heatbed and placing",
"will move the printing surface 17mm forward. This should then prevent the printer",
"printing surface 17mm forward. This should then prevent the printer losing any printing",
"developed a new extruder to attach to a Prusa i3 MK2. My problem",
"moving the home position so that the printer can be properly calibrated? UPDATE:",
"and hopefully prevents me having to edit any code. Can anyone see any",
"it moves to the home position and the PINDA probe is too far",
"to a Prusa i3 MK2. My problem is that both the nozzle and",
"that both the nozzle and PINDA probe have moved 17mm forward and 0.5mm",
"detect the printing surface. What is the simplest method of moving the home",
"forward and 0.5mm to the right. As a result when I try and",
"forward. This should then prevent the printer losing any printing area and hopefully",
"deadline is fast approaching and I haven't time for a redesign that large.",
"any problems with this I'm overlooking? The simplest thing to do would be",
"17mm forward. This should then prevent the printer losing any printing area and",
"the simplest method of moving the home position so that the printer can",
"the printer can be properly calibrated? UPDATE: I am planning on removing the",
"over the heatbed so it doesn't detect the printing surface. What is the",
"too far out over the heatbed so it doesn't detect the printing surface.",
"The simplest thing to do would be to move extruder 17mm closer to",
"to move extruder 17mm closer to be the same as the original printer",
"am planning on removing the heatbed and placing spacers that will move the",
"the nozzle and PINDA probe have moved 17mm forward and 0.5mm to the",
"that the printer can be properly calibrated? UPDATE: I am planning on removing",
"heatbed so it doesn't detect the printing surface. What is the simplest method",
"removing the heatbed and placing spacers that will move the printing surface 17mm",
"can be properly calibrated? UPDATE: I am planning on removing the heatbed and",
"probe have moved 17mm forward and 0.5mm to the right. As a result",
"I have developed a new extruder to attach to a Prusa i3 MK2.",
"to edit any code. Can anyone see any problems with this I'm overlooking?",
"Can anyone see any problems with this I'm overlooking? The simplest thing to",
"PINDA probe have moved 17mm forward and 0.5mm to the right. As a",
"the printer losing any printing area and hopefully prevents me having to edit",
"doesn't detect the printing surface. What is the simplest method of moving the",
"to the right. As a result when I try and calibrate the printer",
"see any problems with this I'm overlooking? The simplest thing to do would",
"simplest method of moving the home position so that the printer can be",
"then prevent the printer losing any printing area and hopefully prevents me having",
"printer it moves to the home position and the PINDA probe is too",
"extruder 17mm closer to be the same as the original printer but my",
"the home position and the PINDA probe is too far out over the",
"my deadline is fast approaching and I haven't time for a redesign that",
"extruder to attach to a Prusa i3 MK2. My problem is that both",
"to the home position and the PINDA probe is too far out over",
"I'm overlooking? The simplest thing to do would be to move extruder 17mm",
"method of moving the home position so that the printer can be properly",
"same as the original printer but my deadline is fast approaching and I",
"that will move the printing surface 17mm forward. This should then prevent the",
"printing surface. What is the simplest method of moving the home position so",
"project with my university, I have developed a new extruder to attach to",
"so that the printer can be properly calibrated? UPDATE: I am planning on",
"and PINDA probe have moved 17mm forward and 0.5mm to the right. As",
"anyone see any problems with this I'm overlooking? The simplest thing to do",
"of moving the home position so that the printer can be properly calibrated?",
"i3 MK2. My problem is that both the nozzle and PINDA probe have",
"nozzle and PINDA probe have moved 17mm forward and 0.5mm to the right.",
"have moved 17mm forward and 0.5mm to the right. As a result when",
"problems with this I'm overlooking? The simplest thing to do would be to",
"original printer but my deadline is fast approaching and I haven't time for",
"have developed a new extruder to attach to a Prusa i3 MK2. My",
"but my deadline is fast approaching and I haven't time for a redesign"
] |
[
"this is the end script: ``` G92 E0 G1 E-1.5000 F1800 ; layer",
"Build Summary ; Build time: 3 hours 9 minutes ; Filament length: 12689.1",
"to the border of the shape. I supposed that some scripts has changed",
"printed part and I noticed due the part is 14x8 and the nozzle",
"``` Z axis moves down 4mm after finishing going to X0, why? I",
"; Build Summary ; Build time: 3 hours 9 minutes ; Filament length:",
"m) ; Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15 g",
"printing has finishig and causes the nozzle crashes to the printed part and",
"the printing has finishig and causes the nozzle crashes to the printed part",
"the end script: ``` G92 E0 G1 E-1.5000 F1800 ; layer end M104",
"has finishig and causes the nozzle crashes to the printed part and I",
"scripts has changed but, seems to be everything ok. this is the end",
"; layer end M104 S0 ; turn off extruder M140 S0 ; turn",
"cc) ; Plastic weight: 38.15 g (0.08 lb) ``` Z axis moves down",
"time that I saw this movement after the printing has finishig and causes",
"noticed due the part is 14x8 and the nozzle is to near and",
"turn off bed G28 X0 ; home X axis M84 ; disable motors",
"nozzle is to near and below to the border of the shape. I",
"ok. this is the end script: ``` G92 E0 G1 E-1.5000 F1800 ;",
"extruder M140 S0 ; turn off bed G28 X0 ; home X axis",
"30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15 g (0.08 lb) ``` Z",
"14x8 and the nozzle is to near and below to the border of",
"that I saw this movement after the printing has finishig and causes the",
"is 14x8 and the nozzle is to near and below to the border",
"12689.1 mm (12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic",
"end M104 S0 ; turn off extruder M140 S0 ; turn off bed",
"is the end script: ``` G92 E0 G1 E-1.5000 F1800 ; layer end",
"layer end M104 S0 ; turn off extruder M140 S0 ; turn off",
"the shape. I supposed that some scripts has changed but, seems to be",
"hours 9 minutes ; Filament length: 12689.1 mm (12.69 m) ; Plastic volume:",
"I noticed due the part is 14x8 and the nozzle is to near",
"weight: 38.15 g (0.08 lb) ``` Z axis moves down 4mm after finishing",
"shape. I supposed that some scripts has changed but, seems to be everything",
"38.15 g (0.08 lb) ``` Z axis moves down 4mm after finishing going",
"the border of the shape. I supposed that some scripts has changed but,",
"is to near and below to the border of the shape. I supposed",
"; Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15 g (0.08",
"4mm after finishing going to X0, why? I don't want the nozzle crashes",
"that some scripts has changed but, seems to be everything ok. this is",
"G28 X0 ; home X axis M84 ; disable motors ; Build Summary",
"motors ; Build Summary ; Build time: 3 hours 9 minutes ; Filament",
"volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15 g (0.08 lb) ```",
"end script: ``` G92 E0 G1 E-1.5000 F1800 ; layer end M104 S0",
"but, seems to be everything ok. this is the end script: ``` G92",
"off extruder M140 S0 ; turn off bed G28 X0 ; home X",
"X0, why? I don't want the nozzle crashes the part on going to",
"F1800 ; layer end M104 S0 ; turn off extruder M140 S0 ;",
"the nozzle crashes to the printed part and I noticed due the part",
"axis moves down 4mm after finishing going to X0, why? I don't want",
"finishig and causes the nozzle crashes to the printed part and I noticed",
"G92 E0 G1 E-1.5000 F1800 ; layer end M104 S0 ; turn off",
"moves down 4mm after finishing going to X0, why? I don't want the",
"to the printed part and I noticed due the part is 14x8 and",
"near and below to the border of the shape. I supposed that some",
"length: 12689.1 mm (12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52 cc) ;",
"E-1.5000 F1800 ; layer end M104 S0 ; turn off extruder M140 S0",
"(12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15",
"the firts time that I saw this movement after the printing has finishig",
"E0 G1 E-1.5000 F1800 ; layer end M104 S0 ; turn off extruder",
"G1 E-1.5000 F1800 ; layer end M104 S0 ; turn off extruder M140",
"some scripts has changed but, seems to be everything ok. this is the",
"; turn off extruder M140 S0 ; turn off bed G28 X0 ;",
"X0 ; home X axis M84 ; disable motors ; Build Summary ;",
"off bed G28 X0 ; home X axis M84 ; disable motors ;",
"S0 ; turn off extruder M140 S0 ; turn off bed G28 X0",
"Plastic weight: 38.15 g (0.08 lb) ``` Z axis moves down 4mm after",
"this movement after the printing has finishig and causes the nozzle crashes to",
"of the shape. I supposed that some scripts has changed but, seems to",
"border of the shape. I supposed that some scripts has changed but, seems",
"Build time: 3 hours 9 minutes ; Filament length: 12689.1 mm (12.69 m)",
"due the part is 14x8 and the nozzle is to near and below",
"to X0, why? I don't want the nozzle crashes the part on going",
"``` G92 E0 G1 E-1.5000 F1800 ; layer end M104 S0 ; turn",
"the nozzle is to near and below to the border of the shape.",
"and below to the border of the shape. I supposed that some scripts",
"to near and below to the border of the shape. I supposed that",
"seems to be everything ok. this is the end script: ``` G92 E0",
"firts time that I saw this movement after the printing has finishig and",
"; home X axis M84 ; disable motors ; Build Summary ; Build",
"axis M84 ; disable motors ; Build Summary ; Build time: 3 hours",
"Is the firts time that I saw this movement after the printing has",
"be everything ok. this is the end script: ``` G92 E0 G1 E-1.5000",
"causes the nozzle crashes to the printed part and I noticed due the",
"lb) ``` Z axis moves down 4mm after finishing going to X0, why?",
"I supposed that some scripts has changed but, seems to be everything ok.",
"script: ``` G92 E0 G1 E-1.5000 F1800 ; layer end M104 S0 ;",
"(0.08 lb) ``` Z axis moves down 4mm after finishing going to X0,",
"; Filament length: 12689.1 mm (12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52",
"M104 S0 ; turn off extruder M140 S0 ; turn off bed G28",
"to be everything ok. this is the end script: ``` G92 E0 G1",
"changed but, seems to be everything ok. this is the end script: ```",
"supposed that some scripts has changed but, seems to be everything ok. this",
"; disable motors ; Build Summary ; Build time: 3 hours 9 minutes",
"crashes to the printed part and I noticed due the part is 14x8",
"Z axis moves down 4mm after finishing going to X0, why? I don't",
"finishing going to X0, why? I don't want the nozzle crashes the part",
"has changed but, seems to be everything ok. this is the end script:",
"M140 S0 ; turn off bed G28 X0 ; home X axis M84",
"time: 3 hours 9 minutes ; Filament length: 12689.1 mm (12.69 m) ;",
"minutes ; Filament length: 12689.1 mm (12.69 m) ; Plastic volume: 30520.78 mm^3",
"I saw this movement after the printing has finishig and causes the nozzle",
"M84 ; disable motors ; Build Summary ; Build time: 3 hours 9",
"; Build time: 3 hours 9 minutes ; Filament length: 12689.1 mm (12.69",
"; turn off bed G28 X0 ; home X axis M84 ; disable",
"(30.52 cc) ; Plastic weight: 38.15 g (0.08 lb) ``` Z axis moves",
"nozzle crashes to the printed part and I noticed due the part is",
"part and I noticed due the part is 14x8 and the nozzle is",
"and I noticed due the part is 14x8 and the nozzle is to",
"home X axis M84 ; disable motors ; Build Summary ; Build time:",
"mm^3 (30.52 cc) ; Plastic weight: 38.15 g (0.08 lb) ``` Z axis",
"disable motors ; Build Summary ; Build time: 3 hours 9 minutes ;",
"going to X0, why? I don't want the nozzle crashes the part on",
"after the printing has finishig and causes the nozzle crashes to the printed",
"Filament length: 12689.1 mm (12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52 cc)",
"saw this movement after the printing has finishig and causes the nozzle crashes",
"why? I don't want the nozzle crashes the part on going to zero.",
"and causes the nozzle crashes to the printed part and I noticed due",
"X axis M84 ; disable motors ; Build Summary ; Build time: 3",
"after finishing going to X0, why? I don't want the nozzle crashes the",
"g (0.08 lb) ``` Z axis moves down 4mm after finishing going to",
"; Plastic weight: 38.15 g (0.08 lb) ``` Z axis moves down 4mm",
"mm (12.69 m) ; Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight:",
"below to the border of the shape. I supposed that some scripts has",
"S0 ; turn off bed G28 X0 ; home X axis M84 ;",
"Summary ; Build time: 3 hours 9 minutes ; Filament length: 12689.1 mm",
"and the nozzle is to near and below to the border of the",
"3 hours 9 minutes ; Filament length: 12689.1 mm (12.69 m) ; Plastic",
"everything ok. this is the end script: ``` G92 E0 G1 E-1.5000 F1800",
"down 4mm after finishing going to X0, why? I don't want the nozzle",
"movement after the printing has finishig and causes the nozzle crashes to the",
"Plastic volume: 30520.78 mm^3 (30.52 cc) ; Plastic weight: 38.15 g (0.08 lb)",
"the part is 14x8 and the nozzle is to near and below to",
"9 minutes ; Filament length: 12689.1 mm (12.69 m) ; Plastic volume: 30520.78",
"part is 14x8 and the nozzle is to near and below to the",
"turn off extruder M140 S0 ; turn off bed G28 X0 ; home",
"bed G28 X0 ; home X axis M84 ; disable motors ; Build",
"the printed part and I noticed due the part is 14x8 and the"
] |
[
"Is there an integrated kickback protection in stepper motor drivers or should I",
"the steppers might fry the driver or the arduino when i turn off",
"the power supply. I haven't had an issue yet but it still bothers",
"I am afraid the steppers might fry the driver or the arduino when",
"when i turn off the power for them. I do that by turning",
"protection in stepper motor drivers or should I make my own? I am",
"drivers or should I make my own? I am afraid the steppers might",
"an integrated kickback protection in stepper motor drivers or should I make my",
"power for them. I do that by turning off the power supply. I",
"I make my own? I am afraid the steppers might fry the driver",
"do that by turning off the power supply. I haven't had an issue",
"or should I make my own? I am afraid the steppers might fry",
"integrated kickback protection in stepper motor drivers or should I make my own?",
"the arduino when i turn off the power for them. I do that",
"make my own? I am afraid the steppers might fry the driver or",
"arduino when i turn off the power for them. I do that by",
"turning off the power supply. I haven't had an issue yet but it",
"them. I do that by turning off the power supply. I haven't had",
"should I make my own? I am afraid the steppers might fry the",
"my own? I am afraid the steppers might fry the driver or the",
"driver or the arduino when i turn off the power for them. I",
"afraid the steppers might fry the driver or the arduino when i turn",
"i turn off the power for them. I do that by turning off",
"motor drivers or should I make my own? I am afraid the steppers",
"by turning off the power supply. I haven't had an issue yet but",
"off the power supply. I haven't had an issue yet but it still",
"steppers might fry the driver or the arduino when i turn off the",
"I do that by turning off the power supply. I haven't had an",
"power supply. I haven't had an issue yet but it still bothers me.",
"stepper motor drivers or should I make my own? I am afraid the",
"or the arduino when i turn off the power for them. I do",
"in stepper motor drivers or should I make my own? I am afraid",
"for them. I do that by turning off the power supply. I haven't",
"that by turning off the power supply. I haven't had an issue yet",
"am afraid the steppers might fry the driver or the arduino when i",
"might fry the driver or the arduino when i turn off the power",
"fry the driver or the arduino when i turn off the power for",
"off the power for them. I do that by turning off the power",
"kickback protection in stepper motor drivers or should I make my own? I",
"there an integrated kickback protection in stepper motor drivers or should I make",
"the power for them. I do that by turning off the power supply.",
"turn off the power for them. I do that by turning off the",
"the driver or the arduino when i turn off the power for them.",
"own? I am afraid the steppers might fry the driver or the arduino"
] |
[
"first 3D printer today, QIDI X-ONE[2], and so far so good with the",
"my 1st print. I wanted to power off the printer, but I don't",
"today, QIDI X-ONE[2], and so far so good with the setup and getting",
"X-ONE[2], and so far so good with the setup and getting my 1st",
"don't see any instructions on how to properly power off the machine. Does",
"to power off the printer, but I don't see any instructions on how",
"so far so good with the setup and getting my 1st print. I",
"how long I should wait, or what the minimum temperature would be safe",
"to properly power off the machine. Does anyone know how long I should",
"and so far so good with the setup and getting my 1st print.",
"print. I wanted to power off the printer, but I don't see any",
"machine. Does anyone know how long I should wait, or what the minimum",
"see any instructions on how to properly power off the machine. Does anyone",
"off the machine. Does anyone know how long I should wait, or what",
"with the setup and getting my 1st print. I wanted to power off",
"so good with the setup and getting my 1st print. I wanted to",
"my first 3D printer today, QIDI X-ONE[2], and so far so good with",
"power off the printer, but I don't see any instructions on how to",
"I just got my first 3D printer today, QIDI X-ONE[2], and so far",
"power off the machine. Does anyone know how long I should wait, or",
"but I don't see any instructions on how to properly power off the",
"Does anyone know how long I should wait, or what the minimum temperature",
"good with the setup and getting my 1st print. I wanted to power",
"wanted to power off the printer, but I don't see any instructions on",
"setup and getting my 1st print. I wanted to power off the printer,",
"printer today, QIDI X-ONE[2], and so far so good with the setup and",
"QIDI X-ONE[2], and so far so good with the setup and getting my",
"I don't see any instructions on how to properly power off the machine.",
"on how to properly power off the machine. Does anyone know how long",
"printer, but I don't see any instructions on how to properly power off",
"instructions on how to properly power off the machine. Does anyone know how",
"far so good with the setup and getting my 1st print. I wanted",
"the setup and getting my 1st print. I wanted to power off the",
"any instructions on how to properly power off the machine. Does anyone know",
"I wanted to power off the printer, but I don't see any instructions",
"long I should wait, or what the minimum temperature would be safe to",
"properly power off the machine. Does anyone know how long I should wait,",
"anyone know how long I should wait, or what the minimum temperature would",
"or what the minimum temperature would be safe to power down the machine?",
"getting my 1st print. I wanted to power off the printer, but I",
"the printer, but I don't see any instructions on how to properly power",
"off the printer, but I don't see any instructions on how to properly",
"should wait, or what the minimum temperature would be safe to power down",
"got my first 3D printer today, QIDI X-ONE[2], and so far so good",
"3D printer today, QIDI X-ONE[2], and so far so good with the setup",
"and getting my 1st print. I wanted to power off the printer, but",
"I should wait, or what the minimum temperature would be safe to power",
"1st print. I wanted to power off the printer, but I don't see",
"know how long I should wait, or what the minimum temperature would be",
"wait, or what the minimum temperature would be safe to power down the",
"the machine. Does anyone know how long I should wait, or what the",
"just got my first 3D printer today, QIDI X-ONE[2], and so far so",
"how to properly power off the machine. Does anyone know how long I"
] |
[
"I want to verify that it is possible to use a battery to",
"the power consumption of your heatbed (size) and hotend (model)? I want to",
"What is the power consumption of your heatbed (size) and hotend (model)? I",
"want to verify that it is possible to use a battery to power",
"and hotend (model)? I want to verify that it is possible to use",
"to verify that it is possible to use a battery to power them.",
"power consumption of your heatbed (size) and hotend (model)? I want to verify",
"(model)? I want to verify that it is possible to use a battery",
"(size) and hotend (model)? I want to verify that it is possible to",
"your heatbed (size) and hotend (model)? I want to verify that it is",
"of your heatbed (size) and hotend (model)? I want to verify that it",
"is the power consumption of your heatbed (size) and hotend (model)? I want",
"heatbed (size) and hotend (model)? I want to verify that it is possible",
"consumption of your heatbed (size) and hotend (model)? I want to verify that",
"hotend (model)? I want to verify that it is possible to use a"
] |
[
"The resistance of the heat block will be used. The current to this",
"a circuit. The voltage will be set with pwm. Is this possible with",
"small heat block to increase/decrease the heat as fast as possible. The resistance",
"used. The current to this block is 500mA and is set constant with",
"a very small heat block to increase/decrease the heat as fast as possible.",
"of the heat block will be used. The current to this block is",
"block is 500mA and is set constant with a circuit. The voltage will",
"heater? My idea is to build a very small heat block to increase/decrease",
"heat as fast as possible. The resistance of the heat block will be",
"current to this block is 500mA and is set constant with a circuit.",
"it possible to design a heat block without cartridge heater? My idea is",
"cartridge heater? My idea is to build a very small heat block to",
"build a very small heat block to increase/decrease the heat as fast as",
"the heat as fast as possible. The resistance of the heat block will",
"fast as possible. The resistance of the heat block will be used. The",
"and is set constant with a circuit. The voltage will be set with",
"Is it possible to design a heat block without cartridge heater? My idea",
"heat block will be used. The current to this block is 500mA and",
"possible to design a heat block without cartridge heater? My idea is to",
"this block is 500mA and is set constant with a circuit. The voltage",
"resistance of the heat block will be used. The current to this block",
"is to build a very small heat block to increase/decrease the heat as",
"possible. The resistance of the heat block will be used. The current to",
"heat block to increase/decrease the heat as fast as possible. The resistance of",
"to build a very small heat block to increase/decrease the heat as fast",
"be used. The current to this block is 500mA and is set constant",
"is set constant with a circuit. The voltage will be set with pwm.",
"will be used. The current to this block is 500mA and is set",
"constant with a circuit. The voltage will be set with pwm. Is this",
"to increase/decrease the heat as fast as possible. The resistance of the heat",
"as fast as possible. The resistance of the heat block will be used.",
"to this block is 500mA and is set constant with a circuit. The",
"a heat block without cartridge heater? My idea is to build a very",
"to design a heat block without cartridge heater? My idea is to build",
"very small heat block to increase/decrease the heat as fast as possible. The",
"500mA and is set constant with a circuit. The voltage will be set",
"set constant with a circuit. The voltage will be set with pwm. Is",
"the heat block will be used. The current to this block is 500mA",
"voltage will be set with pwm. Is this possible with 500mA and 5V",
"will be set with pwm. Is this possible with 500mA and 5V (2,5W)?",
"as possible. The resistance of the heat block will be used. The current",
"The current to this block is 500mA and is set constant with a",
"heat block without cartridge heater? My idea is to build a very small",
"increase/decrease the heat as fast as possible. The resistance of the heat block",
"My idea is to build a very small heat block to increase/decrease the",
"block will be used. The current to this block is 500mA and is",
"idea is to build a very small heat block to increase/decrease the heat",
"block to increase/decrease the heat as fast as possible. The resistance of the",
"circuit. The voltage will be set with pwm. Is this possible with 500mA",
"block without cartridge heater? My idea is to build a very small heat",
"without cartridge heater? My idea is to build a very small heat block",
"with a circuit. The voltage will be set with pwm. Is this possible",
"The voltage will be set with pwm. Is this possible with 500mA and",
"is 500mA and is set constant with a circuit. The voltage will be",
"design a heat block without cartridge heater? My idea is to build a"
] |
[
"way to convert a 3D print file, like STL, to STEP - a",
"file, like STL, to STEP - a useable file format for plastic injection",
"STP or STEP file. If there’s no easy way to convert it, which",
"convert it, which I don’t think there is, does anyone know someone good",
"to convert the files through a couple of programs without success. The most",
"way to convert it, which I don’t think there is, does anyone know",
"to convert it, which I don’t think there is, does anyone know someone",
"a good way to convert a 3D print file, like STL, to STEP",
"useable file format for plastic injection molding companies? I have tried to convert",
"STEP file. If there’s no easy way to convert it, which I don’t",
"know of a good way to convert a 3D print file, like STL,",
"programs without success. The most requested file is a STP or STEP file.",
"to STEP - a useable file format for plastic injection molding companies? I",
"print file, like STL, to STEP - a useable file format for plastic",
"If there’s no easy way to convert it, which I don’t think there",
"of programs without success. The most requested file is a STP or STEP",
"easy way to convert it, which I don’t think there is, does anyone",
"most requested file is a STP or STEP file. If there’s no easy",
"files through a couple of programs without success. The most requested file is",
"- a useable file format for plastic injection molding companies? I have tried",
"convert a 3D print file, like STL, to STEP - a useable file",
"for plastic injection molding companies? I have tried to convert the files through",
"have tried to convert the files through a couple of programs without success.",
"plastic injection molding companies? I have tried to convert the files through a",
"injection molding companies? I have tried to convert the files through a couple",
"requested file is a STP or STEP file. If there’s no easy way",
"STL, to STEP - a useable file format for plastic injection molding companies?",
"molding companies? I have tried to convert the files through a couple of",
"is a STP or STEP file. If there’s no easy way to convert",
"no easy way to convert it, which I don’t think there is, does",
"don’t think there is, does anyone know someone good at re-creating CAD files?",
"of a good way to convert a 3D print file, like STL, to",
"through a couple of programs without success. The most requested file is a",
"anyone know of a good way to convert a 3D print file, like",
"a 3D print file, like STL, to STEP - a useable file format",
"which I don’t think there is, does anyone know someone good at re-creating",
"it, which I don’t think there is, does anyone know someone good at",
"couple of programs without success. The most requested file is a STP or",
"good way to convert a 3D print file, like STL, to STEP -",
"The most requested file is a STP or STEP file. If there’s no",
"a STP or STEP file. If there’s no easy way to convert it,",
"tried to convert the files through a couple of programs without success. The",
"file. If there’s no easy way to convert it, which I don’t think",
"to convert a 3D print file, like STL, to STEP - a useable",
"without success. The most requested file is a STP or STEP file. If",
"file is a STP or STEP file. If there’s no easy way to",
"convert the files through a couple of programs without success. The most requested",
"I don’t think there is, does anyone know someone good at re-creating CAD",
"companies? I have tried to convert the files through a couple of programs",
"I have tried to convert the files through a couple of programs without",
"there’s no easy way to convert it, which I don’t think there is,",
"file format for plastic injection molding companies? I have tried to convert the",
"3D print file, like STL, to STEP - a useable file format for",
"success. The most requested file is a STP or STEP file. If there’s",
"STEP - a useable file format for plastic injection molding companies? I have",
"format for plastic injection molding companies? I have tried to convert the files",
"or STEP file. If there’s no easy way to convert it, which I",
"Does anyone know of a good way to convert a 3D print file,",
"like STL, to STEP - a useable file format for plastic injection molding",
"the files through a couple of programs without success. The most requested file",
"a useable file format for plastic injection molding companies? I have tried to",
"a couple of programs without success. The most requested file is a STP"
] |
[
"supply, I am getting the thermal protection message when heating my bed with",
"at 100/101). link to a video showing panel: <https://photos.app.goo.gl/jiW9NE7wEB4H0mOy1> [](https://i.stack.imgur.com/l3D0P.jpg)",
"getting the thermal protection message when heating my bed with target temperature set",
"message when heating my bed with target temperature set to 115 degrees. The",
"heating my bed with target temperature set to 115 degrees. The process slows",
"103 degrees (usually shutdown was at 100/101). link to a video showing panel:",
"bed with target temperature set to 115 degrees. The process slows down after",
"I changed merlin settings to trigger thermal shutdown after 5minutes/2degrees and added a",
"I am getting the thermal protection message when heating my bed with target",
"shutdown after 5minutes/2degrees and added a cover to the printer, so getting now",
"protection message when heating my bed with target temperature set to 115 degrees.",
"115 degrees. The process slows down after reaching 90. I changed merlin settings",
"90. I changed merlin settings to trigger thermal shutdown after 5minutes/2degrees and added",
"to trigger thermal shutdown after 5minutes/2degrees and added a cover to the printer,",
"after 5minutes/2degrees and added a cover to the printer, so getting now 103",
"my bed with target temperature set to 115 degrees. The process slows down",
"12Volt power supply, I am getting the thermal protection message when heating my",
"cover to the printer, so getting now 103 degrees (usually shutdown was at",
"power supply, I am getting the thermal protection message when heating my bed",
"degrees. The process slows down after reaching 90. I changed merlin settings to",
"large bed 12Volt power supply, I am getting the thermal protection message when",
"process slows down after reaching 90. I changed merlin settings to trigger thermal",
"I am having problems with my tevo tarantula large bed 12Volt power supply,",
"shutdown was at 100/101). link to a video showing panel: <https://photos.app.goo.gl/jiW9NE7wEB4H0mOy1> [![printer under",
"and added a cover to the printer, so getting now 103 degrees (usually",
"to the printer, so getting now 103 degrees (usually shutdown was at 100/101).",
"with target temperature set to 115 degrees. The process slows down after reaching",
"the printer, so getting now 103 degrees (usually shutdown was at 100/101). link",
"am having problems with my tevo tarantula large bed 12Volt power supply, I",
"trigger thermal shutdown after 5minutes/2degrees and added a cover to the printer, so",
"thermal protection message when heating my bed with target temperature set to 115",
"problems with my tevo tarantula large bed 12Volt power supply, I am getting",
"with my tevo tarantula large bed 12Volt power supply, I am getting the",
"bed 12Volt power supply, I am getting the thermal protection message when heating",
"down after reaching 90. I changed merlin settings to trigger thermal shutdown after",
"after reaching 90. I changed merlin settings to trigger thermal shutdown after 5minutes/2degrees",
"slows down after reaching 90. I changed merlin settings to trigger thermal shutdown",
"my tevo tarantula large bed 12Volt power supply, I am getting the thermal",
"target temperature set to 115 degrees. The process slows down after reaching 90.",
"printer, so getting now 103 degrees (usually shutdown was at 100/101). link to",
"now 103 degrees (usually shutdown was at 100/101). link to a video showing",
"was at 100/101). link to a video showing panel: <https://photos.app.goo.gl/jiW9NE7wEB4H0mOy1> [![printer under the",
"to 115 degrees. The process slows down after reaching 90. I changed merlin",
"settings to trigger thermal shutdown after 5minutes/2degrees and added a cover to the",
"the thermal protection message when heating my bed with target temperature set to",
"reaching 90. I changed merlin settings to trigger thermal shutdown after 5minutes/2degrees and",
"added a cover to the printer, so getting now 103 degrees (usually shutdown",
"a cover to the printer, so getting now 103 degrees (usually shutdown was",
"getting now 103 degrees (usually shutdown was at 100/101). link to a video",
"so getting now 103 degrees (usually shutdown was at 100/101). link to a",
"degrees (usually shutdown was at 100/101). link to a video showing panel: <https://photos.app.goo.gl/jiW9NE7wEB4H0mOy1>",
"temperature set to 115 degrees. The process slows down after reaching 90. I",
"tarantula large bed 12Volt power supply, I am getting the thermal protection message"
] |
[
"in slic3er at all for the extruder? or would I have to download",
"change the settings in slic3er at all for the extruder? or would I",
"a 5mm lead screw with a 1mm pitch. What is the easiest way",
"the existing extruder motor has now been attached to a 5mm lead screw",
"What is the easiest way to control the extruding of the printer now.",
"the extruder? or would I have to download and edit the marlin firmware?",
"that the existing extruder motor has now been attached to a 5mm lead",
"been attached to a 5mm lead screw with a 1mm pitch. What is",
"the easiest way to control the extruding of the printer now. For example",
"i3 MK2 printer so that the existing extruder motor has now been attached",
"has now been attached to a 5mm lead screw with a 1mm pitch.",
"at all for the extruder? or would I have to download and edit",
"is the easiest way to control the extruding of the printer now. For",
"printer now. For example is it possible to change the settings in slic3er",
"to control the extruding of the printer now. For example is it possible",
"way to control the extruding of the printer now. For example is it",
"5mm lead screw with a 1mm pitch. What is the easiest way to",
"control the extruding of the printer now. For example is it possible to",
"attached to a 5mm lead screw with a 1mm pitch. What is the",
"lead screw with a 1mm pitch. What is the easiest way to control",
"of the printer now. For example is it possible to change the settings",
"settings in slic3er at all for the extruder? or would I have to",
"all for the extruder? or would I have to download and edit the",
"extruding of the printer now. For example is it possible to change the",
"screw with a 1mm pitch. What is the easiest way to control the",
"now been attached to a 5mm lead screw with a 1mm pitch. What",
"my Prusa i3 MK2 printer so that the existing extruder motor has now",
"it possible to change the settings in slic3er at all for the extruder?",
"1mm pitch. What is the easiest way to control the extruding of the",
"with a 1mm pitch. What is the easiest way to control the extruding",
"Prusa i3 MK2 printer so that the existing extruder motor has now been",
"a 1mm pitch. What is the easiest way to control the extruding of",
"modified my Prusa i3 MK2 printer so that the existing extruder motor has",
"the printer now. For example is it possible to change the settings in",
"for the extruder? or would I have to download and edit the marlin",
"the extruding of the printer now. For example is it possible to change",
"the settings in slic3er at all for the extruder? or would I have",
"I have modified my Prusa i3 MK2 printer so that the existing extruder",
"MK2 printer so that the existing extruder motor has now been attached to",
"have modified my Prusa i3 MK2 printer so that the existing extruder motor",
"so that the existing extruder motor has now been attached to a 5mm",
"to a 5mm lead screw with a 1mm pitch. What is the easiest",
"motor has now been attached to a 5mm lead screw with a 1mm",
"slic3er at all for the extruder? or would I have to download and",
"possible to change the settings in slic3er at all for the extruder? or",
"now. For example is it possible to change the settings in slic3er at",
"pitch. What is the easiest way to control the extruding of the printer",
"is it possible to change the settings in slic3er at all for the",
"existing extruder motor has now been attached to a 5mm lead screw with",
"For example is it possible to change the settings in slic3er at all",
"printer so that the existing extruder motor has now been attached to a",
"example is it possible to change the settings in slic3er at all for",
"extruder motor has now been attached to a 5mm lead screw with a",
"easiest way to control the extruding of the printer now. For example is",
"to change the settings in slic3er at all for the extruder? or would"
] |
[
"6.5\"). Where can I find a heatbed that fits and a corresponding power",
"the da Vinci mini w with the proper dimensions (165 mm x 165",
"I find a heatbed that fits and a corresponding power supply / PID",
"mini w with the proper dimensions (165 mm x 165 mm or 6.5\"",
"to retrofit a heatbed to the da Vinci mini w with the proper",
"(165 mm x 165 mm or 6.5\" x 6.5\"). Where can I find",
"dimensions (165 mm x 165 mm or 6.5\" x 6.5\"). Where can I",
"Where can I find a heatbed that fits and a corresponding power supply",
"a heatbed to the da Vinci mini w with the proper dimensions (165",
"Vinci mini w with the proper dimensions (165 mm x 165 mm or",
"tried to retrofit a heatbed to the da Vinci mini w with the",
"mm x 165 mm or 6.5\" x 6.5\"). Where can I find a",
"heatbed to the da Vinci mini w with the proper dimensions (165 mm",
"with the proper dimensions (165 mm x 165 mm or 6.5\" x 6.5\").",
"w with the proper dimensions (165 mm x 165 mm or 6.5\" x",
"retrofit a heatbed to the da Vinci mini w with the proper dimensions",
"x 6.5\"). Where can I find a heatbed that fits and a corresponding",
"the proper dimensions (165 mm x 165 mm or 6.5\" x 6.5\"). Where",
"6.5\" x 6.5\"). Where can I find a heatbed that fits and a",
"mm or 6.5\" x 6.5\"). Where can I find a heatbed that fits",
"find a heatbed that fits and a corresponding power supply / PID controller?",
"can I find a heatbed that fits and a corresponding power supply /",
"to the da Vinci mini w with the proper dimensions (165 mm x",
"Anybody ever tried to retrofit a heatbed to the da Vinci mini w",
"proper dimensions (165 mm x 165 mm or 6.5\" x 6.5\"). Where can",
"da Vinci mini w with the proper dimensions (165 mm x 165 mm",
"or 6.5\" x 6.5\"). Where can I find a heatbed that fits and",
"ever tried to retrofit a heatbed to the da Vinci mini w with",
"x 165 mm or 6.5\" x 6.5\"). Where can I find a heatbed",
"165 mm or 6.5\" x 6.5\"). Where can I find a heatbed that"
] |
[
"the drive gear. This was a genuine Titan Aero extruder, 0.4mm nozzle, 215C",
"lots of short dead-end, not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg)",
"to have stopped moving, and was cut through by the drive gear. This",
"short dead-end, not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament",
"drive gear. This was a genuine Titan Aero extruder, 0.4mm nozzle, 215C (on",
"through by the drive gear. This was a genuine Titan Aero extruder, 0.4mm",
"a couple of hours in. I was wondering if the nature of the",
"filament seemed to have stopped moving, and was cut through by the drive",
"failed a couple of hours in. I was wondering if the nature of",
"a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped",
"not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to",
"surface has lots of short dead-end, not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have",
"has lots of short dead-end, not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The",
"it's just bad luck? To be clear, the surface has lots of short",
"contributed to the clog, or if it's just bad luck? To be clear,",
"luck? To be clear, the surface has lots of short dead-end, not just",
"with lots of retracts (similarly the previous print which was OK) might have",
"a genuine Titan Aero extruder, 0.4mm nozzle, 215C (on an Anet a8 printer)",
"if it's just bad luck? To be clear, the surface has lots of",
"print failed a couple of hours in. I was wondering if the nature",
"bad luck? To be clear, the surface has lots of short dead-end, not",
"or if it's just bad luck? To be clear, the surface has lots",
"couple of hours in. I was wondering if the nature of the print",
"just bad luck? To be clear, the surface has lots of short dead-end,",
"was OK) might have contributed to the clog, or if it's just bad",
"retracts (similarly the previous print which was OK) might have contributed to the",
"This print failed a couple of hours in. I was wondering if the",
"stopped moving, and was cut through by the drive gear. This was a",
"of retracts (similarly the previous print which was OK) might have contributed to",
"of hours in. I was wondering if the nature of the print surface,",
"which was OK) might have contributed to the clog, or if it's just",
"here](https://i.stack.imgur.com/iymMN.jpg)](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving, and was cut through by",
"the print surface, with lots of retracts (similarly the previous print which was",
"(similarly the previous print which was OK) might have contributed to the clog,",
"lots of retracts (similarly the previous print which was OK) might have contributed",
"the nature of the print surface, with lots of retracts (similarly the previous",
"wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving,",
"hours in. I was wondering if the nature of the print surface, with",
"The filament seemed to have stopped moving, and was cut through by the",
"seemed to have stopped moving, and was cut through by the drive gear.",
"description here](https://i.stack.imgur.com/iymMN.jpg)](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving, and was cut through",
"by the drive gear. This was a genuine Titan Aero extruder, 0.4mm nozzle,",
"gear. This was a genuine Titan Aero extruder, 0.4mm nozzle, 215C (on an",
"was a genuine Titan Aero extruder, 0.4mm nozzle, 215C (on an Anet a8",
"To be clear, the surface has lots of short dead-end, not just a",
"perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving, and",
"print surface, with lots of retracts (similarly the previous print which was OK)",
"the surface has lots of short dead-end, not just a wiggly perimeter. [](https://i.stack.imgur.com/iymMN.jpg) The filament seemed",
"if the nature of the print surface, with lots of retracts (similarly the",
"clog, or if it's just bad luck? To be clear, the surface has",
"might have contributed to the clog, or if it's just bad luck? To",
"[](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving, and was",
"have contributed to the clog, or if it's just bad luck? To be",
"print which was OK) might have contributed to the clog, or if it's",
"in. I was wondering if the nature of the print surface, with lots",
"previous print which was OK) might have contributed to the clog, or if",
"image description here](https://i.stack.imgur.com/iymMN.jpg)](https://i.stack.imgur.com/iymMN.jpg) The filament seemed to have stopped moving, and was cut",
"have stopped moving, and was cut through by the drive gear. This was",
"be clear, the surface has lots of short dead-end, not just a wiggly",
"the previous print which was OK) might have contributed to the clog, or",
"nature of the print surface, with lots of retracts (similarly the previous print"
] |
[
"be located outside of the US. Can anyone direct me to a seller",
"After doing a lot of research, I've decided I want to purchase a",
"than Amazon, which seems to have a bit of a mark-up on price,",
"finding several websites that seem to be located outside of the US. Can",
"a reputable, local seller. Other than Amazon, which seems to have a bit",
"of the US. Can anyone direct me to a seller located in the",
"a Creality CR-10S as my first 3D printer. I'm trying to locate a",
"Amazon, which seems to have a bit of a mark-up on price, I'm",
"my first 3D printer. I'm trying to locate a reputable, local seller. Other",
"doing a lot of research, I've decided I want to purchase a Creality",
"printer. I'm trying to locate a reputable, local seller. Other than Amazon, which",
"3D printer. I'm trying to locate a reputable, local seller. Other than Amazon,",
"locate a reputable, local seller. Other than Amazon, which seems to have a",
"mark-up on price, I'm finding several websites that seem to be located outside",
"on price, I'm finding several websites that seem to be located outside of",
"seller. Other than Amazon, which seems to have a bit of a mark-up",
"as my first 3D printer. I'm trying to locate a reputable, local seller.",
"to have a bit of a mark-up on price, I'm finding several websites",
"which seems to have a bit of a mark-up on price, I'm finding",
"to locate a reputable, local seller. Other than Amazon, which seems to have",
"CR-10S as my first 3D printer. I'm trying to locate a reputable, local",
"seems to have a bit of a mark-up on price, I'm finding several",
"a mark-up on price, I'm finding several websites that seem to be located",
"of research, I've decided I want to purchase a Creality CR-10S as my",
"I'm finding several websites that seem to be located outside of the US.",
"bit of a mark-up on price, I'm finding several websites that seem to",
"trying to locate a reputable, local seller. Other than Amazon, which seems to",
"outside of the US. Can anyone direct me to a seller located in",
"price, I'm finding several websites that seem to be located outside of the",
"I've decided I want to purchase a Creality CR-10S as my first 3D",
"have a bit of a mark-up on price, I'm finding several websites that",
"a bit of a mark-up on price, I'm finding several websites that seem",
"the US. Can anyone direct me to a seller located in the US?",
"I'm trying to locate a reputable, local seller. Other than Amazon, which seems",
"to purchase a Creality CR-10S as my first 3D printer. I'm trying to",
"decided I want to purchase a Creality CR-10S as my first 3D printer.",
"lot of research, I've decided I want to purchase a Creality CR-10S as",
"purchase a Creality CR-10S as my first 3D printer. I'm trying to locate",
"to be located outside of the US. Can anyone direct me to a",
"first 3D printer. I'm trying to locate a reputable, local seller. Other than",
"websites that seem to be located outside of the US. Can anyone direct",
"I want to purchase a Creality CR-10S as my first 3D printer. I'm",
"Other than Amazon, which seems to have a bit of a mark-up on",
"want to purchase a Creality CR-10S as my first 3D printer. I'm trying",
"seem to be located outside of the US. Can anyone direct me to",
"several websites that seem to be located outside of the US. Can anyone",
"that seem to be located outside of the US. Can anyone direct me",
"located outside of the US. Can anyone direct me to a seller located",
"reputable, local seller. Other than Amazon, which seems to have a bit of",
"Creality CR-10S as my first 3D printer. I'm trying to locate a reputable,",
"a lot of research, I've decided I want to purchase a Creality CR-10S",
"local seller. Other than Amazon, which seems to have a bit of a",
"of a mark-up on price, I'm finding several websites that seem to be",
"research, I've decided I want to purchase a Creality CR-10S as my first"
] |
[
"for the Z axis, I have an M8 lead screw with 8 mm",
"instead of M5. What do you think about it? What should I keep",
"available online I could just use them instead of M5. What do you",
"I find it very difficult to find M5 rods for the Z axis,",
"M5 rods for the Z axis, I have an M8 lead screw with",
"I could just use them instead of M5. What do you think about",
"find it very difficult to find M5 rods for the Z axis, I",
"screw with 8 mm lead, So I thought since M8 is widely available",
"MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find M5 rods for the",
"a Prusa i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find M5",
"is widely available online I could just use them instead of M5. What",
"difficult to find M5 rods for the Z axis, I have an M8",
"I have an M8 lead screw with 8 mm lead, So I thought",
"with 8 mm lead, So I thought since M8 is widely available online",
"Z axis, I have an M8 lead screw with 8 mm lead, So",
"very difficult to find M5 rods for the Z axis, I have an",
"M5. What do you think about it? What should I keep in mind?",
"([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find M5 rods for the Z",
"rods for the Z axis, I have an M8 lead screw with 8",
"the Z axis, I have an M8 lead screw with 8 mm lead,",
"I thought since M8 is widely available online I could just use them",
"could just use them instead of M5. What do you think about it?",
"find M5 rods for the Z axis, I have an M8 lead screw",
"to find M5 rods for the Z axis, I have an M8 lead",
"them instead of M5. What do you think about it? What should I",
"M8 is widely available online I could just use them instead of M5.",
"lead screw with 8 mm lead, So I thought since M8 is widely",
"an M8 lead screw with 8 mm lead, So I thought since M8",
"mm lead, So I thought since M8 is widely available online I could",
"building a Prusa i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find",
"axis, I have an M8 lead screw with 8 mm lead, So I",
"So I thought since M8 is widely available online I could just use",
"Prusa i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find M5 rods",
"it very difficult to find M5 rods for the Z axis, I have",
"use them instead of M5. What do you think about it? What should",
"have an M8 lead screw with 8 mm lead, So I thought since",
"since M8 is widely available online I could just use them instead of",
"I am building a Prusa i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult",
"lead, So I thought since M8 is widely available online I could just",
"widely available online I could just use them instead of M5. What do",
"thought since M8 is widely available online I could just use them instead",
"just use them instead of M5. What do you think about it? What",
"M8 lead screw with 8 mm lead, So I thought since M8 is",
"am building a Prusa i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to",
"i3 MK2S ([Dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/)). I find it very difficult to find M5 rods for",
"online I could just use them instead of M5. What do you think",
"of M5. What do you think about it? What should I keep in",
"8 mm lead, So I thought since M8 is widely available online I"
] |
[
"Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3, *Gcode",
"getting seemingly random lines scattered across the top surface of my prints: ",
"Cura 3.2.1 Printer chosen in Cura: Prusa i3, *Gcode flavor* changed to *RepRap*",
"  Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura:",
"top surface of my prints:   Printer: Anycubic i3 mega Slicer: Cura",
"lines scattered across the top surface of my prints:   Printer: Anycubic",
"Prusa i3, *Gcode flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer before inner",
"seemingly random lines scattered across the top surface of my prints:  ",
"Cura Profile: *Fine*, \"Outer before inner walls\" enabled What might be the reason?",
" Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa",
"mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3, *Gcode flavor* changed",
"i3, *Gcode flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer before inner walls\"",
"prints:   Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in",
"i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3, *Gcode flavor*",
"of my prints:   Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer",
"my prints:   Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen",
"chosen in Cura: Prusa i3, *Gcode flavor* changed to *RepRap* Cura Profile: *Fine*,",
"*RepRap* Cura Profile: *Fine*, \"Outer before inner walls\" enabled What might be the",
"Printer chosen in Cura: Prusa i3, *Gcode flavor* changed to *RepRap* Cura Profile:",
"Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3, *Gcode flavor* changed to",
"3.2.1 Printer chosen in Cura: Prusa i3, *Gcode flavor* changed to *RepRap* Cura",
"I'm getting seemingly random lines scattered across the top surface of my prints:",
"random lines scattered across the top surface of my prints:   Printer:",
"flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer before inner walls\" enabled What",
"changed to *RepRap* Cura Profile: *Fine*, \"Outer before inner walls\" enabled What might",
"to *RepRap* Cura Profile: *Fine*, \"Outer before inner walls\" enabled What might be",
"surface of my prints:   Printer: Anycubic i3 mega Slicer: Cura 3.2.1",
"scattered across the top surface of my prints:   Printer: Anycubic i3",
"the top surface of my prints:   Printer: Anycubic i3 mega Slicer:",
"*Gcode flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer before inner walls\" enabled",
"across the top surface of my prints:   Printer: Anycubic i3 mega",
"Cura: Prusa i3, *Gcode flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer before",
"in Cura: Prusa i3, *Gcode flavor* changed to *RepRap* Cura Profile: *Fine*, \"Outer",
"Printer: Anycubic i3 mega Slicer: Cura 3.2.1 Printer chosen in Cura: Prusa i3,"
] |
[
"called [TinkerCAD](http://www.tinkercad.com), which lets you export your design in either STL or OBJ",
"STL or OBJ form. What is the difference between these two file types?",
"I use is called [TinkerCAD](http://www.tinkercad.com), which lets you export your design in either",
"form. What is the difference between these two file types? And which one",
"One of the CAD programs I use is called [TinkerCAD](http://www.tinkercad.com), which lets you",
"[TinkerCAD](http://www.tinkercad.com), which lets you export your design in either STL or OBJ form.",
"What is the difference between these two file types? And which one is",
"the CAD programs I use is called [TinkerCAD](http://www.tinkercad.com), which lets you export your",
"is the difference between these two file types? And which one is better",
"design in either STL or OBJ form. What is the difference between these",
"lets you export your design in either STL or OBJ form. What is",
"OBJ form. What is the difference between these two file types? And which",
"use is called [TinkerCAD](http://www.tinkercad.com), which lets you export your design in either STL",
"of the CAD programs I use is called [TinkerCAD](http://www.tinkercad.com), which lets you export",
"programs I use is called [TinkerCAD](http://www.tinkercad.com), which lets you export your design in",
"export your design in either STL or OBJ form. What is the difference",
"in either STL or OBJ form. What is the difference between these two",
"either STL or OBJ form. What is the difference between these two file",
"difference between these two file types? And which one is better to use?",
"the difference between these two file types? And which one is better to",
"or OBJ form. What is the difference between these two file types? And",
"your design in either STL or OBJ form. What is the difference between",
"is called [TinkerCAD](http://www.tinkercad.com), which lets you export your design in either STL or",
"you export your design in either STL or OBJ form. What is the",
"which lets you export your design in either STL or OBJ form. What",
"CAD programs I use is called [TinkerCAD](http://www.tinkercad.com), which lets you export your design"
] |
[
"A paper which answers this unambiguously would be the ideal answer to this",
"as for joints. What about other applications where load bearing properties are not",
"(extrusion based 3D printer) materials, such as ABS or PLA (or slightly more",
"as kevlar, fibreglass, or carbon fiber), safe for implantation in the human body?",
"is similar: [Are there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears",
"mechanical issues as a result of the 3D printing process itself. However, it",
"issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane",
"adverse host responses is more crucial, e.g. causing inflammation or it being a",
"with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I found a paper describing",
"useful in applications where strength is required, such as for joints. What about",
"If not, why not? If most of them are safe, then please explain",
"Another concern is if the process of 3D printing itself adversely influences the",
"the 3D printing process itself. However, it is not clear to me if",
"are safe for implantation in the human body? A paper which answers this",
"inflammation or it being a bacterial growth substrate to promote infections seems like",
"NOT safe. Highly relevant, and perhaps even more interesting is: Are there any",
"which I'm not aware of. I found a paper dealing with corrosion issues",
"materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use.",
"of the 3D printing process itself. However, it is not clear to me",
"to this question. Another concern is if the process of 3D printing itself",
"and history of ultra-high molecular weight polyethylene (UHMWPE), which appears to be commonly",
"exotic ones, such as kevlar, fibreglass, or carbon fiber), safe for implantation in",
"be frequently used for implants, and while titanium 3D printers do exist, they",
"10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE might be safe, barring any",
"any papers or studies which answer it. I can easily find that ABS",
"implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane being prone",
"10.1021/ma301965y I found a paper describing the properties and history of ultra-high molecular",
"which answers this unambiguously would be the ideal answer to this question. Another",
"and while titanium 3D printers do exist, they are beyond the scope of",
"implantation in the human body? Or in medical terms, are they biocompatible (biofunctionality",
"sub $10,000 range (arbitrarily chosen to make the question avoid being tagged as",
"for non-implantation use. This question is for materials intended to be implanted. Are",
"a paper dealing with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found",
"the human body? A paper which answers this unambiguously would be the ideal",
"materials, such as ABS or PLA (or slightly more exotic ones, such as",
"properties of the material in the context of implantation applications. I've tried to",
"slightly more exotic ones, such as kevlar, fibreglass, or carbon fiber), safe for",
"me if any 3D printers can actually reliably print UHMWPE. Furthermore, it is",
"that titanium appears to be frequently used for implants, and while titanium 3D",
"based 3D printer) materials, such as ABS or PLA (or slightly more exotic",
"easily find that ABS plastic is \"non-biodegradable\", but I suppose the issue of",
"typical 3D printed (extrusion based 3D printer) materials, such as ABS or PLA",
"found a paper describing the properties and history of ultra-high molecular weight polyethylene",
"other dangerous complications too, which I'm not aware of. I found a paper",
"concern is if the process of 3D printing itself adversely influences the properties",
"context is extrusion based 3D printers in the sub $10,000 range (arbitrarily chosen",
"unambiguously would be the ideal answer to this question. Another concern is if",
"of implantation applications. I've tried to determine the answer to this question myself,",
"causing inflammation or it being a bacterial growth substrate to promote infections seems",
"to be frequently used for implants, and while titanium 3D printers do exist,",
"implanted. Are any typical 3D printed (extrusion based 3D printer) materials, such as",
"or PLA (or slightly more exotic ones, such as kevlar, fibreglass, or carbon",
"peer reviewed medical papers that have investigated what materials are safe for implantation",
"I'm not aware of. I found a paper dealing with corrosion issues for",
"the answer to this question myself, but I cannot find any papers or",
"clear to me if any 3D printers can actually reliably print UHMWPE. Furthermore,",
"context of implantation applications. I've tried to determine the answer to this question",
"process itself. However, it is not clear to me if any 3D printers",
"PLA (or slightly more exotic ones, such as kevlar, fibreglass, or carbon fiber),",
"3D printing itself adversely influences the properties of the material in the context",
"such as ABS or PLA (or slightly more exotic ones, such as kevlar,",
"commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE",
"By extension, a 3D printer using UHMWPE might be safe, barring any adverse",
"they biocompatible (biofunctionality is not topical for this question)? If not, why not?",
"paper dealing with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I found a",
"but I cannot find any papers or studies which answer it. I can",
"reliably print UHMWPE. Furthermore, it is unclear if UHMWPE is a sane choice,",
"safe, barring any adverse chemical or mechanical issues as a result of the",
"being a bacterial growth substrate to promote infections seems like plausible concerns. I'm",
"implantable electronics)? I'm aware that titanium appears to be frequently used for implants,",
"\"non-biodegradable\", but I suppose the issue of adverse host responses is more crucial,",
"might be other dangerous complications too, which I'm not aware of. I found",
"if the process of 3D printing itself adversely influences the properties of the",
"weight polyethylene (UHMWPE), which appears to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331",
"or studies which answer it. I can easily find that ABS plastic is",
"DOI: 10.1021/ma301965y I found a paper describing the properties and history of ultra-high",
"that ABS plastic is \"non-biodegradable\", but I suppose the issue of adverse host",
"suppose the issue of adverse host responses is more crucial, e.g. causing inflammation",
"to me if any 3D printers can actually reliably print UHMWPE. Furthermore, it",
"non-implantation use. This question is for materials intended to be implanted. Are any",
"a simple enclosure for implantable electronics)? I'm aware that titanium appears to be",
"be implanted. Are any typical 3D printed (extrusion based 3D printer) materials, such",
"process of 3D printing itself adversely influences the properties of the material in",
"printer using UHMWPE might be safe, barring any adverse chemical or mechanical issues",
"if any 3D printers can actually reliably print UHMWPE. Furthermore, it is unclear",
"can actually reliably print UHMWPE. Furthermore, it is unclear if UHMWPE is a",
"promote infections seems like plausible concerns. I'm sure there might be other dangerous",
"other applications where load bearing properties are not required (e.g. a simple enclosure",
"body? Or in medical terms, are they biocompatible (biofunctionality is not topical for",
"most of them are safe, then please explain which ones are NOT safe.",
"The valid context is extrusion based 3D printers in the sub $10,000 range",
"adverse chemical or mechanical issues as a result of the 3D printing process",
"itself. However, it is not clear to me if any 3D printers can",
"the ideal answer to this question. Another concern is if the process of",
"is not clear to me if any 3D printers can actually reliably print",
"prone to breakdown: DOI: 10.1021/ma301965y I found a paper describing the properties and",
"Are any typical 3D printed (extrusion based 3D printer) materials, such as ABS",
"titanium appears to be frequently used for implants, and while titanium 3D printers",
"printer) materials, such as ABS or PLA (or slightly more exotic ones, such",
"3D printers can actually reliably print UHMWPE. Furthermore, it is unclear if UHMWPE",
"are they biocompatible (biofunctionality is not topical for this question)? If not, why",
"complications too, which I'm not aware of. I found a paper dealing with",
"studies which answer it. I can easily find that ABS plastic is \"non-biodegradable\",",
"are beyond the scope of this question. The valid context is extrusion based",
"UHMWPE. Furthermore, it is unclear if UHMWPE is a sane choice, as it",
"ones are NOT safe. Highly relevant, and perhaps even more interesting is: Are",
"enclosure for implantable electronics)? I'm aware that titanium appears to be frequently used",
"properties are not required (e.g. a simple enclosure for implantable electronics)? I'm aware",
"it is unclear if UHMWPE is a sane choice, as it appears to",
"print UHMWPE. Furthermore, it is unclear if UHMWPE is a sane choice, as",
"medical terms, are they biocompatible (biofunctionality is not topical for this question)? If",
"to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer",
"used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE might",
"for implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane being",
"10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane being prone to breakdown: DOI:",
"question is for materials intended to be implanted. Are any typical 3D printed",
"in the sub $10,000 range (arbitrarily chosen to make the question avoid being",
"cannot find any papers or studies which answer it. I can easily find",
"appears to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D",
"papers or studies which answer it. I can easily find that ABS plastic",
"appears to be frequently used for implants, and while titanium 3D printers do",
"plastic is \"non-biodegradable\", but I suppose the issue of adverse host responses is",
"DOI: 10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane being prone to breakdown:",
"but I suppose the issue of adverse host responses is more crucial, e.g.",
"This question is similar: [Are there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public)",
"printing process itself. However, it is not clear to me if any 3D",
"required, such as for joints. What about other applications where load bearing properties",
"sure there might be other dangerous complications too, which I'm not aware of.",
"being prone to breakdown: DOI: 10.1021/ma301965y I found a paper describing the properties",
"growth substrate to promote infections seems like plausible concerns. I'm sure there might",
"is more crucial, e.g. causing inflammation or it being a bacterial growth substrate",
"the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use. This question is",
"printing itself adversely influences the properties of the material in the context of",
"be the ideal answer to this question. Another concern is if the process",
"not required (e.g. a simple enclosure for implantable electronics)? I'm aware that titanium",
"metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing with silicone-urethane being prone to",
"materials intended to be implanted. Are any typical 3D printed (extrusion based 3D",
"materials are safe for implantation in the human body? A paper which answers",
"this question. Another concern is if the process of 3D printing itself adversely",
"myself, but I cannot find any papers or studies which answer it. I",
"3D printed (extrusion based 3D printer) materials, such as ABS or PLA (or",
"is \"non-biodegradable\", but I suppose the issue of adverse host responses is more",
"host responses is more crucial, e.g. causing inflammation or it being a bacterial",
"are safe, then please explain which ones are NOT safe. Highly relevant, and",
"investigated what materials are safe for implantation in the human body? A paper",
"extrusion based 3D printers in the sub $10,000 range (arbitrarily chosen to make",
"ultra-high molecular weight polyethylene (UHMWPE), which appears to be commonly used as implants:",
"choice, as it appears to be useful in applications where strength is required,",
"while titanium 3D printers do exist, they are beyond the scope of this",
"is for materials intended to be implanted. Are any typical 3D printed (extrusion",
"this unambiguously would be the ideal answer to this question. Another concern is",
"implants, and while titanium 3D printers do exist, they are beyond the scope",
"such as kevlar, fibreglass, or carbon fiber), safe for implantation in the human",
"substrate to promote infections seems like plausible concerns. I'm sure there might be",
"UHMWPE is a sane choice, as it appears to be useful in applications",
"valid context is extrusion based 3D printers in the sub $10,000 range (arbitrarily",
"be for non-implantation use. This question is for materials intended to be implanted.",
"of 3D printing itself adversely influences the properties of the material in the",
"material in the context of implantation applications. I've tried to determine the answer",
"to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use. This question",
"there any peer reviewed medical papers that have investigated what materials are safe",
"found a paper dealing with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I",
"3D printer using UHMWPE might be safe, barring any adverse chemical or mechanical",
"are not required (e.g. a simple enclosure for implantable electronics)? I'm aware that",
"paper describing the properties and history of ultra-high molecular weight polyethylene (UHMWPE), which",
"But appears to be for non-implantation use. This question is for materials intended",
"any adverse chemical or mechanical issues as a result of the 3D printing",
"I found a paper describing the properties and history of ultra-high molecular weight",
"UHMWPE might be safe, barring any adverse chemical or mechanical issues as a",
"appears to be useful in applications where strength is required, such as for",
"perhaps even more interesting is: Are there any peer reviewed medical papers that",
"a result of the 3D printing process itself. However, it is not clear",
"aware that titanium appears to be frequently used for implants, and while titanium",
"be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using",
"to be useful in applications where strength is required, such as for joints.",
"they are beyond the scope of this question. The valid context is extrusion",
"be useful in applications where strength is required, such as for joints. What",
"tried to determine the answer to this question myself, but I cannot find",
"I'm sure there might be other dangerous complications too, which I'm not aware",
"not aware of. I found a paper dealing with corrosion issues for implantable",
"polyethylene (UHMWPE), which appears to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By",
"What about other applications where load bearing properties are not required (e.g. a",
"in medical terms, are they biocompatible (biofunctionality is not topical for this question)?",
"more exotic ones, such as kevlar, fibreglass, or carbon fiber), safe for implantation",
"public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use. This question is for materials",
"breakdown: DOI: 10.1021/ma301965y I found a paper describing the properties and history of",
"are NOT safe. Highly relevant, and perhaps even more interesting is: Are there",
"If most of them are safe, then please explain which ones are NOT",
"infections seems like plausible concerns. I'm sure there might be other dangerous complications",
"any peer reviewed medical papers that have investigated what materials are safe for",
"a paper describing the properties and history of ultra-high molecular weight polyethylene (UHMWPE),",
"[Are there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be",
"fiber), safe for implantation in the human body? Or in medical terms, are",
"the context of implantation applications. I've tried to determine the answer to this",
"(biofunctionality is not topical for this question)? If not, why not? If most",
"implantation applications. I've tried to determine the answer to this question myself, but",
"beyond the scope of this question. The valid context is extrusion based 3D",
"I found a paper dealing with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y",
"as a result of the 3D printing process itself. However, it is not",
"ones, such as kevlar, fibreglass, or carbon fiber), safe for implantation in the",
"or mechanical issues as a result of the 3D printing process itself. However,",
"Furthermore, it is unclear if UHMWPE is a sane choice, as it appears",
"in the context of implantation applications. I've tried to determine the answer to",
"printed (extrusion based 3D printer) materials, such as ABS or PLA (or slightly",
"about other applications where load bearing properties are not required (e.g. a simple",
"interesting is: Are there any peer reviewed medical papers that have investigated what",
"papers that have investigated what materials are safe for implantation in the human",
"a paper dealing with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I found",
"is if the process of 3D printing itself adversely influences the properties of",
"using UHMWPE might be safe, barring any adverse chemical or mechanical issues as",
"this question myself, but I cannot find any papers or studies which answer",
"or carbon fiber), safe for implantation in the human body? Or in medical",
"barring any adverse chemical or mechanical issues as a result of the 3D",
"too, which I'm not aware of. I found a paper dealing with corrosion",
"is a sane choice, as it appears to be useful in applications where",
"human body? A paper which answers this unambiguously would be the ideal answer",
"However, it is not clear to me if any 3D printers can actually",
"I'm aware that titanium appears to be frequently used for implants, and while",
"question. The valid context is extrusion based 3D printers in the sub $10,000",
"corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing with",
"as it appears to be useful in applications where strength is required, such",
"any 3D printers can actually reliably print UHMWPE. Furthermore, it is unclear if",
"any typical 3D printed (extrusion based 3D printer) materials, such as ABS or",
"load bearing properties are not required (e.g. a simple enclosure for implantable electronics)?",
"then please explain which ones are NOT safe. Highly relevant, and perhaps even",
"applications. I've tried to determine the answer to this question myself, but I",
"implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE might be safe,",
"3D printers do exist, they are beyond the scope of this question. The",
"actually reliably print UHMWPE. Furthermore, it is unclear if UHMWPE is a sane",
"Are there any peer reviewed medical papers that have investigated what materials are",
"there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for",
"to determine the answer to this question myself, but I cannot find any",
"paper which answers this unambiguously would be the ideal answer to this question.",
"crucial, e.g. causing inflammation or it being a bacterial growth substrate to promote",
"of ultra-high molecular weight polyethylene (UHMWPE), which appears to be commonly used as",
"(UHMWPE), which appears to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension,",
"to this question myself, but I cannot find any papers or studies which",
"this question)? If not, why not? If most of them are safe, then",
"would be the ideal answer to this question. Another concern is if the",
"as ABS or PLA (or slightly more exotic ones, such as kevlar, fibreglass,",
"not, why not? If most of them are safe, then please explain which",
"for implantation in the human body? A paper which answers this unambiguously would",
"required (e.g. a simple enclosure for implantable electronics)? I'm aware that titanium appears",
"simple enclosure for implantable electronics)? I'm aware that titanium appears to be frequently",
"biocompatible (biofunctionality is not topical for this question)? If not, why not? If",
"find that ABS plastic is \"non-biodegradable\", but I suppose the issue of adverse",
"determine the answer to this question myself, but I cannot find any papers",
"please explain which ones are NOT safe. Highly relevant, and perhaps even more",
"the process of 3D printing itself adversely influences the properties of the material",
"frequently used for implants, and while titanium 3D printers do exist, they are",
"titanium 3D printers do exist, they are beyond the scope of this question.",
"reviewed medical papers that have investigated what materials are safe for implantation in",
"bacterial growth substrate to promote infections seems like plausible concerns. I'm sure there",
"DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE might be safe, barring",
"history of ultra-high molecular weight polyethylene (UHMWPE), which appears to be commonly used",
"(or slightly more exotic ones, such as kevlar, fibreglass, or carbon fiber), safe",
"for materials intended to be implanted. Are any typical 3D printed (extrusion based",
"topical for this question)? If not, why not? If most of them are",
"of. I found a paper dealing with corrosion issues for implantable metals: DOI:",
"them are safe, then please explain which ones are NOT safe. Highly relevant,",
"(e.g. a simple enclosure for implantable electronics)? I'm aware that titanium appears to",
"safe for implantation in the human body? A paper which answers this unambiguously",
"applications where load bearing properties are not required (e.g. a simple enclosure for",
"exist, they are beyond the scope of this question. The valid context is",
"can easily find that ABS plastic is \"non-biodegradable\", but I suppose the issue",
"terms, are they biocompatible (biofunctionality is not topical for this question)? If not,",
"Highly relevant, and perhaps even more interesting is: Are there any peer reviewed",
"might be safe, barring any adverse chemical or mechanical issues as a result",
"explain which ones are NOT safe. Highly relevant, and perhaps even more interesting",
"find any papers or studies which answer it. I can easily find that",
"safe, then please explain which ones are NOT safe. Highly relevant, and perhaps",
"more interesting is: Are there any peer reviewed medical papers that have investigated",
"which answer it. I can easily find that ABS plastic is \"non-biodegradable\", but",
"similar: [Are there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to",
"strength is required, such as for joints. What about other applications where load",
"safe. Highly relevant, and perhaps even more interesting is: Are there any peer",
"influences the properties of the material in the context of implantation applications. I've",
"for implants, and while titanium 3D printers do exist, they are beyond the",
"a sane choice, as it appears to be useful in applications where strength",
"in the human body? A paper which answers this unambiguously would be the",
"more crucial, e.g. causing inflammation or it being a bacterial growth substrate to",
"aware of. I found a paper dealing with corrosion issues for implantable metals:",
"I found a paper dealing with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383",
"used for implants, and while titanium 3D printers do exist, they are beyond",
"where load bearing properties are not required (e.g. a simple enclosure for implantable",
"plausible concerns. I'm sure there might be other dangerous complications too, which I'm",
"ideal answer to this question. Another concern is if the process of 3D",
"for implantation in the human body? Or in medical terms, are they biocompatible",
"dangerous complications too, which I'm not aware of. I found a paper dealing",
"electronics)? I'm aware that titanium appears to be frequently used for implants, and",
"describing the properties and history of ultra-high molecular weight polyethylene (UHMWPE), which appears",
"question. Another concern is if the process of 3D printing itself adversely influences",
"itself adversely influences the properties of the material in the context of implantation",
"in applications where strength is required, such as for joints. What about other",
"ABS plastic is \"non-biodegradable\", but I suppose the issue of adverse host responses",
"is extrusion based 3D printers in the sub $10,000 range (arbitrarily chosen to",
"human body? Or in medical terms, are they biocompatible (biofunctionality is not topical",
"$10,000 range (arbitrarily chosen to make the question avoid being tagged as \"too",
"of this question. The valid context is extrusion based 3D printers in the",
"why not? If most of them are safe, then please explain which ones",
"as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a 3D printer using UHMWPE might be",
"of adverse host responses is more crucial, e.g. causing inflammation or it being",
"to promote infections seems like plausible concerns. I'm sure there might be other",
"seems like plausible concerns. I'm sure there might be other dangerous complications too,",
"chemical or mechanical issues as a result of the 3D printing process itself.",
"body? A paper which answers this unambiguously would be the ideal answer to",
"it is not clear to me if any 3D printers can actually reliably",
"and perhaps even more interesting is: Are there any peer reviewed medical papers",
"the sub $10,000 range (arbitrarily chosen to make the question avoid being tagged",
"what materials are safe for implantation in the human body? A paper which",
"a 3D printer using UHMWPE might be safe, barring any adverse chemical or",
"is required, such as for joints. What about other applications where load bearing",
"adversely influences the properties of the material in the context of implantation applications.",
"responses is more crucial, e.g. causing inflammation or it being a bacterial growth",
"implantation in the human body? A paper which answers this unambiguously would be",
"the properties and history of ultra-high molecular weight polyethylene (UHMWPE), which appears to",
"to breakdown: DOI: 10.1021/ma301965y I found a paper describing the properties and history",
"safe for implantation in the human body? Or in medical terms, are they",
"be other dangerous complications too, which I'm not aware of. I found a",
"use. This question is for materials intended to be implanted. Are any typical",
"biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation",
"found a paper dealing with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I",
"even more interesting is: Are there any peer reviewed medical papers that have",
"such as for joints. What about other applications where load bearing properties are",
"scope of this question. The valid context is extrusion based 3D printers in",
"is not topical for this question)? If not, why not? If most of",
"I cannot find any papers or studies which answer it. I can easily",
"question myself, but I cannot find any papers or studies which answer it.",
"range (arbitrarily chosen to make the question avoid being tagged as \"too broad\").",
"concerns. I'm sure there might be other dangerous complications too, which I'm not",
"I've tried to determine the answer to this question myself, but I cannot",
"it being a bacterial growth substrate to promote infections seems like plausible concerns.",
"like plausible concerns. I'm sure there might be other dangerous complications too, which",
"or it being a bacterial growth substrate to promote infections seems like plausible",
"printers in the sub $10,000 range (arbitrarily chosen to make the question avoid",
"e.g. causing inflammation or it being a bacterial growth substrate to promote infections",
"which ones are NOT safe. Highly relevant, and perhaps even more interesting is:",
"to be for non-implantation use. This question is for materials intended to be",
"fibreglass, or carbon fiber), safe for implantation in the human body? Or in",
"answer to this question. Another concern is if the process of 3D printing",
"unclear if UHMWPE is a sane choice, as it appears to be useful",
"kevlar, fibreglass, or carbon fiber), safe for implantation in the human body? Or",
"answers this unambiguously would be the ideal answer to this question. Another concern",
"printers can actually reliably print UHMWPE. Furthermore, it is unclear if UHMWPE is",
"based 3D printers in the sub $10,000 range (arbitrarily chosen to make the",
"issue of adverse host responses is more crucial, e.g. causing inflammation or it",
"for this question)? If not, why not? If most of them are safe,",
"3D printer) materials, such as ABS or PLA (or slightly more exotic ones,",
"available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use. This",
"This question is for materials intended to be implanted. Are any typical 3D",
"of them are safe, then please explain which ones are NOT safe. Highly",
"ABS or PLA (or slightly more exotic ones, such as kevlar, fibreglass, or",
"not? If most of them are safe, then please explain which ones are",
"have investigated what materials are safe for implantation in the human body? A",
"it. I can easily find that ABS plastic is \"non-biodegradable\", but I suppose",
"where strength is required, such as for joints. What about other applications where",
"issues as a result of the 3D printing process itself. However, it is",
"the material in the context of implantation applications. I've tried to determine the",
"for implantable electronics)? I'm aware that titanium appears to be frequently used for",
"3D printers in the sub $10,000 range (arbitrarily chosen to make the question",
"bearing properties are not required (e.g. a simple enclosure for implantable electronics)? I'm",
"in the human body? Or in medical terms, are they biocompatible (biofunctionality is",
"Or in medical terms, are they biocompatible (biofunctionality is not topical for this",
"printers do exist, they are beyond the scope of this question. The valid",
"general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But appears to be for non-implantation use. This question is for",
"silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I found a paper describing the",
"with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper dealing",
"relevant, and perhaps even more interesting is: Are there any peer reviewed medical",
"that have investigated what materials are safe for implantation in the human body?",
"appears to be for non-implantation use. This question is for materials intended to",
"which appears to be commonly used as implants: DOI: 10.1109/EEIC.2005.1566331 By extension, a",
"intended to be implanted. Are any typical 3D printed (extrusion based 3D printer)",
"it appears to be useful in applications where strength is required, such as",
"be safe, barring any adverse chemical or mechanical issues as a result of",
"answer it. I can easily find that ABS plastic is \"non-biodegradable\", but I",
"dealing with silicone-urethane being prone to breakdown: DOI: 10.1021/ma301965y I found a paper",
"extension, a 3D printer using UHMWPE might be safe, barring any adverse chemical",
"is unclear if UHMWPE is a sane choice, as it appears to be",
"for joints. What about other applications where load bearing properties are not required",
"properties and history of ultra-high molecular weight polyethylene (UHMWPE), which appears to be",
"medical papers that have investigated what materials are safe for implantation in the",
"applications where strength is required, such as for joints. What about other applications",
"answer to this question myself, but I cannot find any papers or studies",
"I suppose the issue of adverse host responses is more crucial, e.g. causing",
"sane choice, as it appears to be useful in applications where strength is",
"a bacterial growth substrate to promote infections seems like plausible concerns. I'm sure",
"not clear to me if any 3D printers can actually reliably print UHMWPE.",
"question is similar: [Are there biocompatible materials available to the general public?](https://3dprinting.stackexchange.com/questions/156/are-there-biocompatible-materials-available-to-the-general-public) But",
"of the material in the context of implantation applications. I've tried to determine",
"paper dealing with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found a",
"dealing with corrosion issues for implantable metals: DOI: 10.1089/end.1997.11.383 I found a paper",
"joints. What about other applications where load bearing properties are not required (e.g.",
"to be implanted. Are any typical 3D printed (extrusion based 3D printer) materials,",
"not topical for this question)? If not, why not? If most of them",
"I can easily find that ABS plastic is \"non-biodegradable\", but I suppose the",
"result of the 3D printing process itself. However, it is not clear to",
"if UHMWPE is a sane choice, as it appears to be useful in",
"the scope of this question. The valid context is extrusion based 3D printers",
"question)? If not, why not? If most of them are safe, then please",
"do exist, they are beyond the scope of this question. The valid context",
"is: Are there any peer reviewed medical papers that have investigated what materials",
"carbon fiber), safe for implantation in the human body? Or in medical terms,",
"molecular weight polyethylene (UHMWPE), which appears to be commonly used as implants: DOI:",
"the properties of the material in the context of implantation applications. I've tried",
"the human body? Or in medical terms, are they biocompatible (biofunctionality is not",
"this question. The valid context is extrusion based 3D printers in the sub",
"the issue of adverse host responses is more crucial, e.g. causing inflammation or",
"3D printing process itself. However, it is not clear to me if any",
"there might be other dangerous complications too, which I'm not aware of. I"
] |
[
"a clearance in the axial for moving up and down. When I put",
"is not the problem what is the problem in my situation?** I have",
"change? and if this is not the problem what is the problem in",
"for rapid movement and rapid changes in directions. I think the noise is",
"axial of the fan because I think there is a clearance in the",
"and down. When I put my finger on the fan body(the rotating part)",
"the noise stop! **My question, What type of fans suitable for rapid movement",
"noise is coming from the axial of the fan because I think there",
"direction change? and if this is not the problem what is the problem",
"think the noise is coming from the axial of the fan because I",
"type of fans is not suitable for rapid movement and rapid changes in",
"I think there is a clearance in the axial for moving up and",
"this is not the problem what is the problem in my situation?** I",
"think this type of fans is not suitable for rapid movement and rapid",
"is not suitable for rapid movement and rapid changes in directions. I think",
"situation?** I have tried searching but I can really find a direct answer!",
"number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When",
"moving up and down. When I put my finger on the fan body(the",
"is the problem in my situation?** I have tried searching but I can",
"for rapid movement and rapid direction change? and if this is not the",
"I think the noise is coming from the axial of the fan because",
"I put my finger on the fan body(the rotating part) the noise stop!",
"and rapid changes in directions. I think the noise is coming from the",
"**My question, What type of fans suitable for rapid movement and rapid direction",
"the X-axis it makes noise. I think this type of fans is not",
"because I think there is a clearance in the axial for moving up",
"of fans is not suitable for rapid movement and rapid changes in directions.",
"rapid direction change? and if this is not the problem what is the",
"in the X-axis it makes noise. I think this type of fans is",
"in directions. I think the noise is coming from the axial of the",
"[fan model](https://www.tme.eu/en/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/), it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a",
"What type of fans suitable for rapid movement and rapid direction change? and",
"a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the X-axis",
"directions. I think the noise is coming from the axial of the fan",
"model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg)",
"what is the problem in my situation?** I have tried searching but I",
"description here](https://i.stack.imgur.com/rGueR.jpg)](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the X-axis it makes noise.",
"model](https://www.tme.eu/en/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/), it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower",
"the head is moving in the X-axis it makes noise. I think this",
"part) the noise stop! **My question, What type of fans suitable for rapid",
"on the fan body(the rotating part) the noise stop! **My question, What type",
"makes noise. I think this type of fans is not suitable for rapid",
"is coming from the axial of the fan because I think there is",
"rotating part) the noise stop! **My question, What type of fans suitable for",
"the axial of the fan because I think there is a clearance in",
"rapid changes in directions. I think the noise is coming from the axial",
"the fan because I think there is a clearance in the axial for",
"movement and rapid changes in directions. I think the noise is coming from",
"in the axial for moving up and down. When I put my finger",
"of the fan because I think there is a clearance in the axial",
"[](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the X-axis it",
"not suitable for rapid movement and rapid changes in directions. I think the",
"fan because I think there is a clearance in the axial for moving",
"down. When I put my finger on the fan body(the rotating part) the",
"noise. I think this type of fans is not suitable for rapid movement",
"the fan body(the rotating part) the noise stop! **My question, What type of",
"body(the rotating part) the noise stop! **My question, What type of fans suitable",
"finger on the fan body(the rotating part) the noise stop! **My question, What",
"stop! **My question, What type of fans suitable for rapid movement and rapid",
"problem what is the problem in my situation?** I have tried searching but",
"and rapid direction change? and if this is not the problem what is",
"changes in directions. I think the noise is coming from the axial of",
"is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head is moving",
"movement and rapid direction change? and if this is not the problem what",
"I have this [fan model](https://www.tme.eu/en/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/), it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and",
"the axial for moving up and down. When I put my finger on",
"if this is not the problem what is the problem in my situation?**",
"the problem in my situation?** I have tried searching but I can really",
"SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the",
"fan body(the rotating part) the noise stop! **My question, What type of fans",
"it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head is",
"and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head",
"coming from the axial of the fan because I think there is a",
"question, What type of fans suitable for rapid movement and rapid direction change?",
"[MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the",
"of fans suitable for rapid movement and rapid direction change? and if this",
"it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type.",
"suitable for rapid movement and rapid changes in directions. I think the noise",
"fans is not suitable for rapid movement and rapid changes in directions. I",
"clearance in the axial for moving up and down. When I put my",
"the noise is coming from the axial of the fan because I think",
"I think this type of fans is not suitable for rapid movement and",
"When I put my finger on the fan body(the rotating part) the noise",
"not the problem what is the problem in my situation?** I have tried",
"put my finger on the fan body(the rotating part) the noise stop! **My",
"have this [fan model](https://www.tme.eu/en/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/), it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it",
"moving in the X-axis it makes noise. I think this type of fans",
"my finger on the fan body(the rotating part) the noise stop! **My question,",
"problem in my situation?** I have tried searching but I can really find",
"the problem what is the problem in my situation?** I have tried searching",
"a blower type. [](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in",
"rapid movement and rapid direction change? and if this is not the problem",
"image description here](https://i.stack.imgur.com/rGueR.jpg)](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the X-axis it makes",
"it makes noise. I think this type of fans is not suitable for",
"for moving up and down. When I put my finger on the fan",
"this type of fans is not suitable for rapid movement and rapid changes",
"noise stop! **My question, What type of fans suitable for rapid movement and",
"head is moving in the X-axis it makes noise. I think this type",
"axial for moving up and down. When I put my finger on the",
"is a clearance in the axial for moving up and down. When I",
"in my situation?** I have tried searching but I can really find a",
"this [fan model](https://www.tme.eu/en/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/), it is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is",
"fans suitable for rapid movement and rapid direction change? and if this is",
"here](https://i.stack.imgur.com/rGueR.jpg)](https://i.stack.imgur.com/rGueR.jpg) When the head is moving in the X-axis it makes noise. I",
"type of fans suitable for rapid movement and rapid direction change? and if",
"rapid movement and rapid changes in directions. I think the noise is coming",
"from the axial of the fan because I think there is a clearance",
"is a SUNON model number [MF50151VX-B00U-A99](https://www.tme.eu/en/Document/b30ea71fee61d11101012e50df6ac0ad/MF50151VX-A99-DTE.pdf) and it is a blower type. [![enter"
] |
[
"the temp jumped to 260 °C. I shut down the printer at that",
"heating up erratically. I first noticed this while printing a part in PETG",
"PETG and the temp jumped to 260 °C. I shut down the printer",
"up erratically. I first noticed this while printing a part in PETG and",
"was heating up erratically. I first noticed this while printing a part in",
"to 260 °C. I shut down the printer at that time and first",
"tightened too much. I disassembled the entire hotend, cleaned everything and then reassembled",
"had the screw on glass thermistor. Again the same erratic behavior and unreal",
"the hardware. I noticed that the E3D V6 thermistor had been tightened too",
"readings. What could be wrong here? What am I missing? Can this be",
"the E3D V6 thermistor had been tightened too much. I disassembled the entire",
"the strange behavior occurs. The hotend steadily climbed up till about 200 °C.",
"I thought the MEGA might be at fault. I replaced it and the",
"clone). This had the screw on glass thermistor. Again the same erratic behavior",
"the same erratic behavior and unreal temp readings. What could be wrong here?",
"fault. I replaced it and the hotend (an E3D V6 clone). This had",
"hardware. I noticed that the E3D V6 thermistor had been tightened too much.",
"the screw on glass thermistor. Again the same erratic behavior and unreal temp",
"been tightened too much. I disassembled the entire hotend, cleaned everything and then",
"down the printer at that time and first started checking the hardware. I",
"and the hotend (an E3D V6 clone). This had the screw on glass",
"everything and then reassembled everything. I thought to retune the hotend and when",
"then reassembled everything. I thought to retune the hotend and when I tried",
"I tried tuning it at 240 °C. This is where the strange behavior",
"printer at that time and first started checking the hardware. I noticed that",
"temp readings. What could be wrong here? What am I missing? Can this",
"shut down the printer at that time and first started checking the hardware.",
"hotend steadily climbed up till about 200 °C. After that it just went",
"that my hotend was heating up erratically. I first noticed this while printing",
"E3D V6 clone). This had the screw on glass thermistor. Again the same",
"260 °C. I shut down the printer at that time and first started",
"two days ago, I started seeing that my hotend was heating up erratically.",
"°C. I shut down the printer at that time and first started checking",
"this point I thought the MEGA might be at fault. I replaced it",
"noticed this while printing a part in PETG and the temp jumped to",
"on glass thermistor. Again the same erratic behavior and unreal temp readings. What",
"to retune the hotend and when I tried tuning it at 240 °C.",
"might be at fault. I replaced it and the hotend (an E3D V6",
"and then reassembled everything. I thought to retune the hotend and when I",
"°C. This is where the strange behavior occurs. The hotend steadily climbed up",
"such as 646 °C and such. At this point I thought the MEGA",
"same erratic behavior and unreal temp readings. What could be wrong here? What",
"the hotend and when I tried tuning it at 240 °C. This is",
"tried tuning it at 240 °C. This is where the strange behavior occurs.",
"the hotend (an E3D V6 clone). This had the screw on glass thermistor.",
"that time and first started checking the hardware. I noticed that the E3D",
"the entire hotend, cleaned everything and then reassembled everything. I thought to retune",
"I noticed that the E3D V6 thermistor had been tightened too much. I",
"went nuts. I started seeing unreal temps such as 646 °C and such.",
"could be wrong here? What am I missing? Can this be the heater",
"about 200 °C. After that it just went nuts. I started seeing unreal",
"(an E3D V6 clone). This had the screw on glass thermistor. Again the",
"printing a part in PETG and the temp jumped to 260 °C. I",
"when I tried tuning it at 240 °C. This is where the strange",
"and the temp jumped to 260 °C. I shut down the printer at",
"thought the MEGA might be at fault. I replaced it and the hotend",
"erratically. I first noticed this while printing a part in PETG and the",
"my hotend was heating up erratically. I first noticed this while printing a",
"MEGA might be at fault. I replaced it and the hotend (an E3D",
"till about 200 °C. After that it just went nuts. I started seeing",
"The hotend steadily climbed up till about 200 °C. After that it just",
"point I thought the MEGA might be at fault. I replaced it and",
"had been tightened too much. I disassembled the entire hotend, cleaned everything and",
"where the strange behavior occurs. The hotend steadily climbed up till about 200",
"What could be wrong here? What am I missing? Can this be the",
"Again the same erratic behavior and unreal temp readings. What could be wrong",
"is where the strange behavior occurs. The hotend steadily climbed up till about",
"screw on glass thermistor. Again the same erratic behavior and unreal temp readings.",
"hotend, cleaned everything and then reassembled everything. I thought to retune the hotend",
"jumped to 260 °C. I shut down the printer at that time and",
"everything. I thought to retune the hotend and when I tried tuning it",
"V6 thermistor had been tightened too much. I disassembled the entire hotend, cleaned",
"steadily climbed up till about 200 °C. After that it just went nuts.",
"200 °C. After that it just went nuts. I started seeing unreal temps",
"behavior and unreal temp readings. What could be wrong here? What am I",
"646 °C and such. At this point I thought the MEGA might be",
"as 646 °C and such. At this point I thought the MEGA might",
"up till about 200 °C. After that it just went nuts. I started",
"at fault. I replaced it and the hotend (an E3D V6 clone). This",
"climbed up till about 200 °C. After that it just went nuts. I",
"hotend (an E3D V6 clone). This had the screw on glass thermistor. Again",
"the printer at that time and first started checking the hardware. I noticed",
"while printing a part in PETG and the temp jumped to 260 °C.",
"started checking the hardware. I noticed that the E3D V6 thermistor had been",
"hotend was heating up erratically. I first noticed this while printing a part",
"entire hotend, cleaned everything and then reassembled everything. I thought to retune the",
"at 240 °C. This is where the strange behavior occurs. The hotend steadily",
"seeing unreal temps such as 646 °C and such. At this point I",
"be at fault. I replaced it and the hotend (an E3D V6 clone).",
"°C. After that it just went nuts. I started seeing unreal temps such",
"much. I disassembled the entire hotend, cleaned everything and then reassembled everything. I",
"reassembled everything. I thought to retune the hotend and when I tried tuning",
"just went nuts. I started seeing unreal temps such as 646 °C and",
"glass thermistor. Again the same erratic behavior and unreal temp readings. What could",
"V6 clone). This had the screw on glass thermistor. Again the same erratic",
"behavior occurs. The hotend steadily climbed up till about 200 °C. After that",
"started seeing unreal temps such as 646 °C and such. At this point",
"be wrong here? What am I missing? Can this be the heater cartridge?",
"disassembled the entire hotend, cleaned everything and then reassembled everything. I thought to",
"days ago, I started seeing that my hotend was heating up erratically. I",
"E3D V6 thermistor had been tightened too much. I disassembled the entire hotend,",
"I thought to retune the hotend and when I tried tuning it at",
"and first started checking the hardware. I noticed that the E3D V6 thermistor",
"it just went nuts. I started seeing unreal temps such as 646 °C",
"unreal temps such as 646 °C and such. At this point I thought",
"hotend and when I tried tuning it at 240 °C. This is where",
"noticed that the E3D V6 thermistor had been tightened too much. I disassembled",
"240 °C. This is where the strange behavior occurs. The hotend steadily climbed",
"and when I tried tuning it at 240 °C. This is where the",
"nuts. I started seeing unreal temps such as 646 °C and such. At",
"seeing that my hotend was heating up erratically. I first noticed this while",
"I replaced it and the hotend (an E3D V6 clone). This had the",
"°C and such. At this point I thought the MEGA might be at",
"thermistor had been tightened too much. I disassembled the entire hotend, cleaned everything",
"it and the hotend (an E3D V6 clone). This had the screw on",
"part in PETG and the temp jumped to 260 °C. I shut down",
"time and first started checking the hardware. I noticed that the E3D V6",
"strange behavior occurs. The hotend steadily climbed up till about 200 °C. After",
"After that it just went nuts. I started seeing unreal temps such as",
"and unreal temp readings. What could be wrong here? What am I missing?",
"it at 240 °C. This is where the strange behavior occurs. The hotend",
"temps such as 646 °C and such. At this point I thought the",
"and such. At this point I thought the MEGA might be at fault.",
"first started checking the hardware. I noticed that the E3D V6 thermistor had",
"erratic behavior and unreal temp readings. What could be wrong here? What am",
"cleaned everything and then reassembled everything. I thought to retune the hotend and",
"I disassembled the entire hotend, cleaned everything and then reassembled everything. I thought",
"unreal temp readings. What could be wrong here? What am I missing? Can",
"This is where the strange behavior occurs. The hotend steadily climbed up till",
"thought to retune the hotend and when I tried tuning it at 240",
"ago, I started seeing that my hotend was heating up erratically. I first",
"About two days ago, I started seeing that my hotend was heating up",
"This had the screw on glass thermistor. Again the same erratic behavior and",
"first noticed this while printing a part in PETG and the temp jumped",
"that it just went nuts. I started seeing unreal temps such as 646",
"too much. I disassembled the entire hotend, cleaned everything and then reassembled everything.",
"this while printing a part in PETG and the temp jumped to 260",
"in PETG and the temp jumped to 260 °C. I shut down the",
"I first noticed this while printing a part in PETG and the temp",
"I started seeing unreal temps such as 646 °C and such. At this",
"temp jumped to 260 °C. I shut down the printer at that time",
"at that time and first started checking the hardware. I noticed that the",
"thermistor. Again the same erratic behavior and unreal temp readings. What could be",
"such. At this point I thought the MEGA might be at fault. I",
"checking the hardware. I noticed that the E3D V6 thermistor had been tightened",
"tuning it at 240 °C. This is where the strange behavior occurs. The",
"started seeing that my hotend was heating up erratically. I first noticed this",
"retune the hotend and when I tried tuning it at 240 °C. This",
"a part in PETG and the temp jumped to 260 °C. I shut",
"At this point I thought the MEGA might be at fault. I replaced",
"the MEGA might be at fault. I replaced it and the hotend (an",
"that the E3D V6 thermistor had been tightened too much. I disassembled the",
"occurs. The hotend steadily climbed up till about 200 °C. After that it",
"I started seeing that my hotend was heating up erratically. I first noticed",
"replaced it and the hotend (an E3D V6 clone). This had the screw",
"I shut down the printer at that time and first started checking the"
] |
[
"dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS 1.4 or 1.5 or 1.6.",
"about to build a [Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use",
"be advisable to upgrade a RAMPS 1.4 board (replacing the MOSFETs, connectors, and",
"to build a [Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS",
"1.6. What is the big difference? Is it only the MOSFETs and the",
"What is the big difference? Is it only the MOSFETs and the poly-fuses?",
"use RAMPS 1.4 or 1.5 or 1.6. What is the big difference? Is",
"If that is the case, would it be advisable to upgrade a RAMPS",
"I'm about to build a [Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to",
"it be advisable to upgrade a RAMPS 1.4 board (replacing the MOSFETs, connectors,",
"that is the case, would it be advisable to upgrade a RAMPS 1.4",
"is the case, would it be advisable to upgrade a RAMPS 1.4 board",
"only the MOSFETs and the poly-fuses? If that is the case, would it",
"to use RAMPS 1.4 or 1.5 or 1.6. What is the big difference?",
"1.5 or 1.6. What is the big difference? Is it only the MOSFETs",
"am confused whether to use RAMPS 1.4 or 1.5 or 1.6. What is",
"it only the MOSFETs and the poly-fuses? If that is the case, would",
"would it be advisable to upgrade a RAMPS 1.4 board (replacing the MOSFETs,",
"is the big difference? Is it only the MOSFETs and the poly-fuses? If",
"MOSFETs and the poly-fuses? If that is the case, would it be advisable",
"the big difference? Is it only the MOSFETs and the poly-fuses? If that",
"big difference? Is it only the MOSFETs and the poly-fuses? If that is",
"or 1.6. What is the big difference? Is it only the MOSFETs and",
"advisable to upgrade a RAMPS 1.4 board (replacing the MOSFETs, connectors, and fuses)?",
"Is it only the MOSFETs and the poly-fuses? If that is the case,",
"whether to use RAMPS 1.4 or 1.5 or 1.6. What is the big",
"1.4 or 1.5 or 1.6. What is the big difference? Is it only",
"a [Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS 1.4 or",
"difference? Is it only the MOSFETs and the poly-fuses? If that is the",
"and the poly-fuses? If that is the case, would it be advisable to",
"RAMPS 1.4 or 1.5 or 1.6. What is the big difference? Is it",
"i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS 1.4 or 1.5 or",
"or 1.5 or 1.6. What is the big difference? Is it only the",
"the MOSFETs and the poly-fuses? If that is the case, would it be",
"case, would it be advisable to upgrade a RAMPS 1.4 board (replacing the",
"build a [Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS 1.4",
"the poly-fuses? If that is the case, would it be advisable to upgrade",
"[Prusa i3 dolly](https://toms3d.org/2017/02/23/building-cheapest-possible-prusa-i3-mk2/). I am confused whether to use RAMPS 1.4 or 1.5",
"confused whether to use RAMPS 1.4 or 1.5 or 1.6. What is the",
"poly-fuses? If that is the case, would it be advisable to upgrade a",
"the case, would it be advisable to upgrade a RAMPS 1.4 board (replacing",
"I am confused whether to use RAMPS 1.4 or 1.5 or 1.6. What"
] |
[
"height? I found that some printers can do .05 layer heights, but the",
"printers can do .05 layer heights, but the Anet A6 can't? I am",
"do .05 layer heights, but the Anet A6 can't? I am interested to",
"A6 can't? I am interested to know if it is the stepper motors",
"the title, Why can't the Anet A6 do .05 layer height? I found",
"do .05 layer height? I found that some printers can do .05 layer",
"that some printers can do .05 layer heights, but the Anet A6 can't?",
"heights, but the Anet A6 can't? I am interested to know if it",
"I am interested to know if it is the stepper motors or the",
"is the stepper motors or the threaded rods or something. Maybe this is",
"Anet A6 do .05 layer height? I found that some printers can do",
"am interested to know if it is the stepper motors or the threaded",
"Why can't the Anet A6 do .05 layer height? I found that some",
"the Anet A6 do .05 layer height? I found that some printers can",
"or the threaded rods or something. Maybe this is something I can do",
"found that some printers can do .05 layer heights, but the Anet A6",
"if it is the stepper motors or the threaded rods or something. Maybe",
"it is the stepper motors or the threaded rods or something. Maybe this",
"layer height? I found that some printers can do .05 layer heights, but",
"can't? I am interested to know if it is the stepper motors or",
"I found that some printers can do .05 layer heights, but the Anet",
"sayed in the title, Why can't the Anet A6 do .05 layer height?",
"Anet A6 can't? I am interested to know if it is the stepper",
"the threaded rods or something. Maybe this is something I can do a",
"or something. Maybe this is something I can do a small \"test print\"",
"stepper motors or the threaded rods or something. Maybe this is something I",
"layer heights, but the Anet A6 can't? I am interested to know if",
"A6 do .05 layer height? I found that some printers can do .05",
"can't the Anet A6 do .05 layer height? I found that some printers",
"So like I sayed in the title, Why can't the Anet A6 do",
"threaded rods or something. Maybe this is something I can do a small",
".05 layer heights, but the Anet A6 can't? I am interested to know",
"to know if it is the stepper motors or the threaded rods or",
"something. Maybe this is something I can do a small \"test print\" on?",
"interested to know if it is the stepper motors or the threaded rods",
"like I sayed in the title, Why can't the Anet A6 do .05",
"I sayed in the title, Why can't the Anet A6 do .05 layer",
"title, Why can't the Anet A6 do .05 layer height? I found that",
"know if it is the stepper motors or the threaded rods or something.",
"the Anet A6 can't? I am interested to know if it is the",
"can do .05 layer heights, but the Anet A6 can't? I am interested",
"motors or the threaded rods or something. Maybe this is something I can",
"the stepper motors or the threaded rods or something. Maybe this is something",
"some printers can do .05 layer heights, but the Anet A6 can't? I",
".05 layer height? I found that some printers can do .05 layer heights,",
"rods or something. Maybe this is something I can do a small \"test",
"in the title, Why can't the Anet A6 do .05 layer height? I",
"but the Anet A6 can't? I am interested to know if it is"
] |
[
"colour material but when I pressed \"load filament\", it didn't make anything. Often",
"push it into the extruder and the remains of the old filament do",
"that the printer works. I don't have any pictures but the filament is",
"filament\", it didn't make anything. Often after five times doing that the printer",
"and we've changed for a print with another colour material but when I",
"and the printer holds it. However, it doesn't push it into the extruder",
"filament do not come out, so I wonder why the motors just stop",
"for a print with another colour material but when I pressed \"load filament\",",
"pressed \"load filament\", it didn't make anything. Often after five times doing that",
"Prusa i3 MK2 and we've changed for a print with another colour material",
"any pictures but the filament is in the hole and the printer holds",
"I wonder why the motors just stop and don't work. Sometimes there are",
"not come out, so I wonder why the motors just stop and don't",
"there are no problems - sometimes more and sometimes less. I hope someone",
"just stop and don't work. Sometimes there are no problems - sometimes more",
"changed for a print with another colour material but when I pressed \"load",
"times doing that the printer works. I don't have any pictures but the",
"it doesn't push it into the extruder and the remains of the old",
"with another colour material but when I pressed \"load filament\", it didn't make",
"more and sometimes less. I hope someone has the reason for this problem.",
"a Prusa i3 MK2 and we've changed for a print with another colour",
"pictures but the filament is in the hole and the printer holds it.",
"- sometimes more and sometimes less. I hope someone has the reason for",
"no problems - sometimes more and sometimes less. I hope someone has the",
"and the remains of the old filament do not come out, so I",
"works. I don't have any pictures but the filament is in the hole",
"anything. Often after five times doing that the printer works. I don't have",
"material but when I pressed \"load filament\", it didn't make anything. Often after",
"problems - sometimes more and sometimes less. I hope someone has the reason",
"printer works. I don't have any pictures but the filament is in the",
"holds it. However, it doesn't push it into the extruder and the remains",
"it into the extruder and the remains of the old filament do not",
"\"load filament\", it didn't make anything. Often after five times doing that the",
"i3 MK2 and we've changed for a print with another colour material but",
"don't have any pictures but the filament is in the hole and the",
"old filament do not come out, so I wonder why the motors just",
"the remains of the old filament do not come out, so I wonder",
"motors just stop and don't work. Sometimes there are no problems - sometimes",
"the old filament do not come out, so I wonder why the motors",
"Sometimes there are no problems - sometimes more and sometimes less. I hope",
"another colour material but when I pressed \"load filament\", it didn't make anything.",
"it didn't make anything. Often after five times doing that the printer works.",
"remains of the old filament do not come out, so I wonder why",
"out, so I wonder why the motors just stop and don't work. Sometimes",
"and don't work. Sometimes there are no problems - sometimes more and sometimes",
"work. Sometimes there are no problems - sometimes more and sometimes less. I",
"do not come out, so I wonder why the motors just stop and",
"into the extruder and the remains of the old filament do not come",
"we've changed for a print with another colour material but when I pressed",
"filament is in the hole and the printer holds it. However, it doesn't",
"print with another colour material but when I pressed \"load filament\", it didn't",
"the hole and the printer holds it. However, it doesn't push it into",
"We have a Prusa i3 MK2 and we've changed for a print with",
"five times doing that the printer works. I don't have any pictures but",
"have any pictures but the filament is in the hole and the printer",
"the motors just stop and don't work. Sometimes there are no problems -",
"stop and don't work. Sometimes there are no problems - sometimes more and",
"Often after five times doing that the printer works. I don't have any",
"are no problems - sometimes more and sometimes less. I hope someone has",
"doing that the printer works. I don't have any pictures but the filament",
"the printer holds it. However, it doesn't push it into the extruder and",
"why the motors just stop and don't work. Sometimes there are no problems",
"make anything. Often after five times doing that the printer works. I don't",
"have a Prusa i3 MK2 and we've changed for a print with another",
"come out, so I wonder why the motors just stop and don't work.",
"don't work. Sometimes there are no problems - sometimes more and sometimes less.",
"the filament is in the hole and the printer holds it. However, it",
"printer holds it. However, it doesn't push it into the extruder and the",
"hole and the printer holds it. However, it doesn't push it into the",
"MK2 and we've changed for a print with another colour material but when",
"extruder and the remains of the old filament do not come out, so",
"of the old filament do not come out, so I wonder why the",
"the extruder and the remains of the old filament do not come out,",
"I don't have any pictures but the filament is in the hole and",
"sometimes more and sometimes less. I hope someone has the reason for this",
"it. However, it doesn't push it into the extruder and the remains of",
"the printer works. I don't have any pictures but the filament is in",
"in the hole and the printer holds it. However, it doesn't push it",
"didn't make anything. Often after five times doing that the printer works. I",
"but the filament is in the hole and the printer holds it. However,",
"when I pressed \"load filament\", it didn't make anything. Often after five times",
"but when I pressed \"load filament\", it didn't make anything. Often after five",
"is in the hole and the printer holds it. However, it doesn't push",
"I pressed \"load filament\", it didn't make anything. Often after five times doing",
"so I wonder why the motors just stop and don't work. Sometimes there",
"a print with another colour material but when I pressed \"load filament\", it",
"doesn't push it into the extruder and the remains of the old filament",
"However, it doesn't push it into the extruder and the remains of the",
"wonder why the motors just stop and don't work. Sometimes there are no",
"after five times doing that the printer works. I don't have any pictures"
] |
[
"screw isn't tapped. Does anyone know the thread size, w.r.t. both pitch and",
"left nut for the lead screw isn't tapped. Does anyone know the thread",
"and unfortunately the left nut for the lead screw isn't tapped. Does anyone",
"lead screw isn't tapped. Does anyone know the thread size, w.r.t. both pitch",
"Does anyone know the thread size, w.r.t. both pitch and lead, of the",
"printer, and unfortunately the left nut for the lead screw isn't tapped. Does",
"nut for the lead screw isn't tapped. Does anyone know the thread size,",
"new printer, and unfortunately the left nut for the lead screw isn't tapped.",
"I bought a new printer, and unfortunately the left nut for the lead",
"for the lead screw isn't tapped. Does anyone know the thread size, w.r.t.",
"know the thread size, w.r.t. both pitch and lead, of the lead screws?",
"anyone know the thread size, w.r.t. both pitch and lead, of the lead",
"unfortunately the left nut for the lead screw isn't tapped. Does anyone know",
"a new printer, and unfortunately the left nut for the lead screw isn't",
"the lead screw isn't tapped. Does anyone know the thread size, w.r.t. both",
"bought a new printer, and unfortunately the left nut for the lead screw",
"isn't tapped. Does anyone know the thread size, w.r.t. both pitch and lead,",
"tapped. Does anyone know the thread size, w.r.t. both pitch and lead, of",
"the left nut for the lead screw isn't tapped. Does anyone know the"
] |
[
"XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder",
"have tried decreasing speed to 40 mm/s but the issue remains. **Printer**: Geetech",
"Geetech Prusa I3 Pro B XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s",
"[](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40 mm/s but the issue",
"I am attempting to print the Benchy boat but every attempt so far",
"20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50",
"already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40 mm/s",
"Pro B XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000",
"of slope/blob on the nose of the boat, which emerges after the first",
"after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of",
"on the nose of the boat, which emerges after the first 30 layers.",
"mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s Travel Speed: 120 mm/s",
"2](https://i.stack.imgur.com/q9Z6A.jpg)](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40 mm/s but the issue remains.",
"Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed:",
"boat but every attempt so far has been unsuccessful. The print has a",
"slope/blob on the nose of the boat, which emerges after the first 30",
"40 mm/s but the issue remains. **Printer**: Geetech Prusa I3 Pro B XY",
"front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing",
"has a sort of slope/blob on the nose of the boat, which emerges",
"Jerk: 5 mm/s Printing Speed: 50 mm/s Travel Speed: 120 mm/s Layer Height:",
"mm/s Printing Speed: 50 mm/s Travel Speed: 120 mm/s Layer Height: 0.1 mm",
"mm/s but the issue remains. **Printer**: Geetech Prusa I3 Pro B XY Accelleration:",
"of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed",
"**Printer**: Geetech Prusa I3 Pro B XY Accelleration: 1000 mm/s2 XY Jerk: 20",
"Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s Travel",
"but the issue remains. **Printer**: Geetech Prusa I3 Pro B XY Accelleration: 1000",
"Height: 0.1 mm Infill: 60% (Lines) Material: PLA, 200 °C, 1.75mm filament, retraction",
"the boat, which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can",
"far has been unsuccessful. The print has a sort of slope/blob on the",
"which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the",
"first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of the boat",
"attempting to print the Benchy boat but every attempt so far has been",
"sort of slope/blob on the nose of the boat, which emerges after the",
"Prusa I3 Pro B XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction",
"50 mm/s Travel Speed: 120 mm/s Layer Height: 0.1 mm Infill: 60% (Lines)",
"the nose of the boat, which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg)",
"every attempt so far has been unsuccessful. The print has a sort of",
"I3 Pro B XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration:",
"the front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried",
"decreasing speed to 40 mm/s but the issue remains. **Printer**: Geetech Prusa I3",
"arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40 mm/s but",
"remains. **Printer**: Geetech Prusa I3 Pro B XY Accelleration: 1000 mm/s2 XY Jerk:",
"attempt so far has been unsuccessful. The print has a sort of slope/blob",
"The print has a sort of slope/blob on the nose of the boat,",
"speed to 40 mm/s but the issue remains. **Printer**: Geetech Prusa I3 Pro",
"a sort of slope/blob on the nose of the boat, which emerges after",
"mm/s Travel Speed: 120 mm/s Layer Height: 0.1 mm Infill: 60% (Lines) Material:",
"tried decreasing speed to 40 mm/s but the issue remains. **Printer**: Geetech Prusa",
"120 mm/s Layer Height: 0.1 mm Infill: 60% (Lines) Material: PLA, 200 °C,",
"has been unsuccessful. The print has a sort of slope/blob on the nose",
"unsuccessful. The print has a sort of slope/blob on the nose of the",
"layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of the boat already arching",
"the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to",
"0.1 mm Infill: 60% (Lines) Material: PLA, 200 °C, 1.75mm filament, retraction enabled.",
"Speed: 120 mm/s Layer Height: 0.1 mm Infill: 60% (Lines) Material: PLA, 200",
"Speed: 50 mm/s Travel Speed: 120 mm/s Layer Height: 0.1 mm Infill: 60%",
"Benchy boat but every attempt so far has been unsuccessful. The print has",
"boat, which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see",
"can see the front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I",
"the issue remains. **Printer**: Geetech Prusa I3 Pro B XY Accelleration: 1000 mm/s2",
"mm/s Layer Height: 0.1 mm Infill: 60% (Lines) Material: PLA, 200 °C, 1.75mm",
"boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40",
"but every attempt so far has been unsuccessful. The print has a sort",
"of the boat, which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you",
"the Benchy boat but every attempt so far has been unsuccessful. The print",
"emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front",
"30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of the boat already",
"you can see the front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg)",
"mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s",
"1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5",
"see the front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have",
"Travel Speed: 120 mm/s Layer Height: 0.1 mm Infill: 60% (Lines) Material: PLA,",
"print has a sort of slope/blob on the nose of the boat, which",
"the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of the",
"Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s Travel Speed: 120 mm/s Layer",
"5 mm/s Printing Speed: 50 mm/s Travel Speed: 120 mm/s Layer Height: 0.1",
"am attempting to print the Benchy boat but every attempt so far has",
"Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s Travel Speed:",
"so far has been unsuccessful. The print has a sort of slope/blob on",
"been unsuccessful. The print has a sort of slope/blob on the nose of",
"I have tried decreasing speed to 40 mm/s but the issue remains. **Printer**:",
"Layer Height: 0.1 mm Infill: 60% (Lines) Material: PLA, 200 °C, 1.75mm filament,",
"B XY Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2",
"2000 mm/s2 Extruder Jerk: 5 mm/s Printing Speed: 50 mm/s Travel Speed: 120",
"Accelleration: 1000 mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk:",
"issue remains. **Printer**: Geetech Prusa I3 Pro B XY Accelleration: 1000 mm/s2 XY",
"Here you can see the front of the boat already arching up: [](https://i.stack.imgur.com/q9Z6A.jpg) I have tried decreasing speed to 40 mm/s but the",
"XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s Printing",
"mm/s2 XY Jerk: 20 mm/s Retraction Accelleration: 2000 mm/s2 Extruder Jerk: 5 mm/s",
"[](https://i.stack.imgur.com/vx2cM.jpg) Here you can see the front of the boat already arching up:",
"to print the Benchy boat but every attempt so far has been unsuccessful.",
"print the Benchy boat but every attempt so far has been unsuccessful. The",
"Printing Speed: 50 mm/s Travel Speed: 120 mm/s Layer Height: 0.1 mm Infill:",
"nose of the boat, which emerges after the first 30 layers. [](https://i.stack.imgur.com/vx2cM.jpg) Here"
] |
[
"For the hotend, I've bought the Greetech MK8 extruder. However, the temperature sensor",
"on the list for both Marlin and Repetier and the temp sensor reads",
"tried to select one of the NTC options on the list for both",
"it broken or am I selecting the wrong thermistor type? [Documentation for MK8](http://www.geeetech.com/assembled-mk8-extruder-p-857.html)",
"a steady 500 degrees Celsius. In Marlin, it shows it right up (I'm",
"to heat up, when it shoots to 500°C just like before with Marlin.",
"and Repetier and the temp sensor reads steady 3.600°C!!! Measuring it with the",
"the printer to heat up, when it shoots to 500°C just like before",
"wall. I've already checked the wires and connections, but the darn thing keeps",
"it shows 0.00°C, until I tell the printer to heat up, when it",
"until I tell the printer to heat up, when it shoots to 500°C",
"degrees Celsius. In Marlin, it shows it right up (I'm using the 1st",
"Prusa i3 MK2). For the hotend, I've bought the Greetech MK8 extruder. However,",
"from mixed parts (a MDF clone of Prusa i3 MK2). For the hotend,",
"Marlin. The documentation for this extruder only lists it as a \"100K NTC",
"up the wall. I've already checked the wires and connections, but the darn",
"as a \"100K NTC Thermistor\", so I tried to select one of the",
"the darn thing keeps showing a steady 500 degrees Celsius. In Marlin, it",
"the hotend, I've bought the Greetech MK8 extruder. However, the temperature sensor is",
"one), it shows 0.00°C, until I tell the printer to heat up, when",
"60k, it's 31°C outside. Is it broken or am I selecting the wrong",
"same one), it shows 0.00°C, until I tell the printer to heat up,",
"a Graber i3 printer from mixed parts (a MDF clone of Prusa i3",
"printer to heat up, when it shoots to 500°C just like before with",
"up, when it shoots to 500°C just like before with Marlin. The documentation",
"the Greetech MK8 extruder. However, the temperature sensor is driving me up the",
"before with Marlin. The documentation for this extruder only lists it as a",
"driving me up the wall. I've already checked the wires and connections, but",
"finish building a Graber i3 printer from mixed parts (a MDF clone of",
"options on the list for both Marlin and Repetier and the temp sensor",
"shows 0.00°C, until I tell the printer to heat up, when it shoots",
"I've already checked the wires and connections, but the darn thing keeps showing",
"Measuring it with the multimeter, it shows around 60k, it's 31°C outside. Is",
"500 degrees Celsius. In Marlin, it shows it right up (I'm using the",
"and the temp sensor reads steady 3.600°C!!! Measuring it with the multimeter, it",
"but the darn thing keeps showing a steady 500 degrees Celsius. In Marlin,",
"parts (a MDF clone of Prusa i3 MK2). For the hotend, I've bought",
"outside. Is it broken or am I selecting the wrong thermistor type? [Documentation",
"However, the temperature sensor is driving me up the wall. I've already checked",
"31°C outside. Is it broken or am I selecting the wrong thermistor type?",
"extruder only lists it as a \"100K NTC Thermistor\", so I tried to",
"Greetech MK8 extruder. However, the temperature sensor is driving me up the wall.",
"darn thing keeps showing a steady 500 degrees Celsius. In Marlin, it shows",
"The documentation for this extruder only lists it as a \"100K NTC Thermistor\",",
"NTC Thermistor\", so I tried to select one of the NTC options on",
"\"100K NTC Thermistor\", so I tried to select one of the NTC options",
"(I'm using the 1st option for a 100k thermistor), in Repetier Firmware (using",
"and connections, but the darn thing keeps showing a steady 500 degrees Celsius.",
"it's 31°C outside. Is it broken or am I selecting the wrong thermistor",
"like before with Marlin. The documentation for this extruder only lists it as",
"for this extruder only lists it as a \"100K NTC Thermistor\", so I",
"showing a steady 500 degrees Celsius. In Marlin, it shows it right up",
"Is it broken or am I selecting the wrong thermistor type? [Documentation for",
"using the 1st option for a 100k thermistor), in Repetier Firmware (using the",
"i3 printer from mixed parts (a MDF clone of Prusa i3 MK2). For",
"mixed parts (a MDF clone of Prusa i3 MK2). For the hotend, I've",
"I tried to select one of the NTC options on the list for",
"to select one of the NTC options on the list for both Marlin",
"thermistor), in Repetier Firmware (using the same one), it shows 0.00°C, until I",
"the same one), it shows 0.00°C, until I tell the printer to heat",
"option for a 100k thermistor), in Repetier Firmware (using the same one), it",
"temperature sensor is driving me up the wall. I've already checked the wires",
"so I tried to select one of the NTC options on the list",
"list for both Marlin and Repetier and the temp sensor reads steady 3.600°C!!!",
"already checked the wires and connections, but the darn thing keeps showing a",
"i3 MK2). For the hotend, I've bought the Greetech MK8 extruder. However, the",
"printer from mixed parts (a MDF clone of Prusa i3 MK2). For the",
"sensor is driving me up the wall. I've already checked the wires and",
"the 1st option for a 100k thermistor), in Repetier Firmware (using the same",
"the wall. I've already checked the wires and connections, but the darn thing",
"when it shoots to 500°C just like before with Marlin. The documentation for",
"it as a \"100K NTC Thermistor\", so I tried to select one of",
"lists it as a \"100K NTC Thermistor\", so I tried to select one",
"NTC options on the list for both Marlin and Repetier and the temp",
"0.00°C, until I tell the printer to heat up, when it shoots to",
"to 500°C just like before with Marlin. The documentation for this extruder only",
"clone of Prusa i3 MK2). For the hotend, I've bought the Greetech MK8",
"it with the multimeter, it shows around 60k, it's 31°C outside. Is it",
"MK8 extruder. However, the temperature sensor is driving me up the wall. I've",
"both Marlin and Repetier and the temp sensor reads steady 3.600°C!!! Measuring it",
"3.600°C!!! Measuring it with the multimeter, it shows around 60k, it's 31°C outside.",
"Graber i3 printer from mixed parts (a MDF clone of Prusa i3 MK2).",
"the temperature sensor is driving me up the wall. I've already checked the",
"shows around 60k, it's 31°C outside. Is it broken or am I selecting",
"of Prusa i3 MK2). For the hotend, I've bought the Greetech MK8 extruder.",
"Repetier and the temp sensor reads steady 3.600°C!!! Measuring it with the multimeter,",
"I just finish building a Graber i3 printer from mixed parts (a MDF",
"Thermistor\", so I tried to select one of the NTC options on the",
"for both Marlin and Repetier and the temp sensor reads steady 3.600°C!!! Measuring",
"I tell the printer to heat up, when it shoots to 500°C just",
"Celsius. In Marlin, it shows it right up (I'm using the 1st option",
"just like before with Marlin. The documentation for this extruder only lists it",
"it right up (I'm using the 1st option for a 100k thermistor), in",
"bought the Greetech MK8 extruder. However, the temperature sensor is driving me up",
"a 100k thermistor), in Repetier Firmware (using the same one), it shows 0.00°C,",
"connections, but the darn thing keeps showing a steady 500 degrees Celsius. In",
"100k thermistor), in Repetier Firmware (using the same one), it shows 0.00°C, until",
"up (I'm using the 1st option for a 100k thermistor), in Repetier Firmware",
"1st option for a 100k thermistor), in Repetier Firmware (using the same one),",
"tell the printer to heat up, when it shoots to 500°C just like",
"select one of the NTC options on the list for both Marlin and",
"shows it right up (I'm using the 1st option for a 100k thermistor),",
"the multimeter, it shows around 60k, it's 31°C outside. Is it broken or",
"around 60k, it's 31°C outside. Is it broken or am I selecting the",
"steady 3.600°C!!! Measuring it with the multimeter, it shows around 60k, it's 31°C",
"in Repetier Firmware (using the same one), it shows 0.00°C, until I tell",
"a \"100K NTC Thermistor\", so I tried to select one of the NTC",
"keeps showing a steady 500 degrees Celsius. In Marlin, it shows it right",
"MDF clone of Prusa i3 MK2). For the hotend, I've bought the Greetech",
"the list for both Marlin and Repetier and the temp sensor reads steady",
"Repetier Firmware (using the same one), it shows 0.00°C, until I tell the",
"of the NTC options on the list for both Marlin and Repetier and",
"In Marlin, it shows it right up (I'm using the 1st option for",
"steady 500 degrees Celsius. In Marlin, it shows it right up (I'm using",
"multimeter, it shows around 60k, it's 31°C outside. Is it broken or am",
"it shows around 60k, it's 31°C outside. Is it broken or am I",
"extruder. However, the temperature sensor is driving me up the wall. I've already",
"heat up, when it shoots to 500°C just like before with Marlin. The",
"hotend, I've bought the Greetech MK8 extruder. However, the temperature sensor is driving",
"(a MDF clone of Prusa i3 MK2). For the hotend, I've bought the",
"documentation for this extruder only lists it as a \"100K NTC Thermistor\", so",
"is driving me up the wall. I've already checked the wires and connections,",
"I've bought the Greetech MK8 extruder. However, the temperature sensor is driving me",
"wires and connections, but the darn thing keeps showing a steady 500 degrees",
"reads steady 3.600°C!!! Measuring it with the multimeter, it shows around 60k, it's",
"Firmware (using the same one), it shows 0.00°C, until I tell the printer",
"building a Graber i3 printer from mixed parts (a MDF clone of Prusa",
"only lists it as a \"100K NTC Thermistor\", so I tried to select",
"one of the NTC options on the list for both Marlin and Repetier",
"Marlin and Repetier and the temp sensor reads steady 3.600°C!!! Measuring it with",
"with Marlin. The documentation for this extruder only lists it as a \"100K",
"this extruder only lists it as a \"100K NTC Thermistor\", so I tried",
"it shoots to 500°C just like before with Marlin. The documentation for this",
"(using the same one), it shows 0.00°C, until I tell the printer to",
"with the multimeter, it shows around 60k, it's 31°C outside. Is it broken",
"right up (I'm using the 1st option for a 100k thermistor), in Repetier",
"the wires and connections, but the darn thing keeps showing a steady 500",
"Marlin, it shows it right up (I'm using the 1st option for a",
"500°C just like before with Marlin. The documentation for this extruder only lists",
"checked the wires and connections, but the darn thing keeps showing a steady",
"me up the wall. I've already checked the wires and connections, but the",
"thing keeps showing a steady 500 degrees Celsius. In Marlin, it shows it",
"shoots to 500°C just like before with Marlin. The documentation for this extruder",
"for a 100k thermistor), in Repetier Firmware (using the same one), it shows",
"it shows it right up (I'm using the 1st option for a 100k",
"the NTC options on the list for both Marlin and Repetier and the",
"sensor reads steady 3.600°C!!! Measuring it with the multimeter, it shows around 60k,",
"just finish building a Graber i3 printer from mixed parts (a MDF clone",
"temp sensor reads steady 3.600°C!!! Measuring it with the multimeter, it shows around",
"MK2). For the hotend, I've bought the Greetech MK8 extruder. However, the temperature",
"the temp sensor reads steady 3.600°C!!! Measuring it with the multimeter, it shows"
] |
[
"5 V or 6-36 V? What should be the best detecting distance? Should",
"V? What should be the best detecting distance? Should it be 2/4/8 mm.",
"go for M8 or M12 and 5 V or 6-36 V? What should",
"I am confused as to which proximity sensor to use. Should I go",
"which proximity sensor to use. Should I go for M8 or M12 and",
"be the best detecting distance? Should it be 2/4/8 mm. Which one should",
"the best detecting distance? Should it be 2/4/8 mm. Which one should I",
"[dolly](https://andypi.co.uk/2017/09/17/dolly-build-notes-prusa-i3-mk2-clone-3d-printer/) and I am confused as to which proximity sensor to use. Should",
"I go for M8 or M12 and 5 V or 6-36 V? What",
"best detecting distance? Should it be 2/4/8 mm. Which one should I select?",
"am confused as to which proximity sensor to use. Should I go for",
"to which proximity sensor to use. Should I go for M8 or M12",
"M12 and 5 V or 6-36 V? What should be the best detecting",
"6-36 V? What should be the best detecting distance? Should it be 2/4/8",
"confused as to which proximity sensor to use. Should I go for M8",
"should be the best detecting distance? Should it be 2/4/8 mm. Which one",
"a [dolly](https://andypi.co.uk/2017/09/17/dolly-build-notes-prusa-i3-mk2-clone-3d-printer/) and I am confused as to which proximity sensor to use.",
"as to which proximity sensor to use. Should I go for M8 or",
"sensor to use. Should I go for M8 or M12 and 5 V",
"V or 6-36 V? What should be the best detecting distance? Should it",
"Should I go for M8 or M12 and 5 V or 6-36 V?",
"to use. Should I go for M8 or M12 and 5 V or",
"and I am confused as to which proximity sensor to use. Should I",
"proximity sensor to use. Should I go for M8 or M12 and 5",
"am building a [dolly](https://andypi.co.uk/2017/09/17/dolly-build-notes-prusa-i3-mk2-clone-3d-printer/) and I am confused as to which proximity sensor",
"M8 or M12 and 5 V or 6-36 V? What should be the",
"and 5 V or 6-36 V? What should be the best detecting distance?",
"What should be the best detecting distance? Should it be 2/4/8 mm. Which",
"or 6-36 V? What should be the best detecting distance? Should it be",
"for M8 or M12 and 5 V or 6-36 V? What should be",
"building a [dolly](https://andypi.co.uk/2017/09/17/dolly-build-notes-prusa-i3-mk2-clone-3d-printer/) and I am confused as to which proximity sensor to",
"I am building a [dolly](https://andypi.co.uk/2017/09/17/dolly-build-notes-prusa-i3-mk2-clone-3d-printer/) and I am confused as to which proximity",
"or M12 and 5 V or 6-36 V? What should be the best",
"use. Should I go for M8 or M12 and 5 V or 6-36"
] |
[
"increasing the amount of flow a bit, but didn't help (I might need",
"based on the project. But for some reason it is not the case.",
"first layer even though I choose different layer heights based on the project.",
"first layer is supposed to be set at .25mm no matter what the",
"matter what the layer height is otherwise. What do I need to do",
"layer is supposed to be set at .25mm no matter what the layer",
"made a confusing one, so I am rewording a LOT. So the software",
"layer I have it set to .25mm, with the following layers being whatever",
"is not the case. When printing .2mm layer height everything works great. The",
"with the first layer even though I choose different layer heights based on",
"understand what is going wrong. The first layer is supposed to be set",
"But for some reason it is not the case. When printing .2mm layer",
"realized I made a confusing one, so I am rewording a LOT. So",
"have it set to .25mm, with the following layers being whatever I specify",
"printing .2mm layer height everything works great. The print adheres amazing, the nozzle",
"a difference with the first layer even though I choose different layer heights",
"tried increasing the amount of flow a bit, but didn't help (I might",
"didn't help (I might need to raise it a lot more) So I",
"lot more) So I don't understand what is going wrong. The first layer",
"even though I choose different layer heights based on the project. But for",
"is at a really good height. Everything simply works. When printing .1mm the",
"on the project. But for some reason it is not the case. When",
"of flow a bit, but didn't help (I might need to raise it",
"not the case. When printing .2mm layer height everything works great. The print",
"be a difference with the first layer even though I choose different layer",
"height everything works great. The print adheres amazing, the nozzle is at a",
"it is a disaster. Have tried increasing the amount of flow a bit,",
"a disaster. Have tried increasing the amount of flow a bit, but didn't",
".25mm no matter what the layer height is otherwise. What do I need",
"I have it set to .25mm, with the following layers being whatever I",
"the layer height is otherwise. What do I need to do or look",
"works. When printing .1mm the first layer does not stick. A lot less",
"stick. A lot less plastic is coming out the nozzle. And it is",
"amount of flow a bit, but didn't help (I might need to raise",
"heights based on the project. But for some reason it is not the",
"for some reason it is not the case. When printing .2mm layer height",
"Have tried increasing the amount of flow a bit, but didn't help (I",
"the following layers being whatever I specify otherwise. And because of this there",
"disaster. Have tried increasing the amount of flow a bit, but didn't help",
"the project. But for some reason it is not the case. When printing",
"When it comes to the first layer I have it set to .25mm,",
"does not stick. A lot less plastic is coming out the nozzle. And",
"The first layer is supposed to be set at .25mm no matter what",
"height. Everything simply works. When printing .1mm the first layer does not stick.",
"though I choose different layer heights based on the project. But for some",
"the nozzle is at a really good height. Everything simply works. When printing",
"raise it a lot more) So I don't understand what is going wrong.",
"simply works. When printing .1mm the first layer does not stick. A lot",
"A lot less plastic is coming out the nozzle. And it is a",
"The print adheres amazing, the nozzle is at a really good height. Everything",
"the first layer does not stick. A lot less plastic is coming out",
"layers being whatever I specify otherwise. And because of this there shouldn't be",
"bit, but didn't help (I might need to raise it a lot more)",
"printing .1mm the first layer does not stick. A lot less plastic is",
"and realized I made a confusing one, so I am rewording a LOT.",
"am rewording a LOT. So the software I use is Craftware. When it",
"When printing .1mm the first layer does not stick. A lot less plastic",
"shouldn't be a difference with the first layer even though I choose different",
"specify otherwise. And because of this there shouldn't be a difference with the",
"difference with the first layer even though I choose different layer heights based",
".25mm, with the following layers being whatever I specify otherwise. And because of",
"a lot more) So I don't understand what is going wrong. The first",
"When printing .2mm layer height everything works great. The print adheres amazing, the",
"a bit, but didn't help (I might need to raise it a lot",
"to be set at .25mm no matter what the layer height is otherwise.",
"a LOT. So the software I use is Craftware. When it comes to",
"re-read my question and realized I made a confusing one, so I am",
"it a lot more) So I don't understand what is going wrong. The",
"choose different layer heights based on the project. But for some reason it",
"whatever I specify otherwise. And because of this there shouldn't be a difference",
"coming out the nozzle. And it is a disaster. Have tried increasing the",
"layer height everything works great. The print adheres amazing, the nozzle is at",
"rewording a LOT. So the software I use is Craftware. When it comes",
"what the layer height is otherwise. What do I need to do or",
".2mm layer height everything works great. The print adheres amazing, the nozzle is",
"a really good height. Everything simply works. When printing .1mm the first layer",
"is Craftware. When it comes to the first layer I have it set",
"So the software I use is Craftware. When it comes to the first",
"project. But for some reason it is not the case. When printing .2mm",
"I use is Craftware. When it comes to the first layer I have",
"confusing one, so I am rewording a LOT. So the software I use",
"supposed to be set at .25mm no matter what the layer height is",
"less plastic is coming out the nozzle. And it is a disaster. Have",
"don't understand what is going wrong. The first layer is supposed to be",
"great. The print adheres amazing, the nozzle is at a really good height.",
"because of this there shouldn't be a difference with the first layer even",
".1mm the first layer does not stick. A lot less plastic is coming",
"it set to .25mm, with the following layers being whatever I specify otherwise.",
"some reason it is not the case. When printing .2mm layer height everything",
"I specify otherwise. And because of this there shouldn't be a difference with",
"is supposed to be set at .25mm no matter what the layer height",
"need to raise it a lot more) So I don't understand what is",
"comes to the first layer I have it set to .25mm, with the",
"LOT. So the software I use is Craftware. When it comes to the",
"the nozzle. And it is a disaster. Have tried increasing the amount of",
"to raise it a lot more) So I don't understand what is going",
"the software I use is Craftware. When it comes to the first layer",
"different layer heights based on the project. But for some reason it is",
"following layers being whatever I specify otherwise. And because of this there shouldn't",
"the amount of flow a bit, but didn't help (I might need to",
"wrong. The first layer is supposed to be set at .25mm no matter",
"use is Craftware. When it comes to the first layer I have it",
"is a disaster. Have tried increasing the amount of flow a bit, but",
"lot less plastic is coming out the nozzle. And it is a disaster.",
"first layer I have it set to .25mm, with the following layers being",
"Craftware. When it comes to the first layer I have it set to",
"help (I might need to raise it a lot more) So I don't",
"so I am rewording a LOT. So the software I use is Craftware.",
"be set at .25mm no matter what the layer height is otherwise. What",
"(I might need to raise it a lot more) So I don't understand",
"works great. The print adheres amazing, the nozzle is at a really good",
"to .25mm, with the following layers being whatever I specify otherwise. And because",
"this there shouldn't be a difference with the first layer even though I",
"set at .25mm no matter what the layer height is otherwise. What do",
"I re-read my question and realized I made a confusing one, so I",
"being whatever I specify otherwise. And because of this there shouldn't be a",
"what is going wrong. The first layer is supposed to be set at",
"flow a bit, but didn't help (I might need to raise it a",
"going wrong. The first layer is supposed to be set at .25mm no",
"the first layer I have it set to .25mm, with the following layers",
"with the following layers being whatever I specify otherwise. And because of this",
"to the first layer I have it set to .25mm, with the following",
"it comes to the first layer I have it set to .25mm, with",
"is coming out the nozzle. And it is a disaster. Have tried increasing",
"at a really good height. Everything simply works. When printing .1mm the first",
"nozzle. And it is a disaster. Have tried increasing the amount of flow",
"question and realized I made a confusing one, so I am rewording a",
"reason it is not the case. When printing .2mm layer height everything works",
"no matter what the layer height is otherwise. What do I need to",
"case. When printing .2mm layer height everything works great. The print adheres amazing,",
"the case. When printing .2mm layer height everything works great. The print adheres",
"a confusing one, so I am rewording a LOT. So the software I",
"I made a confusing one, so I am rewording a LOT. So the",
"really good height. Everything simply works. When printing .1mm the first layer does",
"And because of this there shouldn't be a difference with the first layer",
"nozzle is at a really good height. Everything simply works. When printing .1mm",
"it is not the case. When printing .2mm layer height everything works great.",
"amazing, the nozzle is at a really good height. Everything simply works. When",
"otherwise. And because of this there shouldn't be a difference with the first",
"more) So I don't understand what is going wrong. The first layer is",
"is going wrong. The first layer is supposed to be set at .25mm",
"of this there shouldn't be a difference with the first layer even though",
"I choose different layer heights based on the project. But for some reason",
"but didn't help (I might need to raise it a lot more) So",
"my question and realized I made a confusing one, so I am rewording",
"might need to raise it a lot more) So I don't understand what",
"I am rewording a LOT. So the software I use is Craftware. When",
"layer does not stick. A lot less plastic is coming out the nozzle.",
"there shouldn't be a difference with the first layer even though I choose",
"good height. Everything simply works. When printing .1mm the first layer does not",
"And it is a disaster. Have tried increasing the amount of flow a",
"adheres amazing, the nozzle is at a really good height. Everything simply works.",
"layer height is otherwise. What do I need to do or look at?",
"layer heights based on the project. But for some reason it is not",
"everything works great. The print adheres amazing, the nozzle is at a really",
"Everything simply works. When printing .1mm the first layer does not stick. A",
"not stick. A lot less plastic is coming out the nozzle. And it",
"out the nozzle. And it is a disaster. Have tried increasing the amount",
"one, so I am rewording a LOT. So the software I use is",
"at .25mm no matter what the layer height is otherwise. What do I",
"So I don't understand what is going wrong. The first layer is supposed",
"I don't understand what is going wrong. The first layer is supposed to",
"software I use is Craftware. When it comes to the first layer I",
"first layer does not stick. A lot less plastic is coming out the",
"the first layer even though I choose different layer heights based on the",
"plastic is coming out the nozzle. And it is a disaster. Have tried",
"set to .25mm, with the following layers being whatever I specify otherwise. And",
"layer even though I choose different layer heights based on the project. But",
"print adheres amazing, the nozzle is at a really good height. Everything simply"
] |
[
"passing that the servo motors for X and Y drive generate a different",
"write g-code to produce not only a tone but even a 2-tone chord.",
"written music to be performed on a 3D printer. Most of us have",
"of us have noticed in passing that the servo motors for X and",
"Harking back to the days of \"singing disk drives,\" I am wondering if",
"in passing that the servo motors for X and Y drive generate a",
"on a 3D printer. Most of us have noticed in passing that the",
"that there's no need to simultaneously produce a print, but that would be",
"-- has this been done? Does anyone want to do so? (Note that",
"am wondering if anyone's written music to be performed on a 3D printer.",
"on motion speed. With some care and experimentation, one could write g-code to",
"done? Does anyone want to do so? (Note that there's no need to",
"motion speed. With some care and experimentation, one could write g-code to produce",
"a 2-tone chord. So -- has this been done? Does anyone want to",
"want to do so? (Note that there's no need to simultaneously produce a",
"a tone but even a 2-tone chord. So -- has this been done?",
"could write g-code to produce not only a tone but even a 2-tone",
"different pitch depending on motion speed. With some care and experimentation, one could",
"us have noticed in passing that the servo motors for X and Y",
"drive generate a different pitch depending on motion speed. With some care and",
"music to be performed on a 3D printer. Most of us have noticed",
"not only a tone but even a 2-tone chord. So -- has this",
"but even a 2-tone chord. So -- has this been done? Does anyone",
"\"singing disk drives,\" I am wondering if anyone's written music to be performed",
"there's no need to simultaneously produce a print, but that would be even",
"do so? (Note that there's no need to simultaneously produce a print, but",
"been done? Does anyone want to do so? (Note that there's no need",
"days of \"singing disk drives,\" I am wondering if anyone's written music to",
"care and experimentation, one could write g-code to produce not only a tone",
"g-code to produce not only a tone but even a 2-tone chord. So",
"(Note that there's no need to simultaneously produce a print, but that would",
"the days of \"singing disk drives,\" I am wondering if anyone's written music",
"anyone want to do so? (Note that there's no need to simultaneously produce",
"wondering if anyone's written music to be performed on a 3D printer. Most",
"Most of us have noticed in passing that the servo motors for X",
"the servo motors for X and Y drive generate a different pitch depending",
"so? (Note that there's no need to simultaneously produce a print, but that",
"this been done? Does anyone want to do so? (Note that there's no",
"pitch depending on motion speed. With some care and experimentation, one could write",
"Does anyone want to do so? (Note that there's no need to simultaneously",
"3D printer. Most of us have noticed in passing that the servo motors",
"printer. Most of us have noticed in passing that the servo motors for",
"of \"singing disk drives,\" I am wondering if anyone's written music to be",
"drives,\" I am wondering if anyone's written music to be performed on a",
"disk drives,\" I am wondering if anyone's written music to be performed on",
"has this been done? Does anyone want to do so? (Note that there's",
"that the servo motors for X and Y drive generate a different pitch",
"even a 2-tone chord. So -- has this been done? Does anyone want",
"Y drive generate a different pitch depending on motion speed. With some care",
"to the days of \"singing disk drives,\" I am wondering if anyone's written",
"back to the days of \"singing disk drives,\" I am wondering if anyone's",
"I am wondering if anyone's written music to be performed on a 3D",
"speed. With some care and experimentation, one could write g-code to produce not",
"With some care and experimentation, one could write g-code to produce not only",
"2-tone chord. So -- has this been done? Does anyone want to do",
"no need to simultaneously produce a print, but that would be even classier).",
"motors for X and Y drive generate a different pitch depending on motion",
"produce not only a tone but even a 2-tone chord. So -- has",
"to produce not only a tone but even a 2-tone chord. So --",
"and experimentation, one could write g-code to produce not only a tone but",
"a different pitch depending on motion speed. With some care and experimentation, one",
"experimentation, one could write g-code to produce not only a tone but even",
"chord. So -- has this been done? Does anyone want to do so?",
"some care and experimentation, one could write g-code to produce not only a",
"to be performed on a 3D printer. Most of us have noticed in",
"be performed on a 3D printer. Most of us have noticed in passing",
"if anyone's written music to be performed on a 3D printer. Most of",
"have noticed in passing that the servo motors for X and Y drive",
"servo motors for X and Y drive generate a different pitch depending on",
"generate a different pitch depending on motion speed. With some care and experimentation,",
"X and Y drive generate a different pitch depending on motion speed. With",
"performed on a 3D printer. Most of us have noticed in passing that",
"anyone's written music to be performed on a 3D printer. Most of us",
"one could write g-code to produce not only a tone but even a",
"to do so? (Note that there's no need to simultaneously produce a print,",
"only a tone but even a 2-tone chord. So -- has this been",
"noticed in passing that the servo motors for X and Y drive generate",
"a 3D printer. Most of us have noticed in passing that the servo",
"and Y drive generate a different pitch depending on motion speed. With some",
"So -- has this been done? Does anyone want to do so? (Note",
"depending on motion speed. With some care and experimentation, one could write g-code",
"tone but even a 2-tone chord. So -- has this been done? Does",
"for X and Y drive generate a different pitch depending on motion speed."
] |
[
"with a 3D printer too? What hardware and material should I use to",
"should I use to do this? Thanks in advance. Sorry for bad english,",
"the counter part's hole to rotate properly? If it's is like 0.05mm, can",
"to work as an axis. And what should be the gap size between",
"of the counter part: [](https://i.stack.imgur.com/XaNBg.png) So, I need to know",
"a little extra gap so it can rotate like an axis. Maybe this",
"This goes inside a counter part, that is carve with the cylinder shape,",
"it's really small with a little system that must be very precise to",
"print that level of detail with a 3D printer too? What hardware and",
"detail with a 3D printer too? What hardware and material should I use",
"system that must be very precise to work. What I have is like",
"be the gap size between the cylinder and the counter part's hole to",
"blender, but it's really small with a little system that must be very",
"the cylinder and the counter part's hole to rotate properly? If it's is",
"be very precise to work. What I have is like a hollow cylinder",
"a model of what I want to print using blender, but it's really",
"to print using blender, but it's really small with a little system that",
"cylinder hard enough to work as an axis. And what should be the",
"that level of detail with a 3D printer too? What hardware and material",
"too? What hardware and material should I use to do this? Thanks in",
"english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is the",
"very precise to work. What I have is like a hollow cylinder with",
"what I want to print using blender, but it's really small with a",
"goes inside a counter part, that is carve with the cylinder shape, but",
"work. What I have is like a hollow cylinder with a diameter of",
"hollow cylinder with a diameter of 11mm, and a thickness of 1mm. This",
"to rotate properly? If it's is like 0.05mm, can I print that level",
"of 1mm. This goes inside a counter part, that is carve with the",
"with a diameter of 11mm, and a thickness of 1mm. This goes inside",
"understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is the depth of the hole)",
"part: [](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's possible",
"picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should be the front",
"to print that cylinder hard enough to work as an axis. And what",
"print using blender, but it's really small with a little system that must",
"diameter of 11mm, and a thickness of 1mm. This goes inside a counter",
"at 3D Printing. I made a model of what I want to print",
"11mm, and a thickness of 1mm. This goes inside a counter part, that",
"must be very precise to work. What I have is like a hollow",
"front view of the counter part: [](https://i.stack.imgur.com/XaNBg.png) So, I need",
"have is like a hollow cylinder with a diameter of 11mm, and a",
"axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should",
"So, I need to know if it's possible to print that cylinder hard",
"an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this",
"it's possible to print that cylinder hard enough to work as an axis.",
"if it's possible to print that cylinder hard enough to work as an",
"cylinder shape, but with a little extra gap so it can rotate like",
"it's is like 0.05mm, can I print that level of detail with a",
"rotate like an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png)",
"little system that must be very precise to work. What I have is",
"carve with the cylinder shape, but with a little extra gap so it",
"shape, but with a little extra gap so it can rotate like an",
"it can rotate like an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/XaNBg.png)",
"between the cylinder and the counter part's hole to rotate properly? If it's",
"What I have is like a hollow cylinder with a diameter of 11mm,",
"like a hollow cylinder with a diameter of 11mm, and a thickness of",
"in advance. Sorry for bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's possible to print that",
"can rotate like an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should be the front view of the",
"view of the counter part: [](https://i.stack.imgur.com/XaNBg.png) So, I need to",
"Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should be",
"properly? If it's is like 0.05mm, can I print that level of detail",
"3D printer too? What hardware and material should I use to do this?",
"the counter part: [](https://i.stack.imgur.com/XaNBg.png) So, I need to know if",
"with a little extra gap so it can rotate like an axis. Maybe",
"possible to print that cylinder hard enough to work as an axis. And",
"with a little system that must be very precise to work. What I",
"small with a little system that must be very precise to work. What",
"part's hole to rotate properly? If it's is like 0.05mm, can I print",
"cylinder and the counter part's hole to rotate properly? If it's is like",
"new at 3D Printing. I made a model of what I want to",
"Thanks in advance. Sorry for bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's",
"to know if it's possible to print that cylinder hard enough to work",
"extra gap so it can rotate like an axis. Maybe this picture explains",
"this? Thanks in advance. Sorry for bad english, I hope you understand! **EDIT:**",
"really small with a little system that must be very precise to work.",
"using blender, but it's really small with a little system that must be",
"can I print that level of detail with a 3D printer too? What",
"like an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And",
"of 11mm, and a thickness of 1mm. This goes inside a counter part,",
"use to do this? Thanks in advance. Sorry for bad english, I hope",
"level of detail with a 3D printer too? What hardware and material should",
"hardware and material should I use to do this? Thanks in advance. Sorry",
"gap size between the cylinder and the counter part's hole to rotate properly?",
"thickness of 1mm. This goes inside a counter part, that is carve with",
"1mm. This goes inside a counter part, that is carve with the cylinder",
"like 0.05mm, can I print that level of detail with a 3D printer",
"should be the gap size between the cylinder and the counter part's hole",
"size between the cylinder and the counter part's hole to rotate properly? If",
"I need to know if it's possible to print that cylinder hard enough",
"this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should be the",
"a diameter of 11mm, and a thickness of 1mm. This goes inside a",
"here](https://i.stack.imgur.com/XaNBg.png)](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's possible to print that cylinder",
"to do this? Thanks in advance. Sorry for bad english, I hope you",
"of detail with a 3D printer too? What hardware and material should I",
"I have is like a hollow cylinder with a diameter of 11mm, and",
"but with a little extra gap so it can rotate like an axis.",
"print that cylinder hard enough to work as an axis. And what should",
"[](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's possible to",
"to work. What I have is like a hollow cylinder with a diameter",
"here](https://i.stack.imgur.com/trZRu.png)](https://i.stack.imgur.com/trZRu.png) And this should be the front view of the counter part: [](https://i.stack.imgur.com/trZRu.png) And this should be the front view of the counter part:",
"is like a hollow cylinder with a diameter of 11mm, and a thickness",
"what should be the gap size between the cylinder and the counter part's",
"3D Printing. I made a model of what I want to print using",
"precise to work. What I have is like a hollow cylinder with a",
"inside a counter part, that is carve with the cylinder shape, but with",
"made a model of what I want to print using blender, but it's",
"that must be very precise to work. What I have is like a",
"part, that is carve with the cylinder shape, but with a little extra",
"counter part, that is carve with the cylinder shape, but with a little",
"an axis. And what should be the gap size between the cylinder and",
"counter part's hole to rotate properly? If it's is like 0.05mm, can I",
"hole to rotate properly? If it's is like 0.05mm, can I print that",
"need to know if it's possible to print that cylinder hard enough to",
"want to print using blender, but it's really small with a little system",
"And this should be the front view of the counter part: [](https://i.stack.imgur.com/trZRu.png) And this should be the front view of",
"do this? Thanks in advance. Sorry for bad english, I hope you understand!",
"I'm new at 3D Printing. I made a model of what I want",
"hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is the depth of",
"be the front view of the counter part: [](https://i.stack.imgur.com/XaNBg.png) So,",
"Printing. I made a model of what I want to print using blender,",
"that is carve with the cylinder shape, but with a little extra gap",
"a little system that must be very precise to work. What I have",
"and material should I use to do this? Thanks in advance. Sorry for",
"as an axis. And what should be the gap size between the cylinder",
"model of what I want to print using blender, but it's really small",
"work as an axis. And what should be the gap size between the",
"What hardware and material should I use to do this? Thanks in advance.",
"And what should be the gap size between the cylinder and the counter",
"bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is",
"image description here](https://i.stack.imgur.com/XaNBg.png)](https://i.stack.imgur.com/XaNBg.png) So, I need to know if it's possible to print",
"so it can rotate like an axis. Maybe this picture explains better: [](https://i.stack.imgur.com/trZRu.png) And this should be the front view",
"is like 0.05mm, can I print that level of detail with a 3D",
"I hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is the depth",
"0.05mm, can I print that level of detail with a 3D printer too?",
"the front view of the counter part: [](https://i.stack.imgur.com/XaNBg.png) So, I",
"a 3D printer too? What hardware and material should I use to do",
"Sorry for bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png)",
"and the counter part's hole to rotate properly? If it's is like 0.05mm,",
"a counter part, that is carve with the cylinder shape, but with a",
"material should I use to do this? Thanks in advance. Sorry for bad",
"you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm is the depth of the",
"and a thickness of 1mm. This goes inside a counter part, that is",
"of what I want to print using blender, but it's really small with",
"hard enough to work as an axis. And what should be the gap",
"I want to print using blender, but it's really small with a little",
"a thickness of 1mm. This goes inside a counter part, that is carve",
"is carve with the cylinder shape, but with a little extra gap so",
"rotate properly? If it's is like 0.05mm, can I print that level of",
"axis. And what should be the gap size between the cylinder and the",
"I made a model of what I want to print using blender, but",
"enough to work as an axis. And what should be the gap size",
"advance. Sorry for bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/trZRu.png) And this should be the front view of the counter",
"for bad english, I hope you understand! **EDIT:** [](https://i.stack.imgur.com/uD2N1.png) (6mm",
"I use to do this? Thanks in advance. Sorry for bad english, I"
] |
[
"built and done some simple tests on a TEVO Tarantula but I've noticed",
"I've disassemble the hot end, changed filament and I can't see any signs",
"I run the calibration with the Titan extruder, *only* the 400 steps is",
"it is pushed all the way down to the hotend, as per the",
"the hotend and calibrate (at 200, 225 and 250°C), I see only ~50",
"showing any signs of melting etc. and it is pushed all the way",
"* When I connect the Bowden tube to the hotend and calibrate (at",
"* Jim Brown's easy config fork of Marlin; * Titan extruder (came with",
"signs of blockage. The Bowden tube in the hotend is not showing any",
"250°C), I see only ~50 mm of extrusion. I've disassemble the hot end,",
"and works as expected; * When I connect the Bowden tube to the",
"updated the firmware with the 400 steps as advised and calibrated the extrusion",
"and it is pushed all the way down to the hotend, as per",
"hotend is not showing any signs of melting etc. and it is pushed",
"Tarantula but I've noticed some pretty dramatic under extrusions. My equipment: * TEVO",
"I connect the Bowden tube to the hotend and calibrate (at 200, 225",
"steps as advised and calibrated the extrusion with the 100 mm method: *",
"Bowden tube in the hotend is not showing any signs of melting etc.",
"under extrusions. My equipment: * TEVO Tarantula; * Jim Brown's easy config fork",
"the 100 mm method: * When I run the calibration with the Titan",
"equipment: * TEVO Tarantula; * Jim Brown's easy config fork of Marlin; *",
"only ~50 mm of extrusion. I've disassemble the hot end, changed filament and",
"fork of Marlin; * Titan extruder (came with printer). I've updated the firmware",
"calibrated the extrusion with the 100 mm method: * When I run the",
"100 mm method: * When I run the calibration with the Titan extruder,",
"Jim Brown's easy config fork of Marlin; * Titan extruder (came with printer).",
"is pushed all the way down to the hotend, as per the instructions.",
"is fine and works as expected; * When I connect the Bowden tube",
"I see only ~50 mm of extrusion. I've disassemble the hot end, changed",
"method: * When I run the calibration with the Titan extruder, *only* the",
"and I can't see any signs of blockage. The Bowden tube in the",
"and 250°C), I see only ~50 mm of extrusion. I've disassemble the hot",
"can't see any signs of blockage. The Bowden tube in the hotend is",
"the Titan extruder, *only* the 400 steps is fine and works as expected;",
"works as expected; * When I connect the Bowden tube to the hotend",
"calibration with the Titan extruder, *only* the 400 steps is fine and works",
"extrusion with the 100 mm method: * When I run the calibration with",
"end, changed filament and I can't see any signs of blockage. The Bowden",
"blockage. The Bowden tube in the hotend is not showing any signs of",
"Tarantula; * Jim Brown's easy config fork of Marlin; * Titan extruder (came",
"changed filament and I can't see any signs of blockage. The Bowden tube",
"run the calibration with the Titan extruder, *only* the 400 steps is fine",
"I've noticed some pretty dramatic under extrusions. My equipment: * TEVO Tarantula; *",
"disassemble the hot end, changed filament and I can't see any signs of",
"(at 200, 225 and 250°C), I see only ~50 mm of extrusion. I've",
"tests on a TEVO Tarantula but I've noticed some pretty dramatic under extrusions.",
"as expected; * When I connect the Bowden tube to the hotend and",
"hot end, changed filament and I can't see any signs of blockage. The",
"400 steps as advised and calibrated the extrusion with the 100 mm method:",
"is not showing any signs of melting etc. and it is pushed all",
"a TEVO Tarantula but I've noticed some pretty dramatic under extrusions. My equipment:",
"advised and calibrated the extrusion with the 100 mm method: * When I",
"filament and I can't see any signs of blockage. The Bowden tube in",
"* Titan extruder (came with printer). I've updated the firmware with the 400",
"etc. and it is pushed all the way down to the hotend, as",
"pretty dramatic under extrusions. My equipment: * TEVO Tarantula; * Jim Brown's easy",
"mm method: * When I run the calibration with the Titan extruder, *only*",
"Brown's easy config fork of Marlin; * Titan extruder (came with printer). I've",
"any signs of melting etc. and it is pushed all the way down",
"see any signs of blockage. The Bowden tube in the hotend is not",
"firmware with the 400 steps as advised and calibrated the extrusion with the",
"When I connect the Bowden tube to the hotend and calibrate (at 200,",
"tube to the hotend and calibrate (at 200, 225 and 250°C), I see",
"and calibrated the extrusion with the 100 mm method: * When I run",
"200, 225 and 250°C), I see only ~50 mm of extrusion. I've disassemble",
"of blockage. The Bowden tube in the hotend is not showing any signs",
"calibrate (at 200, 225 and 250°C), I see only ~50 mm of extrusion.",
"as advised and calibrated the extrusion with the 100 mm method: * When",
"on a TEVO Tarantula but I've noticed some pretty dramatic under extrusions. My",
"done some simple tests on a TEVO Tarantula but I've noticed some pretty",
"config fork of Marlin; * Titan extruder (came with printer). I've updated the",
"225 and 250°C), I see only ~50 mm of extrusion. I've disassemble the",
"to the hotend and calibrate (at 200, 225 and 250°C), I see only",
"pushed all the way down to the hotend, as per the instructions. So,",
"with the 400 steps as advised and calibrated the extrusion with the 100",
"the 400 steps as advised and calibrated the extrusion with the 100 mm",
"the calibration with the Titan extruder, *only* the 400 steps is fine and",
"simple tests on a TEVO Tarantula but I've noticed some pretty dramatic under",
"all the way down to the hotend, as per the instructions. So, what's",
"but I've noticed some pretty dramatic under extrusions. My equipment: * TEVO Tarantula;",
"extrusions. My equipment: * TEVO Tarantula; * Jim Brown's easy config fork of",
"melting etc. and it is pushed all the way down to the hotend,",
"I've updated the firmware with the 400 steps as advised and calibrated the",
"* TEVO Tarantula; * Jim Brown's easy config fork of Marlin; * Titan",
"any signs of blockage. The Bowden tube in the hotend is not showing",
"TEVO Tarantula; * Jim Brown's easy config fork of Marlin; * Titan extruder",
"steps is fine and works as expected; * When I connect the Bowden",
"tube in the hotend is not showing any signs of melting etc. and",
"with printer). I've updated the firmware with the 400 steps as advised and",
"Titan extruder (came with printer). I've updated the firmware with the 400 steps",
"extruder, *only* the 400 steps is fine and works as expected; * When",
"way down to the hotend, as per the instructions. So, what's going with",
"Marlin; * Titan extruder (came with printer). I've updated the firmware with the",
"Titan extruder, *only* the 400 steps is fine and works as expected; *",
"the Bowden tube to the hotend and calibrate (at 200, 225 and 250°C),",
"I can't see any signs of blockage. The Bowden tube in the hotend",
"of Marlin; * Titan extruder (came with printer). I've updated the firmware with",
"easy config fork of Marlin; * Titan extruder (came with printer). I've updated",
"expected; * When I connect the Bowden tube to the hotend and calibrate",
"extrusion. I've disassemble the hot end, changed filament and I can't see any",
"~50 mm of extrusion. I've disassemble the hot end, changed filament and I",
"the 400 steps is fine and works as expected; * When I connect",
"the hot end, changed filament and I can't see any signs of blockage.",
"hotend and calibrate (at 200, 225 and 250°C), I see only ~50 mm",
"I've built and done some simple tests on a TEVO Tarantula but I've",
"noticed some pretty dramatic under extrusions. My equipment: * TEVO Tarantula; * Jim",
"the hotend is not showing any signs of melting etc. and it is",
"not showing any signs of melting etc. and it is pushed all the",
"When I run the calibration with the Titan extruder, *only* the 400 steps",
"fine and works as expected; * When I connect the Bowden tube to",
"down to the hotend, as per the instructions. So, what's going with this?",
"mm of extrusion. I've disassemble the hot end, changed filament and I can't",
"dramatic under extrusions. My equipment: * TEVO Tarantula; * Jim Brown's easy config",
"the firmware with the 400 steps as advised and calibrated the extrusion with",
"Bowden tube to the hotend and calibrate (at 200, 225 and 250°C), I",
"the way down to the hotend, as per the instructions. So, what's going",
"and calibrate (at 200, 225 and 250°C), I see only ~50 mm of",
"printer). I've updated the firmware with the 400 steps as advised and calibrated",
"extruder (came with printer). I've updated the firmware with the 400 steps as",
"with the Titan extruder, *only* the 400 steps is fine and works as",
"*only* the 400 steps is fine and works as expected; * When I",
"and done some simple tests on a TEVO Tarantula but I've noticed some",
"the extrusion with the 100 mm method: * When I run the calibration",
"with the 100 mm method: * When I run the calibration with the",
"in the hotend is not showing any signs of melting etc. and it",
"TEVO Tarantula but I've noticed some pretty dramatic under extrusions. My equipment: *",
"(came with printer). I've updated the firmware with the 400 steps as advised",
"connect the Bowden tube to the hotend and calibrate (at 200, 225 and",
"some pretty dramatic under extrusions. My equipment: * TEVO Tarantula; * Jim Brown's",
"of melting etc. and it is pushed all the way down to the",
"The Bowden tube in the hotend is not showing any signs of melting",
"My equipment: * TEVO Tarantula; * Jim Brown's easy config fork of Marlin;",
"400 steps is fine and works as expected; * When I connect the",
"see only ~50 mm of extrusion. I've disassemble the hot end, changed filament",
"of extrusion. I've disassemble the hot end, changed filament and I can't see",
"* When I run the calibration with the Titan extruder, *only* the 400",
"signs of melting etc. and it is pushed all the way down to",
"some simple tests on a TEVO Tarantula but I've noticed some pretty dramatic"
] |
[
"commonly printed plastic which I can buy that might be transparent to UV",
"to UV light? I wish to print a mould, then pour in my",
"wish to print a mould, then pour in my plastic which requires a",
"Is there any commonly printed plastic which I can buy that might be",
"can buy that might be transparent to UV light? I wish to print",
"print a mould, then pour in my plastic which requires a UV light",
"transparent to UV light? I wish to print a mould, then pour in",
"might be transparent to UV light? I wish to print a mould, then",
"buy that might be transparent to UV light? I wish to print a",
"pour in my plastic which requires a UV light to activate the curing",
"there any commonly printed plastic which I can buy that might be transparent",
"light? I wish to print a mould, then pour in my plastic which",
"then pour in my plastic which requires a UV light to activate the",
"a mould, then pour in my plastic which requires a UV light to",
"to print a mould, then pour in my plastic which requires a UV",
"plastic which I can buy that might be transparent to UV light? I",
"I can buy that might be transparent to UV light? I wish to",
"be transparent to UV light? I wish to print a mould, then pour",
"any commonly printed plastic which I can buy that might be transparent to",
"which I can buy that might be transparent to UV light? I wish",
"printed plastic which I can buy that might be transparent to UV light?",
"that might be transparent to UV light? I wish to print a mould,",
"UV light? I wish to print a mould, then pour in my plastic",
"in my plastic which requires a UV light to activate the curing process.",
"I wish to print a mould, then pour in my plastic which requires",
"mould, then pour in my plastic which requires a UV light to activate"
] |
[
"extruder starts clicking, I tried adjusting the voltage with no luck, it's still",
"it's still clicking. And it doesn't extrude a lot of plastic sometimes it",
"doesn't extrude a lot of plastic sometimes it even stops extruding but the",
"with no luck, it's still clicking. And it doesn't extrude a lot of",
"it even stops extruding but the extruder is still turning. Can someone help?",
"clicking. And it doesn't extrude a lot of plastic sometimes it even stops",
"still clicking. And it doesn't extrude a lot of plastic sometimes it even",
"Whenever it start printing the extruder starts clicking, I tried adjusting the voltage",
"it doesn't extrude a lot of plastic sometimes it even stops extruding but",
"clicking, I tried adjusting the voltage with no luck, it's still clicking. And",
"tried adjusting the voltage with no luck, it's still clicking. And it doesn't",
"adjusting the voltage with no luck, it's still clicking. And it doesn't extrude",
"of plastic sometimes it even stops extruding but the extruder is still turning.",
"And it doesn't extrude a lot of plastic sometimes it even stops extruding",
"no luck, it's still clicking. And it doesn't extrude a lot of plastic",
"extrude a lot of plastic sometimes it even stops extruding but the extruder",
"the voltage with no luck, it's still clicking. And it doesn't extrude a",
"a lot of plastic sometimes it even stops extruding but the extruder is",
"printing the extruder starts clicking, I tried adjusting the voltage with no luck,",
"plastic sometimes it even stops extruding but the extruder is still turning. Can",
"lot of plastic sometimes it even stops extruding but the extruder is still",
"it start printing the extruder starts clicking, I tried adjusting the voltage with",
"luck, it's still clicking. And it doesn't extrude a lot of plastic sometimes",
"sometimes it even stops extruding but the extruder is still turning. Can someone",
"starts clicking, I tried adjusting the voltage with no luck, it's still clicking.",
"start printing the extruder starts clicking, I tried adjusting the voltage with no",
"I tried adjusting the voltage with no luck, it's still clicking. And it",
"the extruder starts clicking, I tried adjusting the voltage with no luck, it's",
"voltage with no luck, it's still clicking. And it doesn't extrude a lot"
] |
[
"settings in slicer, and earlier I was printing non-vase mode and the prints",
"vase mode settings in slicer, and earlier I was printing non-vase mode and",
"I was printing non-vase mode and the prints came out fine. Layer height",
"I noticed my printer underextruding badly. The settings have not been changed from",
"the prints came out fine. Layer height is 0.2 mm and perimeter width",
"came out fine. Layer height is 0.2 mm and perimeter width is 0.3",
"height is 0.2 mm and perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg",
"time printing in vase mode, and I noticed my printer underextruding badly. The",
"first time printing in vase mode, and I noticed my printer underextruding badly.",
"extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion",
"[![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under",
"and I noticed my printer underextruding badly. The settings have not been changed",
"and the prints came out fine. Layer height is 0.2 mm and perimeter",
"have not been changed from default vase mode settings in slicer, and earlier",
"changed from default vase mode settings in slicer, and earlier I was printing",
"and perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under",
"was printing non-vase mode and the prints came out fine. Layer height is",
"is 0.2 mm and perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under",
"is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under",
"noticed my printer underextruding badly. The settings have not been changed from default",
"settings have not been changed from default vase mode settings in slicer, and",
"perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion",
"in vase mode, and I noticed my printer underextruding badly. The settings have",
"printer underextruding badly. The settings have not been changed from default vase mode",
"\"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion #2\")](https://i.stack.imgur.com/KCy5X.jpg \"Under",
"extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion #2\")](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion",
"vase mode, and I noticed my printer underextruding badly. The settings have not",
"Layer height is 0.2 mm and perimeter width is 0.3 mm. [![Under extrusion",
"mode settings in slicer, and earlier I was printing non-vase mode and the",
"earlier I was printing non-vase mode and the prints came out fine. Layer",
"#1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion #2\")](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion #2\")",
"slicer, and earlier I was printing non-vase mode and the prints came out",
"from default vase mode settings in slicer, and earlier I was printing non-vase",
"mode and the prints came out fine. Layer height is 0.2 mm and",
"mode, and I noticed my printer underextruding badly. The settings have not been",
"0.2 mm and perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion",
"my printer underextruding badly. The settings have not been changed from default vase",
"0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion",
"#1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg \"Under extrusion #2\")](https://i.stack.imgur.com/KCy5X.jpg",
"been changed from default vase mode settings in slicer, and earlier I was",
"mm and perimeter width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg",
"width is 0.3 mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")",
"non-vase mode and the prints came out fine. Layer height is 0.2 mm",
"It's my first time printing in vase mode, and I noticed my printer",
"fine. Layer height is 0.2 mm and perimeter width is 0.3 mm. [![Under",
"badly. The settings have not been changed from default vase mode settings in",
"default vase mode settings in slicer, and earlier I was printing non-vase mode",
"printing in vase mode, and I noticed my printer underextruding badly. The settings",
"mm. [![Under extrusion #1](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\")](https://i.stack.imgur.com/rXiKt.jpg \"Under extrusion #1\") [![Under extrusion #2](https://i.stack.imgur.com/KCy5X.jpg",
"The settings have not been changed from default vase mode settings in slicer,",
"printing non-vase mode and the prints came out fine. Layer height is 0.2",
"prints came out fine. Layer height is 0.2 mm and perimeter width is",
"not been changed from default vase mode settings in slicer, and earlier I",
"my first time printing in vase mode, and I noticed my printer underextruding",
"underextruding badly. The settings have not been changed from default vase mode settings",
"out fine. Layer height is 0.2 mm and perimeter width is 0.3 mm.",
"and earlier I was printing non-vase mode and the prints came out fine.",
"in slicer, and earlier I was printing non-vase mode and the prints came"
] |
[
"1.4 * 0.9 angle stepper motors * DRV8825 drivers configured at 0.8V Vref",
"* Robotdyn RAMPS 1.4 * 0.9 angle stepper motors * DRV8825 drivers configured",
"above, two of them show the weird movement and the other shows me",
"my problem in the videos above, two of them show the weird movement",
"clicking on the home button repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0",
"two of them show the weird movement and the other shows me clicking",
"* DRV8825 drivers configured at 0.8V Vref * Anet A2 Plus stock for",
"to illustrate my problem in the videos above, two of them show the",
"in the videos above, two of them show the weird movement and the",
"DRV8825 drivers configured at 0.8V Vref * Anet A2 Plus stock for all",
"weird movement and the other shows me clicking on the home button repeatedly.",
"<https://photos.app.goo.gl/O6yPf3sDeV1yhS0C2> I tried to illustrate my problem in the videos above, two of",
"problem in the videos above, two of them show the weird movement and",
"RAMPS 1.4 * 0.9 angle stepper motors * DRV8825 drivers configured at 0.8V",
"the other shows me clicking on the home button repeatedly. Some Info: *",
"the weird movement and the other shows me clicking on the home button",
"shows me clicking on the home button repeatedly. Some Info: * Marlin 1.1.8",
"and the other shows me clicking on the home button repeatedly. Some Info:",
"0.9 angle stepper motors * DRV8825 drivers configured at 0.8V Vref * Anet",
"Robotdyn RAMPS 1.4 * 0.9 angle stepper motors * DRV8825 drivers configured at",
"I tried to illustrate my problem in the videos above, two of them",
"both) * Robotdyn RAMPS 1.4 * 0.9 angle stepper motors * DRV8825 drivers",
"the videos above, two of them show the weird movement and the other",
"on the home button repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0 (same",
"home button repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0 (same problem in",
"other shows me clicking on the home button repeatedly. Some Info: * Marlin",
"show the weird movement and the other shows me clicking on the home",
"* 0.9 angle stepper motors * DRV8825 drivers configured at 0.8V Vref *",
"Marlin 1.1.8 or 2.0.0 (same problem in both) * Robotdyn RAMPS 1.4 *",
"tried to illustrate my problem in the videos above, two of them show",
"of them show the weird movement and the other shows me clicking on",
"(same problem in both) * Robotdyn RAMPS 1.4 * 0.9 angle stepper motors",
"2.0.0 (same problem in both) * Robotdyn RAMPS 1.4 * 0.9 angle stepper",
"configured at 0.8V Vref * Anet A2 Plus stock for all the rest",
"* Marlin 1.1.8 or 2.0.0 (same problem in both) * Robotdyn RAMPS 1.4",
"them show the weird movement and the other shows me clicking on the",
"videos above, two of them show the weird movement and the other shows",
"drivers configured at 0.8V Vref * Anet A2 Plus stock for all the",
"Info: * Marlin 1.1.8 or 2.0.0 (same problem in both) * Robotdyn RAMPS",
"or 2.0.0 (same problem in both) * Robotdyn RAMPS 1.4 * 0.9 angle",
"in both) * Robotdyn RAMPS 1.4 * 0.9 angle stepper motors * DRV8825",
"repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0 (same problem in both) *",
"Some Info: * Marlin 1.1.8 or 2.0.0 (same problem in both) * Robotdyn",
"illustrate my problem in the videos above, two of them show the weird",
"me clicking on the home button repeatedly. Some Info: * Marlin 1.1.8 or",
"angle stepper motors * DRV8825 drivers configured at 0.8V Vref * Anet A2",
"motors * DRV8825 drivers configured at 0.8V Vref * Anet A2 Plus stock",
"button repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0 (same problem in both)",
"movement and the other shows me clicking on the home button repeatedly. Some",
"problem in both) * Robotdyn RAMPS 1.4 * 0.9 angle stepper motors *",
"stepper motors * DRV8825 drivers configured at 0.8V Vref * Anet A2 Plus",
"1.1.8 or 2.0.0 (same problem in both) * Robotdyn RAMPS 1.4 * 0.9",
"the home button repeatedly. Some Info: * Marlin 1.1.8 or 2.0.0 (same problem"
] |
[
"design software which support designing multi-material parts. I will be printing on a",
"for 3D design software which support designing multi-material parts. I will be printing",
"a geometry file which slic3r (or some other slicing software) will properly process?",
"or any alternative. My question is, what is available for 3D design software",
"printing on a multi-extruder machine based on RepRap firmware. The printer will handle",
"single-material, so I am looking for something like AMF files, or any alternative.",
"properly process? I'm not asking for opinions on which software is best. I",
"other slicing software) will properly process? I'm not asking for opinions on which",
"g-code file given the right input. STL seems to be single-material, so I",
"software is best. I believe this is my first question in any StackExchange",
"to be single-material, so I am looking for something like AMF files, or",
"StackExchange forum, so if I have trespassed on community standards, it was not",
"I am looking for something like AMF files, or any alternative. My question",
"any alternative. My question is, what is available for 3D design software which",
"software) will properly process? I'm not asking for opinions on which software is",
"is my first question in any StackExchange forum, so if I have trespassed",
"a proper g-code file. Slic3r will produce a proper g-code file given the",
"software which will produce a geometry file which slic3r (or some other slicing",
"looking for something like AMF files, or any alternative. My question is, what",
"be single-material, so I am looking for something like AMF files, or any",
"will produce a proper g-code file given the right input. STL seems to",
"right input. STL seems to be single-material, so I am looking for something",
"slicing software) will properly process? I'm not asking for opinions on which software",
"on which software is best. I believe this is my first question in",
"file given the right input. STL seems to be single-material, so I am",
"on a multi-extruder machine based on RepRap firmware. The printer will handle the",
"proper g-code file given the right input. STL seems to be single-material, so",
"software which support designing multi-material parts. I will be printing on a multi-extruder",
"The printer will handle the files when given a proper g-code file. Slic3r",
"which slic3r (or some other slicing software) will properly process? I'm not asking",
"the files when given a proper g-code file. Slic3r will produce a proper",
"is best. I believe this is my first question in any StackExchange forum,",
"My question is, what is available for 3D design software which will produce",
"am looking for something like AMF files, or any alternative. My question is,",
"suggestions for 3D design software which support designing multi-material parts. I will be",
"be printing on a multi-extruder machine based on RepRap firmware. The printer will",
"my first question in any StackExchange forum, so if I have trespassed on",
"I believe this is my first question in any StackExchange forum, so if",
"geometry file which slic3r (or some other slicing software) will properly process? I'm",
"3D design software which will produce a geometry file which slic3r (or some",
"a proper g-code file given the right input. STL seems to be single-material,",
"the right input. STL seems to be single-material, so I am looking for",
"asking for opinions on which software is best. I believe this is my",
"I'm looking for suggestions for 3D design software which support designing multi-material parts.",
"question is, what is available for 3D design software which will produce a",
"I'm not asking for opinions on which software is best. I believe this",
"produce a proper g-code file given the right input. STL seems to be",
"given a proper g-code file. Slic3r will produce a proper g-code file given",
"which software is best. I believe this is my first question in any",
"first question in any StackExchange forum, so if I have trespassed on community",
"what is available for 3D design software which will produce a geometry file",
"so if I have trespassed on community standards, it was not my intention.",
"firmware. The printer will handle the files when given a proper g-code file.",
"STL seems to be single-material, so I am looking for something like AMF",
"multi-extruder machine based on RepRap firmware. The printer will handle the files when",
"believe this is my first question in any StackExchange forum, so if I",
"I will be printing on a multi-extruder machine based on RepRap firmware. The",
"AMF files, or any alternative. My question is, what is available for 3D",
"will produce a geometry file which slic3r (or some other slicing software) will",
"files when given a proper g-code file. Slic3r will produce a proper g-code",
"for something like AMF files, or any alternative. My question is, what is",
"best. I believe this is my first question in any StackExchange forum, so",
"files, or any alternative. My question is, what is available for 3D design",
"which will produce a geometry file which slic3r (or some other slicing software)",
"for 3D design software which will produce a geometry file which slic3r (or",
"is, what is available for 3D design software which will produce a geometry",
"something like AMF files, or any alternative. My question is, what is available",
"process? I'm not asking for opinions on which software is best. I believe",
"for suggestions for 3D design software which support designing multi-material parts. I will",
"based on RepRap firmware. The printer will handle the files when given a",
"opinions on which software is best. I believe this is my first question",
"input. STL seems to be single-material, so I am looking for something like",
"this is my first question in any StackExchange forum, so if I have",
"support designing multi-material parts. I will be printing on a multi-extruder machine based",
"will handle the files when given a proper g-code file. Slic3r will produce",
"printer will handle the files when given a proper g-code file. Slic3r will",
"(or some other slicing software) will properly process? I'm not asking for opinions",
"3D design software which support designing multi-material parts. I will be printing on",
"question in any StackExchange forum, so if I have trespassed on community standards,",
"forum, so if I have trespassed on community standards, it was not my",
"file. Slic3r will produce a proper g-code file given the right input. STL",
"multi-material parts. I will be printing on a multi-extruder machine based on RepRap",
"will properly process? I'm not asking for opinions on which software is best.",
"on RepRap firmware. The printer will handle the files when given a proper",
"is available for 3D design software which will produce a geometry file which",
"when given a proper g-code file. Slic3r will produce a proper g-code file",
"some other slicing software) will properly process? I'm not asking for opinions on",
"produce a geometry file which slic3r (or some other slicing software) will properly",
"any StackExchange forum, so if I have trespassed on community standards, it was",
"g-code file. Slic3r will produce a proper g-code file given the right input.",
"slic3r (or some other slicing software) will properly process? I'm not asking for",
"seems to be single-material, so I am looking for something like AMF files,",
"proper g-code file. Slic3r will produce a proper g-code file given the right",
"designing multi-material parts. I will be printing on a multi-extruder machine based on",
"given the right input. STL seems to be single-material, so I am looking",
"available for 3D design software which will produce a geometry file which slic3r",
"machine based on RepRap firmware. The printer will handle the files when given",
"looking for suggestions for 3D design software which support designing multi-material parts. I",
"like AMF files, or any alternative. My question is, what is available for",
"parts. I will be printing on a multi-extruder machine based on RepRap firmware.",
"Slic3r will produce a proper g-code file given the right input. STL seems",
"alternative. My question is, what is available for 3D design software which will",
"handle the files when given a proper g-code file. Slic3r will produce a",
"will be printing on a multi-extruder machine based on RepRap firmware. The printer",
"for opinions on which software is best. I believe this is my first",
"which support designing multi-material parts. I will be printing on a multi-extruder machine",
"design software which will produce a geometry file which slic3r (or some other",
"in any StackExchange forum, so if I have trespassed on community standards, it",
"file which slic3r (or some other slicing software) will properly process? I'm not",
"a multi-extruder machine based on RepRap firmware. The printer will handle the files",
"so I am looking for something like AMF files, or any alternative. My",
"not asking for opinions on which software is best. I believe this is",
"RepRap firmware. The printer will handle the files when given a proper g-code"
] |
[
"printer head and putting it back together. I have printed with the printer",
"I have a Cura profile I can upload if that will help. Any",
"work. I have tried adjusting feedrate, flow rate, retraction amount and speed, temperature,",
"a lot of PLA filament and failed prints) to no avail. I will",
"clear and ensuring that the edges allow the filament to pass through. -",
"print](https://i.stack.imgur.com/ZcvdG.jpg)](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting the temperate between 190 up",
"of the whole assembly (they work, they aren't jammed etc.) - Dissambling the",
"regards to 3D printers. I also know that this is a popular issue",
"have this clogging problem on my 3D printer that I am having a",
"having a really hard time to solve. I am a hobbiest so in",
"print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting",
"ensuring that the edges allow the filament to pass through. - Check if",
"started and no matter what I change on the profile it won't work.",
"how the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following:",
"I have this clogging problem on my 3D printer that I am having",
"prints) to no avail. I will try to describe the problem and what",
"filament and failed prints) to no avail. I will try to describe the",
"to show the clog](https://i.stack.imgur.com/OremM.jpg)](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The next image",
"that the edges allow the filament to pass through. - Check if the",
"allow the filament to pass through. - Check if the cooling fans work",
"between 190 up to 220 for the PLA filament. Everything trying a print",
"through a lot of PLA filament and failed prints) to no avail. I",
"returned to PLA this issue started and no matter what I change on",
"Checking the Teflon pipe inside the tube if it is clear and ensuring",
"my 3D printer that I am having a really hard time to solve.",
"- Adjusting the temperate between 190 up to 220 for the PLA filament.",
"much appreciated. I have been struggling with this for a while now and",
"describe the problem and what I have tried to solve it. First the",
"tried to solve it. First the issue:[](https://i.stack.imgur.com/OremM.jpg) This",
"I have printed with the printer before without a problem. I printed PETG",
"clog](https://i.stack.imgur.com/OremM.jpg)](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The next image shows the assembled",
"image shows the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is",
"for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when it",
"work, they aren't jammed etc.) - Dissambling the printer head and putting it",
"will help. Any advise would be much appreciated. I have been struggling with",
"way am I a professional with regards to 3D printers. I also know",
"failed prints) to no avail. I will try to describe the problem and",
"issue and I have tried a lot of the proposed solutions (going through",
"show the clog](https://i.stack.imgur.com/OremM.jpg)](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The next image shows",
"the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the",
"- Dissambling the printer head and putting it back together. I have printed",
"the cooling fans work well to ensure cooling of the whole assembly (they",
"and the results were decent. When I returned to PLA this issue started",
"it won't work. I have tried adjusting feedrate, flow rate, retraction amount and",
"won't work. I have tried adjusting feedrate, flow rate, retraction amount and speed,",
"tried adjusting feedrate, flow rate, retraction amount and speed, temperature, fan speeds to",
"a few times to get that working and the results were decent. When",
"- Checking the Teflon pipe inside the tube if it is clear and",
"the clog](https://i.stack.imgur.com/OremM.jpg)](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The next image shows the",
"aren't jammed etc.) - Dissambling the printer head and putting it back together.",
"am I a professional with regards to 3D printers. I also know that",
"the following: - Adjusting the temperate between 190 up to 220 for the",
"it. - Doing a thorough cleaning of the nozzle (Acetone soak, wire brush,",
"is how the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the",
"thorough cleaning of the nozzle (Acetone soak, wire brush, guitar string etc.) -",
"- Doing a thorough cleaning of the nozzle (Acetone soak, wire brush, guitar",
"of PLA filament and failed prints) to no avail. I will try to",
"wire brush, guitar string etc.) - Checking the Teflon pipe inside the tube",
"printers. I also know that this is a popular issue and I have",
"tried the following: - Adjusting the temperate between 190 up to 220 for",
"cleaning of the nozzle (Acetone soak, wire brush, guitar string etc.) - Checking",
"shows the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how",
"results were decent. When I returned to PLA this issue started and no",
"I change on the profile it won't work. I have tried adjusting feedrate,",
"this clogging problem on my 3D printer that I am having a really",
"few things. I have a Cura profile I can upload if that will",
"it back together. I have printed with the printer before without a problem.",
"following: - Adjusting the temperate between 190 up to 220 for the PLA",
"temperate between 190 up to 220 for the PLA filament. Everything trying a",
"fan speeds to name but a few things. I have a Cura profile",
"brush, guitar string etc.) - Checking the Teflon pipe inside the tube if",
"the proposed solutions (going through a lot of PLA filament and failed prints)",
"been struggling with this for a while now and really need some options.",
"the whole assembly (they work, they aren't jammed etc.) - Dissambling the printer",
"were decent. When I returned to PLA this issue started and no matter",
"work well to ensure cooling of the whole assembly (they work, they aren't",
"solutions (going through a lot of PLA filament and failed prints) to no",
"jammed etc.) - Dissambling the printer head and putting it back together. I",
"printed PETG a few times to get that working and the results were",
"speed, temperature, fan speeds to name but a few things. I have a",
"times to get that working and the results were decent. When I returned",
"help. Any advise would be much appreciated. I have been struggling with this",
"it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting the temperate between",
"clogs. The next image shows the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the print",
"advise would be much appreciated. I have been struggling with this for a",
"guitar string etc.) - Checking the Teflon pipe inside the tube if it",
"things. I have a Cura profile I can upload if that will help.",
"appreciated. I have been struggling with this for a while now and really",
"Adjusting the temperate between 190 up to 220 for the PLA filament. Everything",
"head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when",
"so in no way am I a professional with regards to 3D printers.",
"hortend to show the clog](https://i.stack.imgur.com/OremM.jpg)](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The next",
"etc.) - Dissambling the printer head and putting it back together. I have",
"a lot of the proposed solutions (going through a lot of PLA filament",
"it. First the issue:[](https://i.stack.imgur.com/OremM.jpg) This shows how the",
"next image shows the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This",
"I have tried a lot of the proposed solutions (going through a lot",
"time to solve. I am a hobbiest so in no way am I",
"the filament clogs. The next image shows the assembled printer head for reference.:",
"Teflon pipe inside the tube if it is clear and ensuring that the",
"When I returned to PLA this issue started and no matter what I",
"soak, wire brush, guitar string etc.) - Checking the Teflon pipe inside the",
"decent. When I returned to PLA this issue started and no matter what",
"to PLA this issue started and no matter what I change on the",
"(Acetone soak, wire brush, guitar string etc.) - Checking the Teflon pipe inside",
"and failed prints) to no avail. I will try to describe the problem",
"I also know that this is a popular issue and I have tried",
"[](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg)",
"220 for the PLA filament. Everything trying a print with it. - Doing",
"with it. - Doing a thorough cleaning of the nozzle (Acetone soak, wire",
"Doing a thorough cleaning of the nozzle (Acetone soak, wire brush, guitar string",
"I am having a really hard time to solve. I am a hobbiest",
"edges allow the filament to pass through. - Check if the cooling fans",
"through. - Check if the cooling fans work well to ensure cooling of",
"assembly (they work, they aren't jammed etc.) - Dissambling the printer head and",
"putting it back together. I have printed with the printer before without a",
"I am a hobbiest so in no way am I a professional with",
"nozzle (Acetone soak, wire brush, guitar string etc.) - Checking the Teflon pipe",
"that will help. Any advise would be much appreciated. I have been struggling",
"- Check if the cooling fans work well to ensure cooling of the",
"printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks",
"matter what I change on the profile it won't work. I have tried",
"that this is a popular issue and I have tried a lot of",
"I returned to PLA this issue started and no matter what I change",
"a problem. I printed PETG a few times to get that working and",
"clogging problem on my 3D printer that I am having a really hard",
"cooling fans work well to ensure cooling of the whole assembly (they work,",
"adjusting feedrate, flow rate, retraction amount and speed, temperature, fan speeds to name",
"also know that this is a popular issue and I have tried a",
"temperature, fan speeds to name but a few things. I have a Cura",
"well to ensure cooling of the whole assembly (they work, they aren't jammed",
"will try to describe the problem and what I have tried to solve",
"the problem and what I have tried to solve it. First the issue:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting the temperate between 190",
"pass through. - Check if the cooling fans work well to ensure cooling",
"printer before without a problem. I printed PETG a few times to get",
"this issue started and no matter what I change on the profile it",
"know that this is a popular issue and I have tried a lot",
"popular issue and I have tried a lot of the proposed solutions (going",
"profile it won't work. I have tried adjusting feedrate, flow rate, retraction amount",
"how the filament clogs. The next image shows the assembled printer head for",
"tried a lot of the proposed solutions (going through a lot of PLA",
"the nozzle (Acetone soak, wire brush, guitar string etc.) - Checking the Teflon",
"the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: -",
"am a hobbiest so in no way am I a professional with regards",
"etc.) - Checking the Teflon pipe inside the tube if it is clear",
"lot of the proposed solutions (going through a lot of PLA filament and",
"of the nozzle (Acetone soak, wire brush, guitar string etc.) - Checking the",
"but a few things. I have a Cura profile I can upload if",
"back together. I have printed with the printer before without a problem. I",
"the Teflon pipe inside the tube if it is clear and ensuring that",
"a really hard time to solve. I am a hobbiest so in no",
"PLA filament and failed prints) to no avail. I will try to describe",
"have tried the following: - Adjusting the temperate between 190 up to 220",
"no matter what I change on the profile it won't work. I have",
"to name but a few things. I have a Cura profile I can",
"name but a few things. I have a Cura profile I can upload",
"a few things. I have a Cura profile I can upload if that",
"3D printers. I also know that this is a popular issue and I",
"the profile it won't work. I have tried adjusting feedrate, flow rate, retraction",
"with regards to 3D printers. I also know that this is a popular",
"looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting the",
"tube if it is clear and ensuring that the edges allow the filament",
"this is a popular issue and I have tried a lot of the",
"the printer before without a problem. I printed PETG a few times to",
"(they work, they aren't jammed etc.) - Dissambling the printer head and putting",
"and speed, temperature, fan speeds to name but a few things. I have",
"a professional with regards to 3D printers. I also know that this is",
"a thorough cleaning of the nozzle (Acetone soak, wire brush, guitar string etc.)",
"to 3D printers. I also know that this is a popular issue and",
"amount and speed, temperature, fan speeds to name but a few things. I",
"pipe inside the tube if it is clear and ensuring that the edges",
"The next image shows the assembled printer head for reference.: [](https://i.stack.imgur.com/AhioD.jpg)",
"that I am having a really hard time to solve. I am a",
"what I change on the profile it won't work. I have tried adjusting",
"Everything trying a print with it. - Doing a thorough cleaning of the",
"I have been struggling with this for a while now and really need",
"reference.: [](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when it fails:[](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs.",
"have tried adjusting feedrate, flow rate, retraction amount and speed, temperature, fan speeds",
"rate, retraction amount and speed, temperature, fan speeds to name but a few",
"in no way am I a professional with regards to 3D printers. I",
"have tried to solve it. First the issue:[](https://i.stack.imgur.com/OremM.jpg)",
"print with it. - Doing a thorough cleaning of the nozzle (Acetone soak,",
"professional with regards to 3D printers. I also know that this is a",
"solve it. First the issue:[](https://i.stack.imgur.com/OremM.jpg) This shows how",
"have a Cura profile I can upload if that will help. Any advise",
"flow rate, retraction amount and speed, temperature, fan speeds to name but a",
"and I have tried a lot of the proposed solutions (going through a",
"Check if the cooling fans work well to ensure cooling of the whole",
"to ensure cooling of the whole assembly (they work, they aren't jammed etc.)",
"fans work well to ensure cooling of the whole assembly (they work, they",
"a hobbiest so in no way am I a professional with regards to",
"printed with the printer before without a problem. I printed PETG a few",
"to solve. I am a hobbiest so in no way am I a",
"head and putting it back together. I have printed with the printer before",
"I a professional with regards to 3D printers. I also know that this",
"would be much appreciated. I have been struggling with this for a while",
"try to describe the problem and what I have tried to solve it.",
"without a problem. I printed PETG a few times to get that working",
"I can upload if that will help. Any advise would be much appreciated.",
"lot of PLA filament and failed prints) to no avail. I will try",
"string etc.) - Checking the Teflon pipe inside the tube if it is",
"it is clear and ensuring that the edges allow the filament to pass",
"I will try to describe the problem and what I have tried to",
"up to 220 for the PLA filament. Everything trying a print with it.",
"the filament to pass through. - Check if the cooling fans work well",
"with the printer before without a problem. I printed PETG a few times",
"speeds to name but a few things. I have a Cura profile I",
"if it is clear and ensuring that the edges allow the filament to",
"a Cura profile I can upload if that will help. Any advise would",
"issue started and no matter what I change on the profile it won't",
"solve. I am a hobbiest so in no way am I a professional",
"change on the profile it won't work. I have tried adjusting feedrate, flow",
"of the proposed solutions (going through a lot of PLA filament and failed",
"no way am I a professional with regards to 3D printers. I also",
"head](https://i.stack.imgur.com/AhioD.jpg)](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have",
"profile I can upload if that will help. Any advise would be much",
"to solve it. First the issue:[](https://i.stack.imgur.com/OremM.jpg) This shows",
"a popular issue and I have tried a lot of the proposed solutions",
"the tube if it is clear and ensuring that the edges allow the",
"together. I have printed with the printer before without a problem. I printed",
"to describe the problem and what I have tried to solve it. First",
"problem. I printed PETG a few times to get that working and the",
"what I have tried to solve it. First the issue:[](https://i.stack.imgur.com/AhioD.jpg) This is how the print looks when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I",
"can upload if that will help. Any advise would be much appreciated. I",
"First the issue:[](https://i.stack.imgur.com/OremM.jpg) This shows how the filament",
"am having a really hard time to solve. I am a hobbiest so",
"issue:[](https://i.stack.imgur.com/OremM.jpg) This shows how the filament clogs. The",
"filament to pass through. - Check if the cooling fans work well to",
"really hard time to solve. I am a hobbiest so in no way",
"This shows how the filament clogs. The next image shows the assembled printer",
"few times to get that working and the results were decent. When I",
"and putting it back together. I have printed with the printer before without",
"ensure cooling of the whole assembly (they work, they aren't jammed etc.) -",
"I have tried adjusting feedrate, flow rate, retraction amount and speed, temperature, fan",
"Any advise would be much appreciated. I have been struggling with this for",
"and what I have tried to solve it. First the issue:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried",
"to get that working and the results were decent. When I returned to",
"when it fails:[](https://i.stack.imgur.com/ZcvdG.jpg) I have tried the following: - Adjusting the temperate",
"have been struggling with this for a while now and really need some",
"I have tried to solve it. First the issue:[![Removed hortend to show the",
"(going through a lot of PLA filament and failed prints) to no avail.",
"shows how the filament clogs. The next image shows the assembled printer head",
"trying a print with it. - Doing a thorough cleaning of the nozzle",
"and no matter what I change on the profile it won't work. I",
"have printed with the printer before without a problem. I printed PETG a",
"get that working and the results were decent. When I returned to PLA",
"have tried a lot of the proposed solutions (going through a lot of",
"working and the results were decent. When I returned to PLA this issue",
"I printed PETG a few times to get that working and the results",
"that working and the results were decent. When I returned to PLA this",
"upload if that will help. Any advise would be much appreciated. I have",
"the temperate between 190 up to 220 for the PLA filament. Everything trying",
"PLA filament. Everything trying a print with it. - Doing a thorough cleaning",
"to pass through. - Check if the cooling fans work well to ensure",
"Cura profile I can upload if that will help. Any advise would be"
] |
[
"this dilemma. I am using a Prusa I3 printer with PLA, trying to",
"of this irksome issues. I can of course provide more in depth details,",
"have adjusted the flow rate, the speed, the layer height, temperature, and nothing",
"including a pic of what i am getting. Any Ideas?[](https://i.stack.imgur.com/vr1tx.jpg)",
"is fairly important. I seem to have gotten all the settings dialed in",
"for model horses, so quality is fairly important. I seem to have gotten",
"dialed in just the way I want them and for the most part,",
"of the first layer. But its not every time. It seems like it",
"first, the filament does not follow the curves of the first layer. But",
"filament is going around the curve of the top of the horseshoe on",
"for the company I work for. They are for model horses, so quality",
"the top of the horseshoe on layers beyond the first, the filament does",
"the 2nd or 3rd Layers that are doing it. I have adjusted the",
"want them and for the most part, the prints come out fine. There",
"is just the 2nd or 3rd Layers that are doing it. I have",
"course provide more in depth details, and am including a pic of what",
"quality is fairly important. I seem to have gotten all the settings dialed",
"have gotten all the settings dialed in just the way I want them",
"adjusted the flow rate, the speed, the layer height, temperature, and nothing seems",
"the company I work for. They are for model horses, so quality is",
"PLA, trying to print horseshoes for the company I work for. They are",
"to print horseshoes for the company I work for. They are for model",
"When the filament is going around the curve of the top of the",
"the most part, the prints come out fine. There is however one annoying",
"dilemma. I am using a Prusa I3 printer with PLA, trying to print",
"on google and not found any answers to this dilemma. I am using",
"way I want them and for the most part, the prints come out",
"temperature, and nothing seems to get rid of this irksome issues. I can",
"model horses, so quality is fairly important. I seem to have gotten all",
"searching around on google and not found any answers to this dilemma. I",
"layer height, temperature, and nothing seems to get rid of this irksome issues.",
"in just the way I want them and for the most part, the",
"There is however one annoying thing that keeps happening. When the filament is",
"and am including a pic of what i am getting. Any Ideas?[![enter image",
"I have adjusted the flow rate, the speed, the layer height, temperature, and",
"is going around the curve of the top of the horseshoe on layers",
"fairly important. I seem to have gotten all the settings dialed in just",
"answers to this dilemma. I am using a Prusa I3 printer with PLA,",
"the speed, the layer height, temperature, and nothing seems to get rid of",
"that keeps happening. When the filament is going around the curve of the",
"every time. It seems like it is just the 2nd or 3rd Layers",
"fine. There is however one annoying thing that keeps happening. When the filament",
"horseshoe on layers beyond the first, the filament does not follow the curves",
"rid of this irksome issues. I can of course provide more in depth",
"I have been searching around on google and not found any answers to",
"not follow the curves of the first layer. But its not every time.",
"been searching around on google and not found any answers to this dilemma.",
"more in depth details, and am including a pic of what i am",
"company I work for. They are for model horses, so quality is fairly",
"the layer height, temperature, and nothing seems to get rid of this irksome",
"the curve of the top of the horseshoe on layers beyond the first,",
"one annoying thing that keeps happening. When the filament is going around the",
"in depth details, and am including a pic of what i am getting.",
"I work for. They are for model horses, so quality is fairly important.",
"and nothing seems to get rid of this irksome issues. I can of",
"just the 2nd or 3rd Layers that are doing it. I have adjusted",
"it. I have adjusted the flow rate, the speed, the layer height, temperature,",
"I3 printer with PLA, trying to print horseshoes for the company I work",
"thing that keeps happening. When the filament is going around the curve of",
"height, temperature, and nothing seems to get rid of this irksome issues. I",
"happening. When the filament is going around the curve of the top of",
"seems like it is just the 2nd or 3rd Layers that are doing",
"on layers beyond the first, the filament does not follow the curves of",
"to this dilemma. I am using a Prusa I3 printer with PLA, trying",
"it is just the 2nd or 3rd Layers that are doing it. I",
"using a Prusa I3 printer with PLA, trying to print horseshoes for the",
"gotten all the settings dialed in just the way I want them and",
"come out fine. There is however one annoying thing that keeps happening. When",
"them and for the most part, the prints come out fine. There is",
"found any answers to this dilemma. I am using a Prusa I3 printer",
"prints come out fine. There is however one annoying thing that keeps happening.",
"and not found any answers to this dilemma. I am using a Prusa",
"or 3rd Layers that are doing it. I have adjusted the flow rate,",
"rate, the speed, the layer height, temperature, and nothing seems to get rid",
"get rid of this irksome issues. I can of course provide more in",
"am using a Prusa I3 printer with PLA, trying to print horseshoes for",
"for the most part, the prints come out fine. There is however one",
"that are doing it. I have adjusted the flow rate, the speed, the",
"the way I want them and for the most part, the prints come",
"its not every time. It seems like it is just the 2nd or",
"speed, the layer height, temperature, and nothing seems to get rid of this",
"Prusa I3 printer with PLA, trying to print horseshoes for the company I",
"all the settings dialed in just the way I want them and for",
"beyond the first, the filament does not follow the curves of the first",
"the flow rate, the speed, the layer height, temperature, and nothing seems to",
"trying to print horseshoes for the company I work for. They are for",
"print horseshoes for the company I work for. They are for model horses,",
"the curves of the first layer. But its not every time. It seems",
"this irksome issues. I can of course provide more in depth details, and",
"They are for model horses, so quality is fairly important. I seem to",
"part, the prints come out fine. There is however one annoying thing that",
"printer with PLA, trying to print horseshoes for the company I work for.",
"filament does not follow the curves of the first layer. But its not",
"depth details, and am including a pic of what i am getting. Any",
"horses, so quality is fairly important. I seem to have gotten all the",
"a Prusa I3 printer with PLA, trying to print horseshoes for the company",
"irksome issues. I can of course provide more in depth details, and am",
"2nd or 3rd Layers that are doing it. I have adjusted the flow",
"curves of the first layer. But its not every time. It seems like",
"important. I seem to have gotten all the settings dialed in just the",
"issues. I can of course provide more in depth details, and am including",
"I can of course provide more in depth details, and am including a",
"and for the most part, the prints come out fine. There is however",
"however one annoying thing that keeps happening. When the filament is going around",
"details, and am including a pic of what i am getting. Any Ideas?[![enter",
"google and not found any answers to this dilemma. I am using a",
"work for. They are for model horses, so quality is fairly important. I",
"for. They are for model horses, so quality is fairly important. I seem",
"around the curve of the top of the horseshoe on layers beyond the",
"the horseshoe on layers beyond the first, the filament does not follow the",
"settings dialed in just the way I want them and for the most",
"nothing seems to get rid of this irksome issues. I can of course",
"the settings dialed in just the way I want them and for the",
"the filament does not follow the curves of the first layer. But its",
"any answers to this dilemma. I am using a Prusa I3 printer with",
"curve of the top of the horseshoe on layers beyond the first, the",
"is however one annoying thing that keeps happening. When the filament is going",
"going around the curve of the top of the horseshoe on layers beyond",
"not every time. It seems like it is just the 2nd or 3rd",
"am including a pic of what i am getting. Any Ideas?[![enter image description",
"provide more in depth details, and am including a pic of what i",
"the first layer. But its not every time. It seems like it is",
"Layers that are doing it. I have adjusted the flow rate, the speed,",
"the prints come out fine. There is however one annoying thing that keeps",
"out fine. There is however one annoying thing that keeps happening. When the",
"time. It seems like it is just the 2nd or 3rd Layers that",
"most part, the prints come out fine. There is however one annoying thing",
"like it is just the 2nd or 3rd Layers that are doing it.",
"of course provide more in depth details, and am including a pic of",
"can of course provide more in depth details, and am including a pic",
"have been searching around on google and not found any answers to this",
"I am using a Prusa I3 printer with PLA, trying to print horseshoes",
"annoying thing that keeps happening. When the filament is going around the curve",
"horseshoes for the company I work for. They are for model horses, so",
"are for model horses, so quality is fairly important. I seem to have",
"flow rate, the speed, the layer height, temperature, and nothing seems to get",
"keeps happening. When the filament is going around the curve of the top",
"top of the horseshoe on layers beyond the first, the filament does not",
"I want them and for the most part, the prints come out fine.",
"3rd Layers that are doing it. I have adjusted the flow rate, the",
"just the way I want them and for the most part, the prints",
"does not follow the curves of the first layer. But its not every",
"But its not every time. It seems like it is just the 2nd",
"with PLA, trying to print horseshoes for the company I work for. They",
"of the top of the horseshoe on layers beyond the first, the filament",
"first layer. But its not every time. It seems like it is just",
"seem to have gotten all the settings dialed in just the way I",
"around on google and not found any answers to this dilemma. I am",
"the filament is going around the curve of the top of the horseshoe",
"are doing it. I have adjusted the flow rate, the speed, the layer",
"of the horseshoe on layers beyond the first, the filament does not follow",
"It seems like it is just the 2nd or 3rd Layers that are",
"to get rid of this irksome issues. I can of course provide more",
"to have gotten all the settings dialed in just the way I want",
"doing it. I have adjusted the flow rate, the speed, the layer height,",
"seems to get rid of this irksome issues. I can of course provide",
"so quality is fairly important. I seem to have gotten all the settings",
"I seem to have gotten all the settings dialed in just the way",
"follow the curves of the first layer. But its not every time. It",
"layers beyond the first, the filament does not follow the curves of the",
"not found any answers to this dilemma. I am using a Prusa I3",
"the first, the filament does not follow the curves of the first layer.",
"layer. But its not every time. It seems like it is just the"
] |
[
"i3 mk2s, using PLA, 210 °C (clean from what I can tell) nozzle,",
"4 for details). Where these support layers touch the outer brim, they adhere",
"touch the outer brim. They go down with a little bit of \"squeeze",
"on a genuine Prosi i3 mk2s, using PLA, 210 °C (clean from what",
"big starting foot print. I am printing on a genuine Prosi i3 mk2s,",
"close to the subsequent, broader strokes of the rest of the support layer,",
"print the support layers for the \"actual\" layers that will get printed first.",
"printer does a 180-degree turn. (this can be seen on the right hand",
"first picture). Then, it attempts to print the whole-of-base support structure (refer to",
"there is a section of \"fine\" support material that sort of survived. [](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in PC",
"in red) are either not adhering well enough, or somehow getting \"ruffled up\",",
"condition) heat bed. My model is an STL from Thingiverse, and I sliced",
"too close to the subsequent, broader strokes of the rest of the support",
"happening, is the small sections that get printed first (circled in red) are",
"No actual contact of object to bed here. Also, as a side note,",
"and usually don't have issues printing objects with support (although typically these have",
"bed. At the right, there is a section of \"fine\" support material that",
"with a little bit of \"squeeze out\" when the printer does a 180-degree",
"(circled in red) are either not adhering well enough, or somehow getting \"ruffled",
"attempts to print the whole-of-base support structure (refer to pic 3 and 4",
"bed, so not a big starting foot print. I am printing on a",
"sections. Having 2 densities of support layer per layer seems to be causing",
"calibration, etc. Only thing that might be a bit out is my z-axis",
"print bed as well) After it prints the brim (which adheres well), it",
"Slicing in Prosi control (part 1): shows the different support structures and very",
"a side note, why the funny diagonal line cutting through the rest of",
"print. I am printing on a genuine Prosi i3 mk2s, using PLA, 210",
"the initial support layer sections, it tears them up, leaving a big mess.",
"that touch the print bed, so not a big starting foot print. I",
"I can tell) nozzle, 60 °C (clean, good condition) heat bed. My model",
"a few curved surfaces that touch the print bed, so not a big",
"will get printed first. These layers do not touch the outer brim. They",
"to 3D printing, and having difficulty printing first layer of an object with",
"might be a bit out is my z-axis might be a *fraction* too",
"seen on the right hand end of first picture). Then, it attempts to",
"support. The object has a few curved surfaces that touch the print bed,",
"run the printer calibration, z-axis calibration, etc. Only thing that might be a",
"layers that will get printed first. These layers do not touch the outer",
"these support layers touch the outer brim, they adhere well. When they touch",
"Then, it attempts to print the whole-of-base support structure (refer to pic 3",
"180-degree turn. (this can be seen on the right hand end of first",
"\"squeeze out\" when the printer does a 180-degree turn. (this can be seen",
"At the right, there is a section of \"fine\" support material that sort",
"The broad strokes seem to adhere well except for when they meet where",
"actual object to the bed (orange) [](https://i.stack.imgur.com/RMFL5.png) Close up",
"little bit of \"squeeze out\" when the printer does a 180-degree turn. (this",
"support structure (refer to pic 3 and 4 for details). Where these support",
"to adhere well except for when they meet where the fine layer was",
"(part 1): shows the different support structures and very minimal contact of actual",
"too low. I have no issues when printing objects without support, and usually",
"and having difficulty printing first layer of an object with support. The object",
"layer, such that when the rest of the support layer is printed, it",
"the bed (orange) [](https://i.stack.imgur.com/RMFL5.png) Close up of other problem",
"red) are either not adhering well enough, or somehow getting \"ruffled up\", or",
"Only thing that might be a bit out is my z-axis might be",
"- after that it's just a big mess. [](https://i.stack.imgur.com/rEmXD.jpg)",
"mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows",
"print the whole-of-base support structure (refer to pic 3 and 4 for details).",
"object to the print bed as well) After it prints the brim (which",
"surfaces that touch the print bed, so not a big starting foot print.",
"(orange) [](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in",
"(clean from what I can tell) nozzle, 60 °C (clean, good condition) heat",
"to pic 3 and 4 for details). Where these support layers touch the",
"leaving a big mess. What appears to me to be happening, is the",
"per layer seems to be causing issues. Failed print, still on the bed.",
"an STL from Thingiverse, and I sliced it with Prosi Control. Settings: 0.3",
"structures and very minimal contact of actual object to the bed (orange) [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows the different support",
"They go down with a little bit of \"squeeze out\" when the printer",
"issues printing objects with support (although typically these have a larger contact area",
"thing that might be a bit out is my z-axis might be a",
"be causing issues. Failed print, still on the bed. At the right, there",
"the different support structures and very minimal contact of actual object to the",
"the outer brim. They go down with a little bit of \"squeeze out\"",
"a big mess. What appears to me to be happening, is the small",
"area in PC slicing. No actual contact of object to bed here. Also,",
"1): shows the different support structures and very minimal contact of actual object",
"for the \"actual\" layers that will get printed first. These layers do not",
"well. When they touch the initial support layer sections, it tears them up,",
"issues when printing objects without support, and usually don't have issues printing objects",
"a section of \"fine\" support material that sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg)",
"the failed first layer. The broad strokes seem to adhere well except for",
"60 °C (clean, good condition) heat bed. My model is an STL from",
"0.3 mm layers, 30 % infill, Support from build plate, brim on. I",
"have run the printer calibration, z-axis calibration, etc. Only thing that might be",
"210 °C (clean from what I can tell) nozzle, 60 °C (clean, good",
"they touch the initial support layer sections, it tears them up, leaving a",
"Close up of other problem area in PC slicing. No actual contact of",
"mess. What appears to me to be happening, is the small sections that",
"The object has a few curved surfaces that touch the print bed, so",
"they meet where the fine layer was - after that it's just a",
"up of other problem area in PC slicing. No actual contact of object",
"*fraction* too low. I have no issues when printing objects without support, and",
"to bed here. Also, as a side note, why the funny diagonal line",
"mk2s, using PLA, 210 °C (clean from what I can tell) nozzle, 60",
"layer sections, it tears them up, leaving a big mess. What appears to",
"control first layer 1](https://i.stack.imgur.com/RMFL5.png)](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in PC slicing.",
"the object to the print bed as well) After it prints the brim",
"printed, it is tearing up the initial small sections. Having 2 densities of",
"don't have issues printing objects with support (although typically these have a larger",
"of the support layer is printed, it is tearing up the initial small",
"up](https://i.stack.imgur.com/rEmXD.jpg)](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows the different support structures and",
"larger contact area of the object to the print bed as well) After",
"strokes of the rest of the support layer, such that when the rest",
"the subsequent, broader strokes of the rest of the support layer, such that",
"the support layer, such that when the rest of the support layer is",
"well) After it prints the brim (which adheres well), it tries to print",
"(this can be seen on the right hand end of first picture). Then,",
"a big mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part",
"the whole-of-base support structure (refer to pic 3 and 4 for details). Where",
"such that when the rest of the support layer is printed, it is",
"sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer.",
"starting foot print. I am printing on a genuine Prosi i3 mk2s, using",
"as a side note, why the funny diagonal line cutting through the rest",
"printing on a genuine Prosi i3 mk2s, using PLA, 210 °C (clean from",
"be a *fraction* too low. I have no issues when printing objects without",
"Control. Settings: 0.3 mm layers, 30 % infill, Support from build plate, brim",
"of the rest of the support layer, such that when the rest of",
"it tries to print the support layers for the \"actual\" layers that will",
"tell) nozzle, 60 °C (clean, good condition) heat bed. My model is an",
"prints the brim (which adheres well), it tries to print the support layers",
"2 densities of support layer per layer seems to be causing issues. Failed",
"support layers touch the outer brim, they adhere well. When they touch the",
"a 180-degree turn. (this can be seen on the right hand end of",
"sections, it tears them up, leaving a big mess. What appears to me",
"to be happening, is the small sections that get printed first (circled in",
"issues. Failed print, still on the bed. At the right, there is a",
"of \"fine\" support material that sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close up",
"plate, brim on. I have run the printer calibration, z-axis calibration, etc. Only",
"to be causing issues. Failed print, still on the bed. At the right,",
"1](https://i.stack.imgur.com/RMFL5.png)](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in PC slicing. No actual contact",
"the small sections that get printed first (circled in red) are either not",
"touch the print bed, so not a big starting foot print. I am",
"Settings: 0.3 mm layers, 30 % infill, Support from build plate, brim on.",
"of other problem area in PC slicing. No actual contact of object to",
"out\" when the printer does a 180-degree turn. (this can be seen on",
"contact area of the object to the print bed as well) After it",
"that it's just a big mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in",
"these have a larger contact area of the object to the print bed",
"rest of the support layer is printed, it is tearing up the initial",
"Where these support layers touch the outer brim, they adhere well. When they",
"When they touch the initial support layer sections, it tears them up, leaving",
"seems to be causing issues. Failed print, still on the bed. At the",
"are printed too close to the subsequent, broader strokes of the rest of",
"good condition) heat bed. My model is an STL from Thingiverse, and I",
"of first picture). Then, it attempts to print the whole-of-base support structure (refer",
"Close up of the failed first layer. The broad strokes seem to adhere",
"why the funny diagonal line cutting through the rest of the support structure",
"Also, as a side note, why the funny diagonal line cutting through the",
"first layer of an object with support. The object has a few curved",
"bit of \"squeeze out\" when the printer does a 180-degree turn. (this can",
"section of \"fine\" support material that sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close",
"printed too close to the subsequent, broader strokes of the rest of the",
"layers touch the outer brim, they adhere well. When they touch the initial",
"Thingiverse, and I sliced it with Prosi Control. Settings: 0.3 mm layers, 30",
"the print bed as well) After it prints the brim (which adheres well),",
"the print bed, so not a big starting foot print. I am printing",
"fine layer was - after that it's just a big mess. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first",
"adhere well except for when they meet where the fine layer was -",
"the right hand end of first picture). Then, it attempts to print the",
"have no issues when printing objects without support, and usually don't have issues",
"broader strokes of the rest of the support layer, such that when the",
"be happening, is the small sections that get printed first (circled in red)",
"shows the different support structures and very minimal contact of actual object to",
"z-axis calibration, etc. Only thing that might be a bit out is my",
"with Prosi Control. Settings: 0.3 mm layers, 30 % infill, Support from build",
"of an object with support. The object has a few curved surfaces that",
"layers for the \"actual\" layers that will get printed first. These layers do",
"of \"squeeze out\" when the printer does a 180-degree turn. (this can be",
"area of the object to the print bed as well) After it prints",
"outer brim. They go down with a little bit of \"squeeze out\" when",
"are either not adhering well enough, or somehow getting \"ruffled up\", or are",
"material that sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed",
"the initial small sections. Having 2 densities of support layer per layer seems",
"when the rest of the support layer is printed, it is tearing up",
"they adhere well. When they touch the initial support layer sections, it tears",
"layer seems to be causing issues. Failed print, still on the bed. At",
"up of the failed first layer. The broad strokes seem to adhere well",
"can be seen on the right hand end of first picture). Then, it",
"when they meet where the fine layer was - after that it's just",
"seem to adhere well except for when they meet where the fine layer",
"objects with support (although typically these have a larger contact area of the",
"me to be happening, is the small sections that get printed first (circled",
"be a bit out is my z-axis might be a *fraction* too low.",
"it's just a big mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi",
"PLA, 210 °C (clean from what I can tell) nozzle, 60 °C (clean,",
"first layer](https://i.stack.imgur.com/NKa4E.jpg)](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer. The broad strokes seem",
"except for when they meet where the fine layer was - after that",
"just a big mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control",
"first layer 1](https://i.stack.imgur.com/RMFL5.png)](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in PC slicing. No",
"Having 2 densities of support layer per layer seems to be causing issues.",
"small sections. Having 2 densities of support layer per layer seems to be",
"big mess. [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1):",
"big mess. What appears to me to be happening, is the small sections",
"°C (clean from what I can tell) nozzle, 60 °C (clean, good condition)",
"an object with support. The object has a few curved surfaces that touch",
"tears them up, leaving a big mess. What appears to me to be",
"no issues when printing objects without support, and usually don't have issues printing",
"does a 180-degree turn. (this can be seen on the right hand end",
"contact of actual object to the bed (orange) [](https://i.stack.imgur.com/RMFL5.png)",
"infill, Support from build plate, brim on. I have run the printer calibration,",
"the funny diagonal line cutting through the rest of the support structure here?",
"not adhering well enough, or somehow getting \"ruffled up\", or are printed too",
"the fine layer was - after that it's just a big mess. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of",
"and I sliced it with Prosi Control. Settings: 0.3 mm layers, 30 %",
"other problem area in PC slicing. No actual contact of object to bed",
"be seen on the right hand end of first picture). Then, it attempts",
"well), it tries to print the support layers for the \"actual\" layers that",
"support material that sort of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the",
"of survived. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer. The",
"through the rest of the support structure here? [](https://i.stack.imgur.com/4belv.png)",
"very minimal contact of actual object to the bed (orange) [](https://i.stack.imgur.com/RMFL5.png) Close",
"using PLA, 210 °C (clean from what I can tell) nozzle, 60 °C",
"the support layers for the \"actual\" layers that will get printed first. These",
"support layer is printed, it is tearing up the initial small sections. Having",
"on the bed. At the right, there is a section of \"fine\" support",
"up\", or are printed too close to the subsequent, broader strokes of the",
"them up, leaving a big mess. What appears to me to be happening,",
"that might be a bit out is my z-axis might be a *fraction*",
"sections that get printed first (circled in red) are either not adhering well",
"support layer sections, it tears them up, leaving a big mess. What appears",
"heat bed. My model is an STL from Thingiverse, and I sliced it",
"enough, or somehow getting \"ruffled up\", or are printed too close to the",
"I am printing on a genuine Prosi i3 mk2s, using PLA, 210 °C",
"[](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer. The broad strokes",
"not touch the outer brim. They go down with a little bit of",
"failed first layer. The broad strokes seem to adhere well except for when",
"bed (orange) [](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area",
"% infill, Support from build plate, brim on. I have run the printer",
"broad strokes seem to adhere well except for when they meet where the",
"have issues printing objects with support (although typically these have a larger contact",
"of the support layer, such that when the rest of the support layer",
"small sections that get printed first (circled in red) are either not adhering",
"[](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows the",
"Failed print, still on the bed. At the right, there is a section",
"is tearing up the initial small sections. Having 2 densities of support layer",
"strokes seem to adhere well except for when they meet where the fine",
"control (part 1): shows the different support structures and very minimal contact of",
"so not a big starting foot print. I am printing on a genuine",
"contact of object to bed here. Also, as a side note, why the",
"Support from build plate, brim on. I have run the printer calibration, z-axis",
"nozzle, 60 °C (clean, good condition) heat bed. My model is an STL",
"PC slicing. No actual contact of object to bed here. Also, as a",
"layer. The broad strokes seem to adhere well except for when they meet",
"in Prosi control (part 1): shows the different support structures and very minimal",
"that get printed first (circled in red) are either not adhering well enough,",
"with support (although typically these have a larger contact area of the object",
"difficulty printing first layer of an object with support. The object has a",
"when printing objects without support, and usually don't have issues printing objects with",
"that will get printed first. These layers do not touch the outer brim.",
"minimal contact of actual object to the bed (orange) [](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows the different support structures",
"either not adhering well enough, or somehow getting \"ruffled up\", or are printed",
"is printed, it is tearing up the initial small sections. Having 2 densities",
"is the small sections that get printed first (circled in red) are either",
"to print the whole-of-base support structure (refer to pic 3 and 4 for",
"it prints the brim (which adheres well), it tries to print the support",
"actual contact of object to bed here. Also, as a side note, why",
"a larger contact area of the object to the print bed as well)",
"brim (which adheres well), it tries to print the support layers for the",
"object has a few curved surfaces that touch the print bed, so not",
"line cutting through the rest of the support structure here? [](https://i.stack.imgur.com/RMFL5.png) Close up of other",
"subsequent, broader strokes of the rest of the support layer, such that when",
"where the fine layer was - after that it's just a big mess.",
"I sliced it with Prosi Control. Settings: 0.3 mm layers, 30 % infill,",
"model is an STL from Thingiverse, and I sliced it with Prosi Control.",
"the support layer is printed, it is tearing up the initial small sections.",
"pic 3 and 4 for details). Where these support layers touch the outer",
"from Thingiverse, and I sliced it with Prosi Control. Settings: 0.3 mm layers,",
"well enough, or somehow getting \"ruffled up\", or are printed too close to",
"a big starting foot print. I am printing on a genuine Prosi i3",
"getting \"ruffled up\", or are printed too close to the subsequent, broader strokes",
"°C (clean, good condition) heat bed. My model is an STL from Thingiverse,",
"first layer close up](https://i.stack.imgur.com/rEmXD.jpg)](https://i.stack.imgur.com/rEmXD.jpg) Slicing in Prosi control (part 1): shows the different",
"a little bit of \"squeeze out\" when the printer does a 180-degree turn.",
"have a larger contact area of the object to the print bed as",
"of support layer per layer seems to be causing issues. Failed print, still",
"of the object to the print bed as well) After it prints the",
"support, and usually don't have issues printing objects with support (although typically these",
"bed as well) After it prints the brim (which adheres well), it tries",
"appears to me to be happening, is the small sections that get printed",
"touch the initial support layer sections, it tears them up, leaving a big",
"These layers do not touch the outer brim. They go down with a",
"layer](https://i.stack.imgur.com/NKa4E.jpg)](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer. The broad strokes seem to",
"my z-axis might be a *fraction* too low. I have no issues when",
"right hand end of first picture). Then, it attempts to print the whole-of-base",
"it tears them up, leaving a big mess. What appears to me to",
"cutting through the rest of the support structure here? [](https://i.stack.imgur.com/rEmXD.jpg) Slicing",
"rest of the support layer, such that when the rest of the support",
"side note, why the funny diagonal line cutting through the rest of the",
"layers, 30 % infill, Support from build plate, brim on. I have run",
"(although typically these have a larger contact area of the object to the",
"objects without support, and usually don't have issues printing objects with support (although",
"causing issues. Failed print, still on the bed. At the right, there is",
"can tell) nozzle, 60 °C (clean, good condition) heat bed. My model is",
"initial small sections. Having 2 densities of support layer per layer seems to",
"still on the bed. At the right, there is a section of \"fine\"",
"object with support. The object has a few curved surfaces that touch the",
"I am quite new to 3D printing, and having difficulty printing first layer",
"a genuine Prosi i3 mk2s, using PLA, 210 °C (clean from what I",
"it is tearing up the initial small sections. Having 2 densities of support",
"up, leaving a big mess. What appears to me to be happening, is",
"the rest of the support layer, such that when the rest of the",
"support layer per layer seems to be causing issues. Failed print, still on",
"get printed first. These layers do not touch the outer brim. They go",
"first (circled in red) are either not adhering well enough, or somehow getting",
"hand end of first picture). Then, it attempts to print the whole-of-base support",
"printer calibration, z-axis calibration, etc. Only thing that might be a bit out",
"different support structures and very minimal contact of actual object to the bed",
"up the initial small sections. Having 2 densities of support layer per layer",
"for details). Where these support layers touch the outer brim, they adhere well.",
"STL from Thingiverse, and I sliced it with Prosi Control. Settings: 0.3 mm",
"adhere well. When they touch the initial support layer sections, it tears them",
"note, why the funny diagonal line cutting through the rest of the support",
"printing first layer of an object with support. The object has a few",
"z-axis might be a *fraction* too low. I have no issues when printing",
"(which adheres well), it tries to print the support layers for the \"actual\"",
"foot print. I am printing on a genuine Prosi i3 mk2s, using PLA,",
"low. I have no issues when printing objects without support, and usually don't",
"3D printing, and having difficulty printing first layer of an object with support.",
"genuine Prosi i3 mk2s, using PLA, 210 °C (clean from what I can",
"on the right hand end of first picture). Then, it attempts to print",
"adhering well enough, or somehow getting \"ruffled up\", or are printed too close",
"layer is printed, it is tearing up the initial small sections. Having 2",
"calibration, z-axis calibration, etc. Only thing that might be a bit out is",
"layer 1](https://i.stack.imgur.com/RMFL5.png)](https://i.stack.imgur.com/RMFL5.png) Close up of other problem area in PC slicing. No actual",
"having difficulty printing first layer of an object with support. The object has",
"to print the support layers for the \"actual\" layers that will get printed",
"object to the bed (orange) [](https://i.stack.imgur.com/RMFL5.png) Close up of",
"when the printer does a 180-degree turn. (this can be seen on the",
"has a few curved surfaces that touch the print bed, so not a",
"support layer, such that when the rest of the support layer is printed,",
"initial support layer sections, it tears them up, leaving a big mess. What",
"printing, and having difficulty printing first layer of an object with support. The",
"first layer. The broad strokes seem to adhere well except for when they",
"After it prints the brim (which adheres well), it tries to print the",
"bed. My model is an STL from Thingiverse, and I sliced it with",
"well except for when they meet where the fine layer was - after",
"(clean, good condition) heat bed. My model is an STL from Thingiverse, and",
"the right, there is a section of \"fine\" support material that sort of",
"the bed. At the right, there is a section of \"fine\" support material",
"the rest of the support layer is printed, it is tearing up the",
"Prosi Control. Settings: 0.3 mm layers, 30 % infill, Support from build plate,",
"turn. (this can be seen on the right hand end of first picture).",
"to me to be happening, is the small sections that get printed first",
"was - after that it's just a big mess. [](https://i.stack.imgur.com/NKa4E.jpg) Close up of the failed first layer. The broad",
"I have run the printer calibration, z-axis calibration, etc. Only thing that might",
"go down with a little bit of \"squeeze out\" when the printer does",
"bit out is my z-axis might be a *fraction* too low. I have",
"do not touch the outer brim. They go down with a little bit",
"on. I have run the printer calibration, z-axis calibration, etc. Only thing that",
"it with Prosi Control. Settings: 0.3 mm layers, 30 % infill, Support from",
"brim, they adhere well. When they touch the initial support layer sections, it",
"sliced it with Prosi Control. Settings: 0.3 mm layers, 30 % infill, Support",
"not a big starting foot print. I am printing on a genuine Prosi",
"printed first. These layers do not touch the outer brim. They go down",
"that when the rest of the support layer is printed, it is tearing",
"diagonal line cutting through the rest of the support structure here? [![Prosi control",
"printed first (circled in red) are either not adhering well enough, or somehow",
"meet where the fine layer was - after that it's just a big",
"details). Where these support layers touch the outer brim, they adhere well. When"
] |
[
"not square to each other. I'm wondering how to adjust this - I'm",
"and when it was done there was a gap on one side when",
"well (or so I thought) and printing a number of models pretty well.",
"distance between the front and back is the same (I can't imagine why",
"side when the lid was slid on. I checked the parts and it",
"parts and it turns out they are not square - which means the",
"and the front by adjusting the threaded rods that separate them to a",
"I have an Anet A8 printer for about 4 months, set up pretty",
"about 4 months, set up pretty well (or so I thought) and printing",
"was done there was a gap on one side when the lid was",
"square to each other. I'm wondering how to adjust this - I'm thinking",
"was a gap on one side when the lid was slid on. I",
"of models pretty well. I made a large 3\" x 6\" box with",
"set up pretty well (or so I thought) and printing a number of",
"it turns out they are not square - which means the X and",
"a large 3\" x 6\" box with a sliding lid yesterday and when",
"the first things I'll check is that the distance between the front and",
"box with a sliding lid yesterday and when it was done there was",
"that extending the distance between the back of the frame and the front",
"one side when the lid was slid on. I checked the parts and",
"between the front and back is the same (I can't imagine why I",
"lid yesterday and when it was done there was a gap on one",
"a number of models pretty well. I made a large 3\" x 6\"",
"frame and the front by adjusting the threaded rods that separate them to",
"x 6\" box with a sliding lid yesterday and when it was done",
"well. I made a large 3\" x 6\" box with a sliding lid",
"between the back of the frame and the front by adjusting the threaded",
"the parts and it turns out they are not square - which means",
"printer for about 4 months, set up pretty well (or so I thought)",
"I made a large 3\" x 6\" box with a sliding lid yesterday",
"by adjusting the threaded rods that separate them to a wider distance on",
"the side where the angle is obtuse. Obviously one of the first things",
"(or so I thought) and printing a number of models pretty well. I",
"of the frame and the front by adjusting the threaded rods that separate",
"have an Anet A8 printer for about 4 months, set up pretty well",
"one of the first things I'll check is that the distance between the",
"rods that separate them to a wider distance on the side where the",
"Anet A8 printer for about 4 months, set up pretty well (or so",
"of the first things I'll check is that the distance between the front",
"angle is obtuse. Obviously one of the first things I'll check is that",
"I checked the parts and it turns out they are not square -",
"it was done there was a gap on one side when the lid",
"- I'm thinking that extending the distance between the back of the frame",
"printing a number of models pretty well. I made a large 3\" x",
"slid on. I checked the parts and it turns out they are not",
"to each other. I'm wondering how to adjust this - I'm thinking that",
"out they are not square - which means the X and Y axes",
"that separate them to a wider distance on the side where the angle",
"is that the distance between the front and back is the same (I",
"the distance between the front and back is the same (I can't imagine",
"this - I'm thinking that extending the distance between the back of the",
"check is that the distance between the front and back is the same",
"the same (I can't imagine why I never checked that before, come to",
"and back is the same (I can't imagine why I never checked that",
"thinking that extending the distance between the back of the frame and the",
"to a wider distance on the side where the angle is obtuse. Obviously",
"checked that before, come to think of it). Does this sound like a",
"are not square - which means the X and Y axes are not",
"sliding lid yesterday and when it was done there was a gap on",
"up pretty well (or so I thought) and printing a number of models",
"distance between the back of the frame and the front by adjusting the",
"is the same (I can't imagine why I never checked that before, come",
"done there was a gap on one side when the lid was slid",
"first things I'll check is that the distance between the front and back",
"- which means the X and Y axes are not square to each",
"the angle is obtuse. Obviously one of the first things I'll check is",
"not square - which means the X and Y axes are not square",
"I never checked that before, come to think of it). Does this sound",
"a wider distance on the side where the angle is obtuse. Obviously one",
"models pretty well. I made a large 3\" x 6\" box with a",
"adjusting the threaded rods that separate them to a wider distance on the",
"a gap on one side when the lid was slid on. I checked",
"I'll check is that the distance between the front and back is the",
"turns out they are not square - which means the X and Y",
"front and back is the same (I can't imagine why I never checked",
"thought) and printing a number of models pretty well. I made a large",
"why I never checked that before, come to think of it). Does this",
"a sliding lid yesterday and when it was done there was a gap",
"and it turns out they are not square - which means the X",
"Obviously one of the first things I'll check is that the distance between",
"6\" box with a sliding lid yesterday and when it was done there",
"which means the X and Y axes are not square to each other.",
"months, set up pretty well (or so I thought) and printing a number",
"pretty well (or so I thought) and printing a number of models pretty",
"side where the angle is obtuse. Obviously one of the first things I'll",
"the front and back is the same (I can't imagine why I never",
"can't imagine why I never checked that before, come to think of it).",
"checked the parts and it turns out they are not square - which",
"front by adjusting the threaded rods that separate them to a wider distance",
"are not square to each other. I'm wondering how to adjust this -",
"pretty well. I made a large 3\" x 6\" box with a sliding",
"the X and Y axes are not square to each other. I'm wondering",
"when it was done there was a gap on one side when the",
"X and Y axes are not square to each other. I'm wondering how",
"other. I'm wondering how to adjust this - I'm thinking that extending the",
"yesterday and when it was done there was a gap on one side",
"with a sliding lid yesterday and when it was done there was a",
"an Anet A8 printer for about 4 months, set up pretty well (or",
"the frame and the front by adjusting the threaded rods that separate them",
"large 3\" x 6\" box with a sliding lid yesterday and when it",
"they are not square - which means the X and Y axes are",
"where the angle is obtuse. Obviously one of the first things I'll check",
"when the lid was slid on. I checked the parts and it turns",
"distance on the side where the angle is obtuse. Obviously one of the",
"4 months, set up pretty well (or so I thought) and printing a",
"imagine why I never checked that before, come to think of it). Does",
"adjust this - I'm thinking that extending the distance between the back of",
"that before, come to think of it). Does this sound like a sound",
"number of models pretty well. I made a large 3\" x 6\" box",
"axes are not square to each other. I'm wondering how to adjust this",
"the distance between the back of the frame and the front by adjusting",
"and Y axes are not square to each other. I'm wondering how to",
"so I thought) and printing a number of models pretty well. I made",
"made a large 3\" x 6\" box with a sliding lid yesterday and",
"3\" x 6\" box with a sliding lid yesterday and when it was",
"them to a wider distance on the side where the angle is obtuse.",
"the back of the frame and the front by adjusting the threaded rods",
"the threaded rods that separate them to a wider distance on the side",
"on. I checked the parts and it turns out they are not square",
"never checked that before, come to think of it). Does this sound like",
"on the side where the angle is obtuse. Obviously one of the first",
"wider distance on the side where the angle is obtuse. Obviously one of",
"means the X and Y axes are not square to each other. I'm",
"the lid was slid on. I checked the parts and it turns out",
"I thought) and printing a number of models pretty well. I made a",
"that the distance between the front and back is the same (I can't",
"before, come to think of it). Does this sound like a sound plan?",
"things I'll check is that the distance between the front and back is",
"obtuse. Obviously one of the first things I'll check is that the distance",
"A8 printer for about 4 months, set up pretty well (or so I",
"was slid on. I checked the parts and it turns out they are",
"square - which means the X and Y axes are not square to",
"same (I can't imagine why I never checked that before, come to think",
"wondering how to adjust this - I'm thinking that extending the distance between",
"gap on one side when the lid was slid on. I checked the",
"how to adjust this - I'm thinking that extending the distance between the",
"Y axes are not square to each other. I'm wondering how to adjust",
"and printing a number of models pretty well. I made a large 3\"",
"extending the distance between the back of the frame and the front by",
"each other. I'm wondering how to adjust this - I'm thinking that extending",
"for about 4 months, set up pretty well (or so I thought) and",
"there was a gap on one side when the lid was slid on.",
"to adjust this - I'm thinking that extending the distance between the back",
"I'm wondering how to adjust this - I'm thinking that extending the distance",
"back is the same (I can't imagine why I never checked that before,",
"I'm thinking that extending the distance between the back of the frame and",
"(I can't imagine why I never checked that before, come to think of",
"the front by adjusting the threaded rods that separate them to a wider",
"on one side when the lid was slid on. I checked the parts",
"back of the frame and the front by adjusting the threaded rods that",
"threaded rods that separate them to a wider distance on the side where",
"is obtuse. Obviously one of the first things I'll check is that the",
"lid was slid on. I checked the parts and it turns out they",
"separate them to a wider distance on the side where the angle is"
] |
[
"protopasta The conductive pla is not that strong, so when I take my",
"do to themselves (unlike PLA) What’s a good way to remove a conductive",
"the board * using no skirt does not work, as the printer clogs",
"and after dumping a bunch of acetone on the board * using no",
"bot metal with a heated bed, the heated bed I am not using.",
"pieces only chip, because they stick better to the bed than they do",
"no matter what I try * a razor blade does not work, even",
"printer bot metal with a heated bed, the heated bed I am not",
"does not work, even when the bed isn’t heated and after dumping a",
"simple printer bot metal with a heated bed, the heated bed I am",
"conductive pla by protopasta The conductive pla is not that strong, so when",
"point that printing itself isn’t fun * when scratching it off, the pieces",
"matter what I try * a razor blade does not work, even when",
"bed plate! I cannot get the skirt off the bed plate, no matter",
"using conductive pla by protopasta The conductive pla is not that strong, so",
"of the beds? The skirt is the initial outline a printer lays down,",
"to the point that printing itself isn’t fun * when scratching it off,",
"sometimes they break. The only time it appears to be invincibly strong is",
"* a razor blade does not work, even when the bed isn’t heated",
"it sticks to the bed plate! I cannot get the skirt off the",
"I cannot get the skirt off the bed plate, no matter what I",
"dumping a bunch of acetone on the board * using no skirt does",
"The skirt is the initial outline a printer lays down, it is very",
"the heated bed I am not using. I am using conductive pla by",
"bed isn’t heated and after dumping a bunch of acetone on the board",
"on the board * using no skirt does not work, as the printer",
"bed than they do to themselves (unlike PLA) What’s a good way to",
"from one of the beds? The skirt is the initial outline a printer",
"bunch of acetone on the board * using no skirt does not work,",
"* it is difficult enough to remove to the point that printing itself",
"strong, so when I take my pieces off the board, sometimes they break.",
"work, as the printer clogs itself * it is difficult enough to remove",
"to be invincibly strong is when it sticks to the bed plate! I",
"skirt does not work, as the printer clogs itself * it is difficult",
"conductive pla skirt from one of the beds? The skirt is the initial",
"pla by protopasta The conductive pla is not that strong, so when I",
"itself * it is difficult enough to remove to the point that printing",
"the beds? The skirt is the initial outline a printer lays down, it",
"difficult enough to remove to the point that printing itself isn’t fun *",
"printer clogs itself * it is difficult enough to remove to the point",
"PLA) What’s a good way to remove a conductive pla skirt from one",
"the printer clogs itself * it is difficult enough to remove to the",
"stick better to the bed than they do to themselves (unlike PLA) What’s",
"by protopasta The conductive pla is not that strong, so when I take",
"remove to the point that printing itself isn’t fun * when scratching it",
"way to remove a conductive pla skirt from one of the beds? The",
"my pieces off the board, sometimes they break. The only time it appears",
"the point that printing itself isn’t fun * when scratching it off, the",
"using no skirt does not work, as the printer clogs itself * it",
"board * using no skirt does not work, as the printer clogs itself",
"to the bed plate! I cannot get the skirt off the bed plate,",
"off, the pieces only chip, because they stick better to the bed than",
"a good way to remove a conductive pla skirt from one of the",
"pla is not that strong, so when I take my pieces off the",
"time it appears to be invincibly strong is when it sticks to the",
"what I try * a razor blade does not work, even when the",
"not work, as the printer clogs itself * it is difficult enough to",
"only chip, because they stick better to the bed than they do to",
"to the bed than they do to themselves (unlike PLA) What’s a good",
"even when the bed isn’t heated and after dumping a bunch of acetone",
"they break. The only time it appears to be invincibly strong is when",
"a simple printer bot metal with a heated bed, the heated bed I",
"board, sometimes they break. The only time it appears to be invincibly strong",
"skirt from one of the beds? The skirt is the initial outline a",
"(unlike PLA) What’s a good way to remove a conductive pla skirt from",
"the bed plate! I cannot get the skirt off the bed plate, no",
"am not using. I am using conductive pla by protopasta The conductive pla",
"the board, sometimes they break. The only time it appears to be invincibly",
"to remove a conductive pla skirt from one of the beds? The skirt",
"is when it sticks to the bed plate! I cannot get the skirt",
"What’s a good way to remove a conductive pla skirt from one of",
"heated bed I am not using. I am using conductive pla by protopasta",
"break. The only time it appears to be invincibly strong is when it",
"am using conductive pla by protopasta The conductive pla is not that strong,",
"so when I take my pieces off the board, sometimes they break. The",
"the bed than they do to themselves (unlike PLA) What’s a good way",
"no skirt does not work, as the printer clogs itself * it is",
"plate! I cannot get the skirt off the bed plate, no matter what",
"not using. I am using conductive pla by protopasta The conductive pla is",
"try * a razor blade does not work, even when the bed isn’t",
"to themselves (unlike PLA) What’s a good way to remove a conductive pla",
"using. I am using conductive pla by protopasta The conductive pla is not",
"get the skirt off the bed plate, no matter what I try *",
"a bunch of acetone on the board * using no skirt does not",
"blade does not work, even when the bed isn’t heated and after dumping",
"conductive pla is not that strong, so when I take my pieces off",
"as the printer clogs itself * it is difficult enough to remove to",
"is not that strong, so when I take my pieces off the board,",
"because they stick better to the bed than they do to themselves (unlike",
"clogs itself * it is difficult enough to remove to the point that",
"bed plate, no matter what I try * a razor blade does not",
"they do to themselves (unlike PLA) What’s a good way to remove a",
"the pieces only chip, because they stick better to the bed than they",
"heated and after dumping a bunch of acetone on the board * using",
"it off, the pieces only chip, because they stick better to the bed",
"itself isn’t fun * when scratching it off, the pieces only chip, because",
"the bed isn’t heated and after dumping a bunch of acetone on the",
"a razor blade does not work, even when the bed isn’t heated and",
"The only time it appears to be invincibly strong is when it sticks",
"chip, because they stick better to the bed than they do to themselves",
"when the bed isn’t heated and after dumping a bunch of acetone on",
"good way to remove a conductive pla skirt from one of the beds?",
"* when scratching it off, the pieces only chip, because they stick better",
"when scratching it off, the pieces only chip, because they stick better to",
"I have a simple printer bot metal with a heated bed, the heated",
"razor blade does not work, even when the bed isn’t heated and after",
"skirt is the initial outline a printer lays down, it is very thin",
"beds? The skirt is the initial outline a printer lays down, it is",
"the skirt off the bed plate, no matter what I try * a",
"with a heated bed, the heated bed I am not using. I am",
"have a simple printer bot metal with a heated bed, the heated bed",
"heated bed, the heated bed I am not using. I am using conductive",
"strong is when it sticks to the bed plate! I cannot get the",
"themselves (unlike PLA) What’s a good way to remove a conductive pla skirt",
"I am not using. I am using conductive pla by protopasta The conductive",
"better to the bed than they do to themselves (unlike PLA) What’s a",
"isn’t heated and after dumping a bunch of acetone on the board *",
"scratching it off, the pieces only chip, because they stick better to the",
"one of the beds? The skirt is the initial outline a printer lays",
"is difficult enough to remove to the point that printing itself isn’t fun",
"of acetone on the board * using no skirt does not work, as",
"sticks to the bed plate! I cannot get the skirt off the bed",
"cannot get the skirt off the bed plate, no matter what I try",
"does not work, as the printer clogs itself * it is difficult enough",
"to remove to the point that printing itself isn’t fun * when scratching",
"bed I am not using. I am using conductive pla by protopasta The",
"skirt off the bed plate, no matter what I try * a razor",
"fun * when scratching it off, the pieces only chip, because they stick",
"I take my pieces off the board, sometimes they break. The only time",
"after dumping a bunch of acetone on the board * using no skirt",
"off the board, sometimes they break. The only time it appears to be",
"it appears to be invincibly strong is when it sticks to the bed",
"a heated bed, the heated bed I am not using. I am using",
"work, even when the bed isn’t heated and after dumping a bunch of",
"only time it appears to be invincibly strong is when it sticks to",
"it is difficult enough to remove to the point that printing itself isn’t",
"isn’t fun * when scratching it off, the pieces only chip, because they",
"printing itself isn’t fun * when scratching it off, the pieces only chip,",
"* using no skirt does not work, as the printer clogs itself *",
"a conductive pla skirt from one of the beds? The skirt is the",
"that printing itself isn’t fun * when scratching it off, the pieces only",
"when I take my pieces off the board, sometimes they break. The only",
"pieces off the board, sometimes they break. The only time it appears to",
"than they do to themselves (unlike PLA) What’s a good way to remove",
"be invincibly strong is when it sticks to the bed plate! I cannot",
"I try * a razor blade does not work, even when the bed",
"remove a conductive pla skirt from one of the beds? The skirt is",
"they stick better to the bed than they do to themselves (unlike PLA)",
"enough to remove to the point that printing itself isn’t fun * when",
"off the bed plate, no matter what I try * a razor blade",
"invincibly strong is when it sticks to the bed plate! I cannot get",
"the bed plate, no matter what I try * a razor blade does",
"take my pieces off the board, sometimes they break. The only time it",
"appears to be invincibly strong is when it sticks to the bed plate!",
"bed, the heated bed I am not using. I am using conductive pla",
"that strong, so when I take my pieces off the board, sometimes they",
"pla skirt from one of the beds? The skirt is the initial outline",
"acetone on the board * using no skirt does not work, as the",
"not work, even when the bed isn’t heated and after dumping a bunch",
"plate, no matter what I try * a razor blade does not work,",
"not that strong, so when I take my pieces off the board, sometimes",
"when it sticks to the bed plate! I cannot get the skirt off",
"I am using conductive pla by protopasta The conductive pla is not that",
"metal with a heated bed, the heated bed I am not using. I",
"The conductive pla is not that strong, so when I take my pieces"
] |
[
"z-point of 4 mm or below. Is there a software that will enable",
"a need to only offer support for overhangs up to a certain z",
"will enable this, either as a setting/addition to Ultimaker Cura or just a",
"hanging over the build plate. I have a need to only offer support",
"only offer support for overhangs up to a certain z height, such any",
"Cura offers a platform support type of “*touching buildplate*” which enables the printer",
"only make a raft for parts of the object that should be touching",
"offer support for overhangs up to a certain z height, such any overhang",
"to a certain z height, such any overhang located at a z-point of",
"below. Is there a software that will enable this, either as a setting/addition",
"a z-point of 4 mm or below. Is there a software that will",
"“*touching buildplate*” which enables the printer to only make a raft for parts",
"of 4 mm or below. Is there a software that will enable this,",
"plate. I have a need to only offer support for overhangs up to",
"of the object that should be touching the build plate. It also offers",
"also offers “*everywhere*” for any object that might be hanging over the build",
"object that might be hanging over the build plate. I have a need",
"enables the printer to only make a raft for parts of the object",
"printer to only make a raft for parts of the object that should",
"offers a platform support type of “*touching buildplate*” which enables the printer to",
"be hanging over the build plate. I have a need to only offer",
"at a z-point of 4 mm or below. Is there a software that",
"for overhangs up to a certain z height, such any overhang located at",
"a raft for parts of the object that should be touching the build",
"the printer to only make a raft for parts of the object that",
"which enables the printer to only make a raft for parts of the",
"overhangs up to a certain z height, such any overhang located at a",
"raft for parts of the object that should be touching the build plate.",
"the build plate. I have a need to only offer support for overhangs",
"a platform support type of “*touching buildplate*” which enables the printer to only",
"or below. Is there a software that will enable this, either as a",
"object that should be touching the build plate. It also offers “*everywhere*” for",
"to only offer support for overhangs up to a certain z height, such",
"as a setting/addition to Ultimaker Cura or just a G-code export for Pronterface?",
"support type of “*touching buildplate*” which enables the printer to only make a",
"to only make a raft for parts of the object that should be",
"that might be hanging over the build plate. I have a need to",
"build plate. It also offers “*everywhere*” for any object that might be hanging",
"up to a certain z height, such any overhang located at a z-point",
"a certain z height, such any overhang located at a z-point of 4",
"that will enable this, either as a setting/addition to Ultimaker Cura or just",
"software that will enable this, either as a setting/addition to Ultimaker Cura or",
"parts of the object that should be touching the build plate. It also",
"Ultimaker Cura offers a platform support type of “*touching buildplate*” which enables the",
"overhang located at a z-point of 4 mm or below. Is there a",
"4 mm or below. Is there a software that will enable this, either",
"build plate. I have a need to only offer support for overhangs up",
"this, either as a setting/addition to Ultimaker Cura or just a G-code export",
"certain z height, such any overhang located at a z-point of 4 mm",
"need to only offer support for overhangs up to a certain z height,",
"type of “*touching buildplate*” which enables the printer to only make a raft",
"the build plate. It also offers “*everywhere*” for any object that might be",
"enable this, either as a setting/addition to Ultimaker Cura or just a G-code",
"located at a z-point of 4 mm or below. Is there a software",
"over the build plate. I have a need to only offer support for",
"for parts of the object that should be touching the build plate. It",
"such any overhang located at a z-point of 4 mm or below. Is",
"of “*touching buildplate*” which enables the printer to only make a raft for",
"platform support type of “*touching buildplate*” which enables the printer to only make",
"make a raft for parts of the object that should be touching the",
"for any object that might be hanging over the build plate. I have",
"support for overhangs up to a certain z height, such any overhang located",
"a software that will enable this, either as a setting/addition to Ultimaker Cura",
"might be hanging over the build plate. I have a need to only",
"any overhang located at a z-point of 4 mm or below. Is there",
"there a software that will enable this, either as a setting/addition to Ultimaker",
"It also offers “*everywhere*” for any object that might be hanging over the",
"touching the build plate. It also offers “*everywhere*” for any object that might",
"be touching the build plate. It also offers “*everywhere*” for any object that",
"any object that might be hanging over the build plate. I have a",
"have a need to only offer support for overhangs up to a certain",
"z height, such any overhang located at a z-point of 4 mm or",
"“*everywhere*” for any object that might be hanging over the build plate. I",
"mm or below. Is there a software that will enable this, either as",
"should be touching the build plate. It also offers “*everywhere*” for any object",
"plate. It also offers “*everywhere*” for any object that might be hanging over",
"offers “*everywhere*” for any object that might be hanging over the build plate.",
"Is there a software that will enable this, either as a setting/addition to",
"height, such any overhang located at a z-point of 4 mm or below.",
"buildplate*” which enables the printer to only make a raft for parts of",
"that should be touching the build plate. It also offers “*everywhere*” for any",
"the object that should be touching the build plate. It also offers “*everywhere*”",
"either as a setting/addition to Ultimaker Cura or just a G-code export for",
"I have a need to only offer support for overhangs up to a"
] |
[
"3d printer you **could** use/do the following: * Create G-code using a program",
"arduino uno shield. * The drivers will control the steppers. If you want",
"the instructions to the drivers through a GRBL arduino uno shield. * The",
"(GRBL). * Pass it into an Arduino with GRBL. * The arduino can",
"work properly? Is there an existing open source software for delta printers/cncs? EDIT:",
"drivers will control the steppers. If you want to make a DYI delta",
"to work properly? Is there an existing open source software for delta printers/cncs?",
"existing open source software for delta printers/cncs? EDIT: This question could be asked",
"G-code Sender (GRBL). * Pass it into an Arduino with GRBL. * The",
"uno shield. * The drivers will control the steppers. If you want to",
"This question could be asked about any kind of non-cartesian 3d printer, including",
"DIY cartesian 3d printer you **could** use/do the following: * Create G-code using",
"G-code using a program of your choice. * Load it into Universal G-code",
"through a GRBL arduino uno shield. * The drivers will control the steppers.",
"point of this whole process needs to be altered in order for the",
"for the delta printer to work properly? Is there an existing open source",
"it into Universal G-code Sender (GRBL). * Pass it into an Arduino with",
"a GRBL arduino uno shield. * The drivers will control the steppers. If",
"make a DIY cartesian 3d printer you **could** use/do the following: * Create",
"be altered in order for the delta printer to work properly? Is there",
"of your choice. * Load it into Universal G-code Sender (GRBL). * Pass",
"The arduino can pass the instructions to the drivers through a GRBL arduino",
"asked about any kind of non-cartesian 3d printer, including Delta, SCARA, Polar, etc.",
"altered in order for the delta printer to work properly? Is there an",
"it into an Arduino with GRBL. * The arduino can pass the instructions",
"a program of your choice. * Load it into Universal G-code Sender (GRBL).",
"printer, which point of this whole process needs to be altered in order",
"drivers through a GRBL arduino uno shield. * The drivers will control the",
"pass the instructions to the drivers through a GRBL arduino uno shield. *",
"the steppers. If you want to make a DYI delta 3d printer, which",
"* The arduino can pass the instructions to the drivers through a GRBL",
"a DIY cartesian 3d printer you **could** use/do the following: * Create G-code",
"the drivers through a GRBL arduino uno shield. * The drivers will control",
"* The drivers will control the steppers. If you want to make a",
"you want to make a DYI delta 3d printer, which point of this",
"**could** use/do the following: * Create G-code using a program of your choice.",
"GRBL. * The arduino can pass the instructions to the drivers through a",
"instructions to the drivers through a GRBL arduino uno shield. * The drivers",
"with GRBL. * The arduino can pass the instructions to the drivers through",
"can pass the instructions to the drivers through a GRBL arduino uno shield.",
"an Arduino with GRBL. * The arduino can pass the instructions to the",
"shield. * The drivers will control the steppers. If you want to make",
"of this whole process needs to be altered in order for the delta",
"3d printer, which point of this whole process needs to be altered in",
"process needs to be altered in order for the delta printer to work",
"delta printers/cncs? EDIT: This question could be asked about any kind of non-cartesian",
"steppers. If you want to make a DYI delta 3d printer, which point",
"to make a DIY cartesian 3d printer you **could** use/do the following: *",
"delta 3d printer, which point of this whole process needs to be altered",
"you **could** use/do the following: * Create G-code using a program of your",
"this whole process needs to be altered in order for the delta printer",
"choice. * Load it into Universal G-code Sender (GRBL). * Pass it into",
"source software for delta printers/cncs? EDIT: This question could be asked about any",
"into Universal G-code Sender (GRBL). * Pass it into an Arduino with GRBL.",
"into an Arduino with GRBL. * The arduino can pass the instructions to",
"arduino can pass the instructions to the drivers through a GRBL arduino uno",
"Pass it into an Arduino with GRBL. * The arduino can pass the",
"will control the steppers. If you want to make a DYI delta 3d",
"the following: * Create G-code using a program of your choice. * Load",
"* Pass it into an Arduino with GRBL. * The arduino can pass",
"to the drivers through a GRBL arduino uno shield. * The drivers will",
"a DYI delta 3d printer, which point of this whole process needs to",
"want to make a DYI delta 3d printer, which point of this whole",
"delta printer to work properly? Is there an existing open source software for",
"for delta printers/cncs? EDIT: This question could be asked about any kind of",
"* Create G-code using a program of your choice. * Load it into",
"printers/cncs? EDIT: This question could be asked about any kind of non-cartesian 3d",
"make a DYI delta 3d printer, which point of this whole process needs",
"program of your choice. * Load it into Universal G-code Sender (GRBL). *",
"The drivers will control the steppers. If you want to make a DYI",
"there an existing open source software for delta printers/cncs? EDIT: This question could",
"to be altered in order for the delta printer to work properly? Is",
"* Load it into Universal G-code Sender (GRBL). * Pass it into an",
"could be asked about any kind of non-cartesian 3d printer, including Delta, SCARA,",
"DYI delta 3d printer, which point of this whole process needs to be",
"software for delta printers/cncs? EDIT: This question could be asked about any kind",
"EDIT: This question could be asked about any kind of non-cartesian 3d printer,",
"properly? Is there an existing open source software for delta printers/cncs? EDIT: This",
"example, to make a DIY cartesian 3d printer you **could** use/do the following:",
"following: * Create G-code using a program of your choice. * Load it",
"which point of this whole process needs to be altered in order for",
"printer to work properly? Is there an existing open source software for delta",
"question could be asked about any kind of non-cartesian 3d printer, including Delta,",
"open source software for delta printers/cncs? EDIT: This question could be asked about",
"needs to be altered in order for the delta printer to work properly?",
"using a program of your choice. * Load it into Universal G-code Sender",
"Sender (GRBL). * Pass it into an Arduino with GRBL. * The arduino",
"whole process needs to be altered in order for the delta printer to",
"Universal G-code Sender (GRBL). * Pass it into an Arduino with GRBL. *",
"Is there an existing open source software for delta printers/cncs? EDIT: This question",
"Arduino with GRBL. * The arduino can pass the instructions to the drivers",
"For example, to make a DIY cartesian 3d printer you **could** use/do the",
"order for the delta printer to work properly? Is there an existing open",
"an existing open source software for delta printers/cncs? EDIT: This question could be",
"GRBL arduino uno shield. * The drivers will control the steppers. If you",
"Create G-code using a program of your choice. * Load it into Universal",
"to make a DYI delta 3d printer, which point of this whole process",
"in order for the delta printer to work properly? Is there an existing",
"cartesian 3d printer you **could** use/do the following: * Create G-code using a",
"use/do the following: * Create G-code using a program of your choice. *",
"If you want to make a DYI delta 3d printer, which point of",
"Load it into Universal G-code Sender (GRBL). * Pass it into an Arduino",
"the delta printer to work properly? Is there an existing open source software",
"control the steppers. If you want to make a DYI delta 3d printer,",
"be asked about any kind of non-cartesian 3d printer, including Delta, SCARA, Polar,",
"your choice. * Load it into Universal G-code Sender (GRBL). * Pass it",
"printer you **could** use/do the following: * Create G-code using a program of"
] |
[
"Creaform3D EXAscan laying around at the company I work for, and tried to",
"but its license is expired. I looked in the manufacturer site for drivers",
"if it still works. I discovered that it uses a software called RapidForm",
"Is there any other software or way to read the data coming from",
"for data acquisition, but its license is expired. I looked in the manufacturer",
"something similar but there isn't anything. Is there any other software or way",
"I discovered that it uses a software called RapidForm for data acquisition, but",
"for drivers or something similar but there isn't anything. Is there any other",
"I work for, and tried to plug it on a computer to see",
"laying around at the company I work for, and tried to plug it",
"old Creaform3D EXAscan laying around at the company I work for, and tried",
"or something similar but there isn't anything. Is there any other software or",
"found an old Creaform3D EXAscan laying around at the company I work for,",
"a computer to see if it still works. I discovered that it uses",
"an old Creaform3D EXAscan laying around at the company I work for, and",
"uses a software called RapidForm for data acquisition, but its license is expired.",
"RapidForm for data acquisition, but its license is expired. I looked in the",
"a software called RapidForm for data acquisition, but its license is expired. I",
"I found an old Creaform3D EXAscan laying around at the company I work",
"to plug it on a computer to see if it still works. I",
"it on a computer to see if it still works. I discovered that",
"data acquisition, but its license is expired. I looked in the manufacturer site",
"discovered that it uses a software called RapidForm for data acquisition, but its",
"still works. I discovered that it uses a software called RapidForm for data",
"on a computer to see if it still works. I discovered that it",
"license is expired. I looked in the manufacturer site for drivers or something",
"any other software or way to read the data coming from such scanner?",
"is expired. I looked in the manufacturer site for drivers or something similar",
"software called RapidForm for data acquisition, but its license is expired. I looked",
"site for drivers or something similar but there isn't anything. Is there any",
"drivers or something similar but there isn't anything. Is there any other software",
"acquisition, but its license is expired. I looked in the manufacturer site for",
"around at the company I work for, and tried to plug it on",
"see if it still works. I discovered that it uses a software called",
"its license is expired. I looked in the manufacturer site for drivers or",
"expired. I looked in the manufacturer site for drivers or something similar but",
"it uses a software called RapidForm for data acquisition, but its license is",
"similar but there isn't anything. Is there any other software or way to",
"tried to plug it on a computer to see if it still works.",
"looked in the manufacturer site for drivers or something similar but there isn't",
"but there isn't anything. Is there any other software or way to read",
"company I work for, and tried to plug it on a computer to",
"manufacturer site for drivers or something similar but there isn't anything. Is there",
"there isn't anything. Is there any other software or way to read the",
"at the company I work for, and tried to plug it on a",
"isn't anything. Is there any other software or way to read the data",
"the company I work for, and tried to plug it on a computer",
"to see if it still works. I discovered that it uses a software",
"anything. Is there any other software or way to read the data coming",
"there any other software or way to read the data coming from such",
"that it uses a software called RapidForm for data acquisition, but its license",
"works. I discovered that it uses a software called RapidForm for data acquisition,",
"I looked in the manufacturer site for drivers or something similar but there",
"and tried to plug it on a computer to see if it still",
"in the manufacturer site for drivers or something similar but there isn't anything.",
"plug it on a computer to see if it still works. I discovered",
"computer to see if it still works. I discovered that it uses a",
"it still works. I discovered that it uses a software called RapidForm for",
"the manufacturer site for drivers or something similar but there isn't anything. Is",
"called RapidForm for data acquisition, but its license is expired. I looked in",
"for, and tried to plug it on a computer to see if it",
"EXAscan laying around at the company I work for, and tried to plug",
"work for, and tried to plug it on a computer to see if"
] |
[
"is. Could I have some help finding the thread type and what hardened",
"I have some help finding the thread type and what hardened nozzles would",
"in the dark filament, but I know that eats up brass nozzles fast.",
"nozzles fast. But there is so many thread differences so I don't know",
"get some hardened nozzles because I would love to print with some glow",
"have some help finding the thread type and what hardened nozzles would be",
"some help finding the thread type and what hardened nozzles would be recommended?",
"know that eats up brass nozzles fast. But there is so many thread",
"I want to get some hardened nozzles because I would love to print",
"the dark filament, but I know that eats up brass nozzles fast. But",
"I know what nozzle to get for my Anet A6 printer? I want",
"to get some hardened nozzles because I would love to print with some",
"eats up brass nozzles fast. But there is so many thread differences so",
"is so many thread differences so I don't know which one to get,",
"thread differences so I don't know which one to get, or even what",
"But there is so many thread differences so I don't know which one",
"so I don't know which one to get, or even what thread the",
"A6 is. Could I have some help finding the thread type and what",
"want to get some hardened nozzles because I would love to print with",
"printer? I want to get some hardened nozzles because I would love to",
"many thread differences so I don't know which one to get, or even",
"I don't know which one to get, or even what thread the Anet",
"get for my Anet A6 printer? I want to get some hardened nozzles",
"nozzles because I would love to print with some glow in the dark",
"that eats up brass nozzles fast. But there is so many thread differences",
"nozzle to get for my Anet A6 printer? I want to get some",
"but I know that eats up brass nozzles fast. But there is so",
"know which one to get, or even what thread the Anet A6 is.",
"one to get, or even what thread the Anet A6 is. Could I",
"print with some glow in the dark filament, but I know that eats",
"with some glow in the dark filament, but I know that eats up",
"filament, but I know that eats up brass nozzles fast. But there is",
"which one to get, or even what thread the Anet A6 is. Could",
"the Anet A6 is. Could I have some help finding the thread type",
"Anet A6 is. Could I have some help finding the thread type and",
"to get, or even what thread the Anet A6 is. Could I have",
"A6 printer? I want to get some hardened nozzles because I would love",
"so many thread differences so I don't know which one to get, or",
"get, or even what thread the Anet A6 is. Could I have some",
"because I would love to print with some glow in the dark filament,",
"dark filament, but I know that eats up brass nozzles fast. But there",
"I would love to print with some glow in the dark filament, but",
"fast. But there is so many thread differences so I don't know which",
"know what nozzle to get for my Anet A6 printer? I want to",
"Anet A6 printer? I want to get some hardened nozzles because I would",
"for my Anet A6 printer? I want to get some hardened nozzles because",
"what thread the Anet A6 is. Could I have some help finding the",
"love to print with some glow in the dark filament, but I know",
"what nozzle to get for my Anet A6 printer? I want to get",
"to print with some glow in the dark filament, but I know that",
"up brass nozzles fast. But there is so many thread differences so I",
"would love to print with some glow in the dark filament, but I",
"glow in the dark filament, but I know that eats up brass nozzles",
"thread the Anet A6 is. Could I have some help finding the thread",
"hardened nozzles because I would love to print with some glow in the",
"my Anet A6 printer? I want to get some hardened nozzles because I",
"some glow in the dark filament, but I know that eats up brass",
"there is so many thread differences so I don't know which one to",
"don't know which one to get, or even what thread the Anet A6",
"differences so I don't know which one to get, or even what thread",
"do I know what nozzle to get for my Anet A6 printer? I",
"Could I have some help finding the thread type and what hardened nozzles",
"or even what thread the Anet A6 is. Could I have some help",
"How do I know what nozzle to get for my Anet A6 printer?",
"brass nozzles fast. But there is so many thread differences so I don't",
"even what thread the Anet A6 is. Could I have some help finding",
"to get for my Anet A6 printer? I want to get some hardened",
"some hardened nozzles because I would love to print with some glow in",
"I know that eats up brass nozzles fast. But there is so many"
] |
[
"with removing finished prints, but not all printers have them! * Is this",
"nice to have or must have feature? * Are there any downsides to",
"them! * Is this a nice to have or must have feature? *",
"to have or must have feature? * Are there any downsides to heated",
"heated beds can help with removing finished prints, but not all printers have",
"I hear that heated beds can help with removing finished prints, but not",
"but not all printers have them! * Is this a nice to have",
"not all printers have them! * Is this a nice to have or",
"Is this a nice to have or must have feature? * Are there",
"all printers have them! * Is this a nice to have or must",
"* Is this a nice to have or must have feature? * Are",
"beds can help with removing finished prints, but not all printers have them!",
"help with removing finished prints, but not all printers have them! * Is",
"this a nice to have or must have feature? * Are there any",
"printers have them! * Is this a nice to have or must have",
"removing finished prints, but not all printers have them! * Is this a",
"have or must have feature? * Are there any downsides to heated beds?",
"hear that heated beds can help with removing finished prints, but not all",
"finished prints, but not all printers have them! * Is this a nice",
"a nice to have or must have feature? * Are there any downsides",
"that heated beds can help with removing finished prints, but not all printers",
"prints, but not all printers have them! * Is this a nice to",
"have them! * Is this a nice to have or must have feature?",
"can help with removing finished prints, but not all printers have them! *"
] |
[
"board to the computer. Can I plug external power supply and USB connection",
"not using any hotbed or anything else other than the two stepper motors",
"the RAMPS board. When powered on, can I plug the USB to my",
"the USB to my computer? Suppose I have connected two motors on the",
"When powered on, can I plug the USB to my computer? Suppose I",
"two stepper motors for the x and y axes. I am feeding 11.9",
"two motors on the X and Y outputs of the RAMPS, and the",
"to the computer at the same time? ### Additional info from comments I",
"am using RAMPS 1.4 with Polulo red stepper drivers and Arduino Mega R3.",
"or anything else other than the two stepper motors for the x and",
"external power supply is on, then can I connect my Arduino to my",
"is on, then can I connect my Arduino to my PC using USB?",
"Arduino to my PC using USB? Will it burn my board or not?",
"and RAMPS 1.4. But, somehow I burned the Arduino while I was connecting",
"else other than the two stepper motors for the x and y axes.",
"is that when the board is on load, connecting the USB to computer",
"the Arduino while I was connecting the motor and plugging the board to",
"I plug the USB to my computer? Suppose I have connected two motors",
"x and y axes. I am feeding 11.9 V supply to the RAMPS",
"with Polulo red stepper drivers and Arduino Mega R3. I am only using",
"the USB to computer motors would take power by Arduino pins instead of",
"USB? Will it burn my board or not? My only trouble is that",
"I plug external power supply and USB connection to the computer at the",
"it burn my board or not? My only trouble is that when the",
"can I connect my Arduino to my PC using USB? Will it burn",
"11.9 V supply to the RAMPS board. When powered on, can I plug",
"and not using any hotbed or anything else other than the two stepper",
"have connected two motors on the X and Y outputs of the RAMPS,",
"my Arduino to my PC using USB? Will it burn my board or",
"or not? My only trouble is that when the board is on load,",
"my PC using USB? Will it burn my board or not? My only",
"to my PC using USB? Will it burn my board or not? My",
"the same time? ### Additional info from comments I am using RAMPS 1.4",
"supply and USB connection to the computer at the same time? ### Additional",
"PC using USB? Will it burn my board or not? My only trouble",
"am feeding 11.9 V supply to the RAMPS board. When powered on, can",
"Additional info from comments I am using RAMPS 1.4 with Polulo red stepper",
"want to run two stepper motors using Arduino Mega 2560 and RAMPS 1.4.",
"1.4. But, somehow I burned the Arduino while I was connecting the motor",
"the external power supply is on, then can I connect my Arduino to",
"outputs of the RAMPS, and the external power supply is on, then can",
"any hotbed or anything else other than the two stepper motors for the",
"my computer? Suppose I have connected two motors on the X and Y",
"board. When powered on, can I plug the USB to my computer? Suppose",
"stepper drivers and Arduino Mega R3. I am only using two Nema 17",
"Nema 17 stepper motors and not using any hotbed or anything else other",
"trouble is that when the board is on load, connecting the USB to",
"when the board is on load, connecting the USB to computer motors would",
"R3. I am only using two Nema 17 stepper motors and not using",
"to my computer? Suppose I have connected two motors on the X and",
"I was connecting the motor and plugging the board to the computer. Can",
"Polulo red stepper drivers and Arduino Mega R3. I am only using two",
"board is on load, connecting the USB to computer motors would take power",
"I am using RAMPS 1.4 with Polulo red stepper drivers and Arduino Mega",
"motors on the X and Y outputs of the RAMPS, and the external",
"other than the two stepper motors for the x and y axes. I",
"the board to the computer. Can I plug external power supply and USB",
"burned the Arduino while I was connecting the motor and plugging the board",
"info from comments I am using RAMPS 1.4 with Polulo red stepper drivers",
"to computer motors would take power by Arduino pins instead of the RAMPS",
"RAMPS 1.4 with Polulo red stepper drivers and Arduino Mega R3. I am",
"for the x and y axes. I am feeding 11.9 V supply to",
"same time? ### Additional info from comments I am using RAMPS 1.4 with",
"load, connecting the USB to computer motors would take power by Arduino pins",
"red stepper drivers and Arduino Mega R3. I am only using two Nema",
"connecting the motor and plugging the board to the computer. Can I plug",
"and Y outputs of the RAMPS, and the external power supply is on,",
"stepper motors for the x and y axes. I am feeding 11.9 V",
"the computer. Can I plug external power supply and USB connection to the",
"the board is on load, connecting the USB to computer motors would take",
"connection to the computer at the same time? ### Additional info from comments",
"to the RAMPS board. When powered on, can I plug the USB to",
"from comments I am using RAMPS 1.4 with Polulo red stepper drivers and",
"I have connected two motors on the X and Y outputs of the",
"using RAMPS 1.4 with Polulo red stepper drivers and Arduino Mega R3. I",
"board or not? My only trouble is that when the board is on",
"the computer at the same time? ### Additional info from comments I am",
"the two stepper motors for the x and y axes. I am feeding",
"supply is on, then can I connect my Arduino to my PC using",
"run two stepper motors using Arduino Mega 2560 and RAMPS 1.4. But, somehow",
"I want to run two stepper motors using Arduino Mega 2560 and RAMPS",
"to run two stepper motors using Arduino Mega 2560 and RAMPS 1.4. But,",
"feeding 11.9 V supply to the RAMPS board. When powered on, can I",
"RAMPS board. When powered on, can I plug the USB to my computer?",
"the RAMPS, and the external power supply is on, then can I connect",
"than the two stepper motors for the x and y axes. I am",
"somehow I burned the Arduino while I was connecting the motor and plugging",
"Arduino while I was connecting the motor and plugging the board to the",
"the x and y axes. I am feeding 11.9 V supply to the",
"time? ### Additional info from comments I am using RAMPS 1.4 with Polulo",
"that when the board is on load, connecting the USB to computer motors",
"motors and not using any hotbed or anything else other than the two",
"and plugging the board to the computer. Can I plug external power supply",
"computer motors would take power by Arduino pins instead of the RAMPS external",
"plug the USB to my computer? Suppose I have connected two motors on",
"USB to computer motors would take power by Arduino pins instead of the",
"am only using two Nema 17 stepper motors and not using any hotbed",
"on, then can I connect my Arduino to my PC using USB? Will",
"Arduino Mega 2560 and RAMPS 1.4. But, somehow I burned the Arduino while",
"connect my Arduino to my PC using USB? Will it burn my board",
"at the same time? ### Additional info from comments I am using RAMPS",
"My only trouble is that when the board is on load, connecting the",
"drivers and Arduino Mega R3. I am only using two Nema 17 stepper",
"y axes. I am feeding 11.9 V supply to the RAMPS board. When",
"supply to the RAMPS board. When powered on, can I plug the USB",
"can I plug the USB to my computer? Suppose I have connected two",
"two Nema 17 stepper motors and not using any hotbed or anything else",
"plug external power supply and USB connection to the computer at the same",
"2560 and RAMPS 1.4. But, somehow I burned the Arduino while I was",
"and USB connection to the computer at the same time? ### Additional info",
"burn my board or not? My only trouble is that when the board",
"1.4 with Polulo red stepper drivers and Arduino Mega R3. I am only",
"power supply is on, then can I connect my Arduino to my PC",
"I am only using two Nema 17 stepper motors and not using any",
"Arduino Mega R3. I am only using two Nema 17 stepper motors and",
"using Arduino Mega 2560 and RAMPS 1.4. But, somehow I burned the Arduino",
"my board or not? My only trouble is that when the board is",
"Can I plug external power supply and USB connection to the computer at",
"X and Y outputs of the RAMPS, and the external power supply is",
"on the X and Y outputs of the RAMPS, and the external power",
"stepper motors using Arduino Mega 2560 and RAMPS 1.4. But, somehow I burned",
"the X and Y outputs of the RAMPS, and the external power supply",
"two stepper motors using Arduino Mega 2560 and RAMPS 1.4. But, somehow I",
"motors for the x and y axes. I am feeding 11.9 V supply",
"17 stepper motors and not using any hotbed or anything else other than",
"computer at the same time? ### Additional info from comments I am using",
"But, somehow I burned the Arduino while I was connecting the motor and",
"Y outputs of the RAMPS, and the external power supply is on, then",
"computer. Can I plug external power supply and USB connection to the computer",
"USB connection to the computer at the same time? ### Additional info from",
"stepper motors and not using any hotbed or anything else other than the",
"Suppose I have connected two motors on the X and Y outputs of",
"power supply and USB connection to the computer at the same time? ###",
"Mega R3. I am only using two Nema 17 stepper motors and not",
"V supply to the RAMPS board. When powered on, can I plug the",
"anything else other than the two stepper motors for the x and y",
"only trouble is that when the board is on load, connecting the USB",
"then can I connect my Arduino to my PC using USB? Will it",
"on load, connecting the USB to computer motors would take power by Arduino",
"the motor and plugging the board to the computer. Can I plug external",
"on, can I plug the USB to my computer? Suppose I have connected",
"hotbed or anything else other than the two stepper motors for the x",
"comments I am using RAMPS 1.4 with Polulo red stepper drivers and Arduino",
"and Arduino Mega R3. I am only using two Nema 17 stepper motors",
"powered on, can I plug the USB to my computer? Suppose I have",
"is on load, connecting the USB to computer motors would take power by",
"I connect my Arduino to my PC using USB? Will it burn my",
"plugging the board to the computer. Can I plug external power supply and",
"of the RAMPS, and the external power supply is on, then can I",
"Will it burn my board or not? My only trouble is that when",
"axes. I am feeding 11.9 V supply to the RAMPS board. When powered",
"and the external power supply is on, then can I connect my Arduino",
"I am feeding 11.9 V supply to the RAMPS board. When powered on,",
"RAMPS 1.4. But, somehow I burned the Arduino while I was connecting the",
"not? My only trouble is that when the board is on load, connecting",
"and y axes. I am feeding 11.9 V supply to the RAMPS board.",
"to the computer. Can I plug external power supply and USB connection to",
"motors using Arduino Mega 2560 and RAMPS 1.4. But, somehow I burned the",
"motors would take power by Arduino pins instead of the RAMPS external supply.",
"external power supply and USB connection to the computer at the same time?",
"I burned the Arduino while I was connecting the motor and plugging the",
"motor and plugging the board to the computer. Can I plug external power",
"computer? Suppose I have connected two motors on the X and Y outputs",
"### Additional info from comments I am using RAMPS 1.4 with Polulo red",
"Mega 2560 and RAMPS 1.4. But, somehow I burned the Arduino while I",
"using any hotbed or anything else other than the two stepper motors for",
"USB to my computer? Suppose I have connected two motors on the X",
"while I was connecting the motor and plugging the board to the computer.",
"using two Nema 17 stepper motors and not using any hotbed or anything",
"RAMPS, and the external power supply is on, then can I connect my",
"was connecting the motor and plugging the board to the computer. Can I",
"connecting the USB to computer motors would take power by Arduino pins instead",
"connected two motors on the X and Y outputs of the RAMPS, and",
"using USB? Will it burn my board or not? My only trouble is",
"only using two Nema 17 stepper motors and not using any hotbed or"
] |
[
"the heated to reach the target temperature as fast as possible, so I",
"Do I need to put a fuse or some other kind of safety?",
"1200Watt bed, so I really want to make sure that it is safe",
"want the heated to reach the target temperature as fast as possible, so",
"I'm building a 40x40x40cm corexy and I am quite impatient so I want",
"bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the wiring in",
"corexy and I am quite impatient so I want the heated to reach",
"the target temperature as fast as possible, so I ordered a [Keenovo silicone",
"so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed,",
"heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so I really want to make",
"bed, so I really want to make sure that it is safe to",
"make sure that it is safe to use. I also bought a [Crydom",
"that it is safe to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR.",
"a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so I really",
"I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the",
"a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the wiring in the",
"target temperature as fast as possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV)",
"D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the wiring in the diagram I",
"so I want the heated to reach the target temperature as fast as",
"ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so I",
"safe to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell",
"I really want to make sure that it is safe to use. I",
"is safe to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone",
"I want the heated to reach the target temperature as fast as possible,",
"It is a 220VAC 1200Watt bed, so I really want to make sure",
"[Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the wiring in the diagram",
"safe? Do I need to put a fuse or some other kind of",
"if the wiring in the diagram I made below is safe? Do I",
"to make sure that it is safe to use. I also bought a",
"am quite impatient so I want the heated to reach the target temperature",
"to reach the target temperature as fast as possible, so I ordered a",
"it is safe to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could",
"the wiring in the diagram I made below is safe? Do I need",
"building a 40x40x40cm corexy and I am quite impatient so I want the",
"below is safe? Do I need to put a fuse or some other",
"temperature as fast as possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It",
"use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if",
"in the diagram I made below is safe? Do I need to put",
"I am quite impatient so I want the heated to reach the target",
"as possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC",
"[Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so I really want",
"fast as possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a",
"really want to make sure that it is safe to use. I also",
"sure that it is safe to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf)",
"possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt",
"silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so I really want to",
"to use. I also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me",
"40x40x40cm corexy and I am quite impatient so I want the heated to",
"as fast as possible, so I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is",
"quite impatient so I want the heated to reach the target temperature as",
"so I really want to make sure that it is safe to use.",
"wiring in the diagram I made below is safe? Do I need to",
"Could someone tell me if the wiring in the diagram I made below",
"220VAC 1200Watt bed, so I really want to make sure that it is",
"SSR. Could someone tell me if the wiring in the diagram I made",
"also bought a [Crydom D2450](http://www.crydom.com/en/products/catalog/series-1-240-ac-panel-mount.pdf) SSR. Could someone tell me if the wiring",
"the diagram I made below is safe? Do I need to put a",
"I made below is safe? Do I need to put a fuse or",
"is safe? Do I need to put a fuse or some other kind",
"I need to put a fuse or some other kind of safety? [](https://i.stack.imgur.com/dd7TA.jpg)",
"heated to reach the target temperature as fast as possible, so I ordered",
"tell me if the wiring in the diagram I made below is safe?",
"diagram I made below is safe? Do I need to put a fuse",
"and I am quite impatient so I want the heated to reach the",
"is a 220VAC 1200Watt bed, so I really want to make sure that",
"a 220VAC 1200Watt bed, so I really want to make sure that it",
"I ordered a [Keenovo silicone heater](https://www.aliexpress.com/item/400X400mm-1200W-220V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-Pad-for-Huge-Mega-Cube-3D/32550597606.html?spm=a2g0s.9042311.0.0.Io1mMV) It is a 220VAC 1200Watt bed, so",
"made below is safe? Do I need to put a fuse or some",
"reach the target temperature as fast as possible, so I ordered a [Keenovo",
"impatient so I want the heated to reach the target temperature as fast",
"a 40x40x40cm corexy and I am quite impatient so I want the heated",
"want to make sure that it is safe to use. I also bought",
"someone tell me if the wiring in the diagram I made below is",
"me if the wiring in the diagram I made below is safe? Do"
] |
[
"With hot plastic being laid down layer after layer, I am worried about",
"only print in a well ventilated work space? Should I add additional ventilation?",
"layer, I am worried about fumes. Should I only print in a well",
"am worried about fumes. Should I only print in a well ventilated work",
"fumes. Should I only print in a well ventilated work space? Should I",
"I only print in a well ventilated work space? Should I add additional",
"layer after layer, I am worried about fumes. Should I only print in",
"laid down layer after layer, I am worried about fumes. Should I only",
"down layer after layer, I am worried about fumes. Should I only print",
"hot plastic being laid down layer after layer, I am worried about fumes.",
"I am worried about fumes. Should I only print in a well ventilated",
"plastic being laid down layer after layer, I am worried about fumes. Should",
"Should I only print in a well ventilated work space? Should I add",
"about fumes. Should I only print in a well ventilated work space? Should",
"being laid down layer after layer, I am worried about fumes. Should I",
"worried about fumes. Should I only print in a well ventilated work space?",
"after layer, I am worried about fumes. Should I only print in a"
] |
[
"print itself takes on my TEVO Tarantula with Marlin firmware. The time difference",
"with Marlin firmware. The time difference is about 15 %, at requested 50",
"Marlin firmware. The time difference is about 15 %, at requested 50 mm/s",
"always is giving me less printing time than the print itself takes on",
"printing time than the print itself takes on my TEVO Tarantula with Marlin",
"less printing time than the print itself takes on my TEVO Tarantula with",
"noticed that Cura always is giving me less printing time than the print",
"TEVO Tarantula with Marlin firmware. The time difference is about 15 %, at",
"difference is about 15 %, at requested 50 mm/s printing speed. **How could",
"15 %, at requested 50 mm/s printing speed. **How could I verify real",
"than the print itself takes on my TEVO Tarantula with Marlin firmware. The",
"I noticed that Cura always is giving me less printing time than the",
"that Cura always is giving me less printing time than the print itself",
"my TEVO Tarantula with Marlin firmware. The time difference is about 15 %,",
"itself takes on my TEVO Tarantula with Marlin firmware. The time difference is",
"time difference is about 15 %, at requested 50 mm/s printing speed. **How",
"Cura always is giving me less printing time than the print itself takes",
"is giving me less printing time than the print itself takes on my",
"takes on my TEVO Tarantula with Marlin firmware. The time difference is about",
"firmware. The time difference is about 15 %, at requested 50 mm/s printing",
"me less printing time than the print itself takes on my TEVO Tarantula",
"is about 15 %, at requested 50 mm/s printing speed. **How could I",
"%, at requested 50 mm/s printing speed. **How could I verify real printing",
"The time difference is about 15 %, at requested 50 mm/s printing speed.",
"Recently I noticed that Cura always is giving me less printing time than",
"giving me less printing time than the print itself takes on my TEVO",
"the print itself takes on my TEVO Tarantula with Marlin firmware. The time",
"on my TEVO Tarantula with Marlin firmware. The time difference is about 15",
"about 15 %, at requested 50 mm/s printing speed. **How could I verify",
"at requested 50 mm/s printing speed. **How could I verify real printing speed?**",
"time than the print itself takes on my TEVO Tarantula with Marlin firmware.",
"Tarantula with Marlin firmware. The time difference is about 15 %, at requested"
] |
[
"X1 power brick with a standard RAMPS 1.4 board - rather than the",
"brick with commercial printers lacking heatbeds. Is this possible with a RepRap printer",
"brick. I was wondering if it we're possible to use the same TronXY",
"this possible with a RepRap printer using a RAMPS board? I'm referring specifically",
"a standard RAMPS 1.4 board - rather than the special board the TronXY",
"Is this possible with a RepRap printer using a RAMPS board? I'm referring",
"possible with a RepRap printer using a RAMPS board? I'm referring specifically to",
"with a RepRap printer using a RAMPS board? I'm referring specifically to the",
"have a heated bed. I have heard that it is possible to use",
"a RAMPS board? I'm referring specifically to the TronXY X1 power brick. I",
"RAMPS 1.4 board - rather than the special board the TronXY X1 uses.",
"brick with a standard RAMPS 1.4 board - rather than the special board",
"printers lacking heatbeds. Is this possible with a RepRap printer using a RAMPS",
"not have a heated bed. I have heard that it is possible to",
"the same TronXY X1 power brick with a standard RAMPS 1.4 board -",
"use the same TronXY X1 power brick with a standard RAMPS 1.4 board",
"standard RAMPS 1.4 board - rather than the special board the TronXY X1",
"will not have a heated bed. I have heard that it is possible",
"heard that it is possible to use a power brick with commercial printers",
"if it we're possible to use the same TronXY X1 power brick with",
"same TronXY X1 power brick with a standard RAMPS 1.4 board - rather",
"board? I'm referring specifically to the TronXY X1 power brick. I was wondering",
"wondering if it we're possible to use the same TronXY X1 power brick",
"printer that will not have a heated bed. I have heard that it",
"power brick. I was wondering if it we're possible to use the same",
"I was wondering if it we're possible to use the same TronXY X1",
"designing a RepRap 3D printer that will not have a heated bed. I",
"is possible to use a power brick with commercial printers lacking heatbeds. Is",
"it is possible to use a power brick with commercial printers lacking heatbeds.",
"that will not have a heated bed. I have heard that it is",
"with a standard RAMPS 1.4 board - rather than the special board the",
"to use the same TronXY X1 power brick with a standard RAMPS 1.4",
"the TronXY X1 power brick. I was wondering if it we're possible to",
"3D printer that will not have a heated bed. I have heard that",
"RepRap printer using a RAMPS board? I'm referring specifically to the TronXY X1",
"a RepRap 3D printer that will not have a heated bed. I have",
"heatbeds. Is this possible with a RepRap printer using a RAMPS board? I'm",
"X1 power brick. I was wondering if it we're possible to use the",
"referring specifically to the TronXY X1 power brick. I was wondering if it",
"it we're possible to use the same TronXY X1 power brick with a",
"use a power brick with commercial printers lacking heatbeds. Is this possible with",
"we're possible to use the same TronXY X1 power brick with a standard",
"a power brick with commercial printers lacking heatbeds. Is this possible with a",
"TronXY X1 power brick with a standard RAMPS 1.4 board - rather than",
"specifically to the TronXY X1 power brick. I was wondering if it we're",
"that it is possible to use a power brick with commercial printers lacking",
"power brick with commercial printers lacking heatbeds. Is this possible with a RepRap",
"I have heard that it is possible to use a power brick with",
"TronXY X1 power brick. I was wondering if it we're possible to use",
"power brick with a standard RAMPS 1.4 board - rather than the special",
"have heard that it is possible to use a power brick with commercial",
"using a RAMPS board? I'm referring specifically to the TronXY X1 power brick.",
"bed. I have heard that it is possible to use a power brick",
"possible to use the same TronXY X1 power brick with a standard RAMPS",
"to use a power brick with commercial printers lacking heatbeds. Is this possible",
"currently designing a RepRap 3D printer that will not have a heated bed.",
"to the TronXY X1 power brick. I was wondering if it we're possible",
"RAMPS board? I'm referring specifically to the TronXY X1 power brick. I was",
"commercial printers lacking heatbeds. Is this possible with a RepRap printer using a",
"RepRap 3D printer that will not have a heated bed. I have heard",
"lacking heatbeds. Is this possible with a RepRap printer using a RAMPS board?",
"a RepRap printer using a RAMPS board? I'm referring specifically to the TronXY",
"I'm currently designing a RepRap 3D printer that will not have a heated",
"a heated bed. I have heard that it is possible to use a",
"I'm referring specifically to the TronXY X1 power brick. I was wondering if",
"possible to use a power brick with commercial printers lacking heatbeds. Is this",
"was wondering if it we're possible to use the same TronXY X1 power",
"with commercial printers lacking heatbeds. Is this possible with a RepRap printer using",
"heated bed. I have heard that it is possible to use a power",
"printer using a RAMPS board? I'm referring specifically to the TronXY X1 power"
] |
[
"how (h/w connections and firmware modification) can I do it for the extruder?",
"is in home position before it starts to drive for the very first",
"question as some of you mentioned that the question is not clear. I",
"X, Y, and Z axes. I was wondering how (h/w connections and firmware",
"mentioned that the question is not clear. I am using a RAMPS 1.4",
"board with an Arduino mega 2560. I need to drive a stepper motor",
"an extruder using either E0 or E1. I am using Repetier-Firmware and can",
"was wondering how (h/w connections and firmware modification) can I do it for",
"need to make sure that the extruder is in home position before it",
"using either E0 or E1. I am using Repetier-Firmware and can drive the",
"connect to the end stop and perform this homing operation. I can do",
"trying to use a switch to connect to the end stop and perform",
"using Repetier-Firmware and can drive the extruder (stepper motor) using the E0 (RAMPS",
"with an Arduino mega 2560. I need to drive a stepper motor as",
"(stepper motor) using the E0 (RAMPS 1.4). Now for my application, I need",
"I am trying to use a switch to connect to the end stop",
"using a RAMPS 1.4 board with an Arduino mega 2560. I need to",
"extruder is in home position before it starts to drive for the very",
"drive the extruder (stepper motor) using the E0 (RAMPS 1.4). Now for my",
"home position before it starts to drive for the very first time. I",
"is not clear. I am using a RAMPS 1.4 board with an Arduino",
"2560. I need to drive a stepper motor as an extruder using either",
"starts to drive for the very first time. I am trying to use",
"or E1. I am using Repetier-Firmware and can drive the extruder (stepper motor)",
"to drive a stepper motor as an extruder using either E0 or E1.",
"Now for my application, I need to make sure that the extruder is",
"can do this for X, Y, and Z axes. I was wondering how",
"you mentioned that the question is not clear. I am using a RAMPS",
"extruder using either E0 or E1. I am using Repetier-Firmware and can drive",
"drive for the very first time. I am trying to use a switch",
"mega 2560. I need to drive a stepper motor as an extruder using",
"I am using a RAMPS 1.4 board with an Arduino mega 2560. I",
"to use a switch to connect to the end stop and perform this",
"the end stop and perform this homing operation. I can do this for",
"switch to connect to the end stop and perform this homing operation. I",
"Z axes. I was wondering how (h/w connections and firmware modification) can I",
"not clear. I am using a RAMPS 1.4 board with an Arduino mega",
"am using Repetier-Firmware and can drive the extruder (stepper motor) using the E0",
"time. I am trying to use a switch to connect to the end",
"sure that the extruder is in home position before it starts to drive",
"can drive the extruder (stepper motor) using the E0 (RAMPS 1.4). Now for",
"need to drive a stepper motor as an extruder using either E0 or",
"axes. I was wondering how (h/w connections and firmware modification) can I do",
"either E0 or E1. I am using Repetier-Firmware and can drive the extruder",
"end stop and perform this homing operation. I can do this for X,",
"and perform this homing operation. I can do this for X, Y, and",
"to drive for the very first time. I am trying to use a",
"homing operation. I can do this for X, Y, and Z axes. I",
"am using a RAMPS 1.4 board with an Arduino mega 2560. I need",
"question is not clear. I am using a RAMPS 1.4 board with an",
"before it starts to drive for the very first time. I am trying",
"my application, I need to make sure that the extruder is in home",
"some of you mentioned that the question is not clear. I am using",
"E0 or E1. I am using Repetier-Firmware and can drive the extruder (stepper",
"to the end stop and perform this homing operation. I can do this",
"a RAMPS 1.4 board with an Arduino mega 2560. I need to drive",
"using the E0 (RAMPS 1.4). Now for my application, I need to make",
"application, I need to make sure that the extruder is in home position",
"position before it starts to drive for the very first time. I am",
"extruder (stepper motor) using the E0 (RAMPS 1.4). Now for my application, I",
"this homing operation. I can do this for X, Y, and Z axes.",
"the question is not clear. I am using a RAMPS 1.4 board with",
"RAMPS 1.4 board with an Arduino mega 2560. I need to drive a",
"the extruder is in home position before it starts to drive for the",
"E0 (RAMPS 1.4). Now for my application, I need to make sure that",
"to connect to the end stop and perform this homing operation. I can",
"it starts to drive for the very first time. I am trying to",
"a stepper motor as an extruder using either E0 or E1. I am",
"for my application, I need to make sure that the extruder is in",
"and can drive the extruder (stepper motor) using the E0 (RAMPS 1.4). Now",
"in home position before it starts to drive for the very first time.",
"use a switch to connect to the end stop and perform this homing",
"first time. I am trying to use a switch to connect to the",
"do this for X, Y, and Z axes. I was wondering how (h/w",
"1.4). Now for my application, I need to make sure that the extruder",
"the very first time. I am trying to use a switch to connect",
"(RAMPS 1.4). Now for my application, I need to make sure that the",
"I can do this for X, Y, and Z axes. I was wondering",
"as an extruder using either E0 or E1. I am using Repetier-Firmware and",
"the E0 (RAMPS 1.4). Now for my application, I need to make sure",
"E1. I am using Repetier-Firmware and can drive the extruder (stepper motor) using",
"have extended my question as some of you mentioned that the question is",
"Repetier-Firmware and can drive the extruder (stepper motor) using the E0 (RAMPS 1.4).",
"stepper motor as an extruder using either E0 or E1. I am using",
"stop and perform this homing operation. I can do this for X, Y,",
"of you mentioned that the question is not clear. I am using a",
"I have extended my question as some of you mentioned that the question",
"Y, and Z axes. I was wondering how (h/w connections and firmware modification)",
"for X, Y, and Z axes. I was wondering how (h/w connections and",
"I was wondering how (h/w connections and firmware modification) can I do it",
"motor) using the E0 (RAMPS 1.4). Now for my application, I need to",
"wondering how (h/w connections and firmware modification) can I do it for the",
"I am using Repetier-Firmware and can drive the extruder (stepper motor) using the",
"an Arduino mega 2560. I need to drive a stepper motor as an",
"that the question is not clear. I am using a RAMPS 1.4 board",
"for the very first time. I am trying to use a switch to",
"Note: I have extended my question as some of you mentioned that the",
"am trying to use a switch to connect to the end stop and",
"to make sure that the extruder is in home position before it starts",
"my question as some of you mentioned that the question is not clear.",
"drive a stepper motor as an extruder using either E0 or E1. I",
"motor as an extruder using either E0 or E1. I am using Repetier-Firmware",
"I need to make sure that the extruder is in home position before",
"very first time. I am trying to use a switch to connect to",
"perform this homing operation. I can do this for X, Y, and Z",
"clear. I am using a RAMPS 1.4 board with an Arduino mega 2560.",
"1.4 board with an Arduino mega 2560. I need to drive a stepper",
"make sure that the extruder is in home position before it starts to",
"that the extruder is in home position before it starts to drive for",
"the extruder (stepper motor) using the E0 (RAMPS 1.4). Now for my application,",
"this for X, Y, and Z axes. I was wondering how (h/w connections",
"and Z axes. I was wondering how (h/w connections and firmware modification) can",
"a switch to connect to the end stop and perform this homing operation.",
"as some of you mentioned that the question is not clear. I am",
"I need to drive a stepper motor as an extruder using either E0",
"Arduino mega 2560. I need to drive a stepper motor as an extruder",
"extended my question as some of you mentioned that the question is not",
"operation. I can do this for X, Y, and Z axes. I was"
] |
[
"a new printer if anyone knows a control board that has this sort",
"to write some software to take a picture check the print hasn't moved",
"back to the computer before continuing printing? I am happy to build/buy a",
"know if any of the available software/firmware allows custom scripts or calling back",
"like to be able to add custom commands/script to be executed during a",
"custom commands/script to be executed during a print. For example I would like",
"software to take a picture check the print hasn't moved off the bead",
"or calling back to the computer before continuing printing? I am happy to",
"continuing printing? I am happy to build/buy a new printer if anyone knows",
"would like to write some software to take a picture check the print",
"like to write some software to take a picture check the print hasn't",
"some software to take a picture check the print hasn't moved off the",
"example I would like to write some software to take a picture check",
"I would like to write some software to take a picture check the",
"build/buy a new printer if anyone knows a control board that has this",
"off the bead between layers. Does anyone know if any of the available",
"able to add custom commands/script to be executed during a print. For example",
"allows custom scripts or calling back to the computer before continuing printing? I",
"write some software to take a picture check the print hasn't moved off",
"picture check the print hasn't moved off the bead between layers. Does anyone",
"would like to be able to add custom commands/script to be executed during",
"to build/buy a new printer if anyone knows a control board that has",
"new printer if anyone knows a control board that has this sort of",
"to be able to add custom commands/script to be executed during a print.",
"print. For example I would like to write some software to take a",
"I am happy to build/buy a new printer if anyone knows a control",
"moved off the bead between layers. Does anyone know if any of the",
"if any of the available software/firmware allows custom scripts or calling back to",
"to add custom commands/script to be executed during a print. For example I",
"to take a picture check the print hasn't moved off the bead between",
"any of the available software/firmware allows custom scripts or calling back to the",
"commands/script to be executed during a print. For example I would like to",
"the available software/firmware allows custom scripts or calling back to the computer before",
"happy to build/buy a new printer if anyone knows a control board that",
"printing? I am happy to build/buy a new printer if anyone knows a",
"scripts or calling back to the computer before continuing printing? I am happy",
"computer before continuing printing? I am happy to build/buy a new printer if",
"bead between layers. Does anyone know if any of the available software/firmware allows",
"software/firmware allows custom scripts or calling back to the computer before continuing printing?",
"calling back to the computer before continuing printing? I am happy to build/buy",
"a print. For example I would like to write some software to take",
"For example I would like to write some software to take a picture",
"the bead between layers. Does anyone know if any of the available software/firmware",
"executed during a print. For example I would like to write some software",
"I would like to be able to add custom commands/script to be executed",
"Does anyone know if any of the available software/firmware allows custom scripts or",
"before continuing printing? I am happy to build/buy a new printer if anyone",
"to be executed during a print. For example I would like to write",
"the print hasn't moved off the bead between layers. Does anyone know if",
"add custom commands/script to be executed during a print. For example I would",
"print hasn't moved off the bead between layers. Does anyone know if any",
"check the print hasn't moved off the bead between layers. Does anyone know",
"be executed during a print. For example I would like to write some",
"custom scripts or calling back to the computer before continuing printing? I am",
"printer if anyone knows a control board that has this sort of feature.",
"layers. Does anyone know if any of the available software/firmware allows custom scripts",
"take a picture check the print hasn't moved off the bead between layers.",
"hasn't moved off the bead between layers. Does anyone know if any of",
"during a print. For example I would like to write some software to",
"to the computer before continuing printing? I am happy to build/buy a new",
"am happy to build/buy a new printer if anyone knows a control board",
"the computer before continuing printing? I am happy to build/buy a new printer",
"be able to add custom commands/script to be executed during a print. For",
"available software/firmware allows custom scripts or calling back to the computer before continuing",
"anyone know if any of the available software/firmware allows custom scripts or calling",
"a picture check the print hasn't moved off the bead between layers. Does",
"of the available software/firmware allows custom scripts or calling back to the computer",
"between layers. Does anyone know if any of the available software/firmware allows custom"
] |
[
"vertical lines described as \"banding\"? Would the most likely culprit be the extruder?",
"the most likely culprit be the extruder? FWIW, this was printed in \"vase",
"Are these vertical lines described as \"banding\"? Would the most likely culprit be",
"\"banding\"? Would the most likely culprit be the extruder? FWIW, this was printed",
"lines described as \"banding\"? Would the most likely culprit be the extruder? FWIW,",
"culprit be the extruder? FWIW, this was printed in \"vase mode\". [](https://i.stack.imgur.com/0ZCPF.jpg)",
"described as \"banding\"? Would the most likely culprit be the extruder? FWIW, this",
"most likely culprit be the extruder? FWIW, this was printed in \"vase mode\".",
"Would the most likely culprit be the extruder? FWIW, this was printed in",
"as \"banding\"? Would the most likely culprit be the extruder? FWIW, this was",
"likely culprit be the extruder? FWIW, this was printed in \"vase mode\". [![Vase",
"these vertical lines described as \"banding\"? Would the most likely culprit be the"
] |
[
"again can't extrude after it's created. How can I connect the pieces after",
"Printer. I am very new to Autodesk Fusion360 so I am running into",
"am having trouble sketching a rectangle and then a text character and extruding",
"characters with my 3D Printer. I am very new to Autodesk Fusion360 so",
"next sketch object. How can I create both sketches and select different ones",
"connect them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example Kanji Stencil\")](https://i.stack.imgur.com/hLaBH.png \"Example",
"character and extruding them separately. If I extrude one they both disappear. Therefore",
"I extrude one they both disappear. Therefore I have to sketch one, then",
"to sketch one, then extrude, then create the next sketch object. How can",
"How can I create both sketches and select different ones to extrude? 2.",
"work. I once again can't extrude after it's created. How can I connect",
"having trouble sketching a rectangle and then a text character and extruding them",
"to Autodesk Fusion360 so I am running into some barriers: 1. I am",
"make stencils of Japanese Kanji characters with my 3D Printer. I am very",
"am trying to make stencils of Japanese Kanji characters with my 3D Printer.",
"so I am running into some barriers: 1. I am having trouble sketching",
"barriers: 1. I am having trouble sketching a rectangle and then a text",
"didn't work. I once again can't extrude after it's created. How can I",
"once again can't extrude after it's created. How can I connect the pieces",
"where my stencil has parts that are disconnected (see example below). I've tried",
"stencil has parts that are disconnected (see example below). I've tried sketching lines",
"2. I am having this basic problem where my stencil has parts that",
"am having this basic problem where my stencil has parts that are disconnected",
"both disappear. Therefore I have to sketch one, then extrude, then create the",
"a rectangle and then a text character and extruding them separately. If I",
"both sketches and select different ones to extrude? 2. I am having this",
"having this basic problem where my stencil has parts that are disconnected (see",
"very new to Autodesk Fusion360 so I am running into some barriers: 1.",
"this basic problem where my stencil has parts that are disconnected (see example",
"my stencil has parts that are disconnected (see example below). I've tried sketching",
"them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example Kanji Stencil\")](https://i.stack.imgur.com/hLaBH.png \"Example Kanji",
"to make stencils of Japanese Kanji characters with my 3D Printer. I am",
"I am running into some barriers: 1. I am having trouble sketching a",
"below). I've tried sketching lines and thin rectangles to connect the pieces but",
"to extrude? 2. I am having this basic problem where my stencil has",
"stencils of Japanese Kanji characters with my 3D Printer. I am very new",
"rectangles to connect the pieces but they both didn't work. I once again",
"sketch one, then extrude, then create the next sketch object. How can I",
"and then a text character and extruding them separately. If I extrude one",
"am very new to Autodesk Fusion360 so I am running into some barriers:",
"pieces but they both didn't work. I once again can't extrude after it's",
"after it's created. How can I connect the pieces after extruding? How can",
"one, then extrude, then create the next sketch object. How can I create",
"trying to make stencils of Japanese Kanji characters with my 3D Printer. I",
"Fusion360 so I am running into some barriers: 1. I am having trouble",
"text character and extruding them separately. If I extrude one they both disappear.",
"to connect the pieces but they both didn't work. I once again can't",
"can't extrude after it's created. How can I connect the pieces after extruding?",
"inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example Kanji Stencil\")](https://i.stack.imgur.com/hLaBH.png \"Example Kanji Stencil\")",
"some barriers: 1. I am having trouble sketching a rectangle and then a",
"I am trying to make stencils of Japanese Kanji characters with my 3D",
"I have to sketch one, then extrude, then create the next sketch object.",
"can I connect the pieces after extruding? How can I connect them inside",
"the next sketch object. How can I create both sketches and select different",
"thin rectangles to connect the pieces but they both didn't work. I once",
"extrude one they both disappear. Therefore I have to sketch one, then extrude,",
"can I create both sketches and select different ones to extrude? 2. I",
"am running into some barriers: 1. I am having trouble sketching a rectangle",
"extrude? 2. I am having this basic problem where my stencil has parts",
"and select different ones to extrude? 2. I am having this basic problem",
"trouble sketching a rectangle and then a text character and extruding them separately.",
"my 3D Printer. I am very new to Autodesk Fusion360 so I am",
"then extrude, then create the next sketch object. How can I create both",
"connect the pieces after extruding? How can I connect them inside a text",
"sketching lines and thin rectangles to connect the pieces but they both didn't",
"and extruding them separately. If I extrude one they both disappear. Therefore I",
"extrude after it's created. How can I connect the pieces after extruding? How",
"the pieces after extruding? How can I connect them inside a text object?",
"pieces after extruding? How can I connect them inside a text object? [![Example",
"one they both disappear. Therefore I have to sketch one, then extrude, then",
"that are disconnected (see example below). I've tried sketching lines and thin rectangles",
"it's created. How can I connect the pieces after extruding? How can I",
"separately. If I extrude one they both disappear. Therefore I have to sketch",
"sketches and select different ones to extrude? 2. I am having this basic",
"I've tried sketching lines and thin rectangles to connect the pieces but they",
"parts that are disconnected (see example below). I've tried sketching lines and thin",
"example below). I've tried sketching lines and thin rectangles to connect the pieces",
"both didn't work. I once again can't extrude after it's created. How can",
"after extruding? How can I connect them inside a text object? [![Example Kanji",
"a text character and extruding them separately. If I extrude one they both",
"Autodesk Fusion360 so I am running into some barriers: 1. I am having",
"How can I connect them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example",
"3D Printer. I am very new to Autodesk Fusion360 so I am running",
"Japanese Kanji characters with my 3D Printer. I am very new to Autodesk",
"I create both sketches and select different ones to extrude? 2. I am",
"create the next sketch object. How can I create both sketches and select",
"object. How can I create both sketches and select different ones to extrude?",
"select different ones to extrude? 2. I am having this basic problem where",
"1. I am having trouble sketching a rectangle and then a text character",
"Kanji characters with my 3D Printer. I am very new to Autodesk Fusion360",
"If I extrude one they both disappear. Therefore I have to sketch one,",
"Therefore I have to sketch one, then extrude, then create the next sketch",
"problem where my stencil has parts that are disconnected (see example below). I've",
"tried sketching lines and thin rectangles to connect the pieces but they both",
"running into some barriers: 1. I am having trouble sketching a rectangle and",
"into some barriers: 1. I am having trouble sketching a rectangle and then",
"extrude, then create the next sketch object. How can I create both sketches",
"I am having this basic problem where my stencil has parts that are",
"has parts that are disconnected (see example below). I've tried sketching lines and",
"have to sketch one, then extrude, then create the next sketch object. How",
"they both didn't work. I once again can't extrude after it's created. How",
"I am very new to Autodesk Fusion360 so I am running into some",
"extruding them separately. If I extrude one they both disappear. Therefore I have",
"the pieces but they both didn't work. I once again can't extrude after",
"sketch object. How can I create both sketches and select different ones to",
"basic problem where my stencil has parts that are disconnected (see example below).",
"lines and thin rectangles to connect the pieces but they both didn't work.",
"then create the next sketch object. How can I create both sketches and",
"of Japanese Kanji characters with my 3D Printer. I am very new to",
"connect the pieces but they both didn't work. I once again can't extrude",
"create both sketches and select different ones to extrude? 2. I am having",
"they both disappear. Therefore I have to sketch one, then extrude, then create",
"ones to extrude? 2. I am having this basic problem where my stencil",
"I am having trouble sketching a rectangle and then a text character and",
"them separately. If I extrude one they both disappear. Therefore I have to",
"with my 3D Printer. I am very new to Autodesk Fusion360 so I",
"I connect them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example Kanji Stencil\")](https://i.stack.imgur.com/hLaBH.png",
"disconnected (see example below). I've tried sketching lines and thin rectangles to connect",
"How can I connect the pieces after extruding? How can I connect them",
"then a text character and extruding them separately. If I extrude one they",
"disappear. Therefore I have to sketch one, then extrude, then create the next",
"created. How can I connect the pieces after extruding? How can I connect",
"(see example below). I've tried sketching lines and thin rectangles to connect the",
"new to Autodesk Fusion360 so I am running into some barriers: 1. I",
"sketching a rectangle and then a text character and extruding them separately. If",
"and thin rectangles to connect the pieces but they both didn't work. I",
"I connect the pieces after extruding? How can I connect them inside a",
"but they both didn't work. I once again can't extrude after it's created.",
"rectangle and then a text character and extruding them separately. If I extrude",
"are disconnected (see example below). I've tried sketching lines and thin rectangles to",
"I once again can't extrude after it's created. How can I connect the",
"can I connect them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png \"Example Kanji",
"extruding? How can I connect them inside a text object? [![Example Kanji Stencil](https://i.stack.imgur.com/hLaBH.png",
"different ones to extrude? 2. I am having this basic problem where my"
] |
[
"it on E1 instead. If you have any better idea how to fix",
"potentiometer on E0 so the motor isn't working properly anymore. I want to",
"E1 instead. If you have any better idea how to fix this instead",
"problem as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in my `RAMPS.h`",
"instead. If you have any better idea how to fix this instead of",
"idea how to fix this instead of changing code in firmware, feel free",
"any better idea how to fix this instead of changing code in firmware,",
"If you have any better idea how to fix this instead of changing",
"those lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my",
"my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0",
"as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0 so the motor",
"I've recently burnt my potentiometer on E0 so the motor isn't working properly",
"have the same problem as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines",
"[this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in my `RAMPS.h` file as",
"my potentiometer on E0 so the motor isn't working properly anymore. I want",
"anymore. I want to use it on E1 instead. If you have any",
"motor isn't working properly anymore. I want to use it on E1 instead.",
"seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0 so the motor isn't",
"have any better idea how to fix this instead of changing code in",
"working properly anymore. I want to use it on E1 instead. If you",
"I have the same problem as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those",
"the motor isn't working properly anymore. I want to use it on E1",
"on E0 so the motor isn't working properly anymore. I want to use",
"better idea how to fix this instead of changing code in firmware, feel",
"`RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0 so",
"same problem as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in my",
"but I don't have those lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png).",
"person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in my `RAMPS.h` file as seen",
"to fix this instead of changing code in firmware, feel free to share.",
"burnt my potentiometer on E0 so the motor isn't working properly anymore. I",
"on E1 instead. If you have any better idea how to fix this",
"want to use it on E1 instead. If you have any better idea",
"you have any better idea how to fix this instead of changing code",
"to use it on E1 instead. If you have any better idea how",
"as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in my `RAMPS.h` file",
"recently burnt my potentiometer on E0 so the motor isn't working properly anymore.",
"I want to use it on E1 instead. If you have any better",
"don't have those lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently",
"[here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0 so the motor isn't working",
"isn't working properly anymore. I want to use it on E1 instead. If",
"lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer",
"use it on E1 instead. If you have any better idea how to",
"how to fix this instead of changing code in firmware, feel free to",
"have those lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt",
"properly anymore. I want to use it on E1 instead. If you have",
"the same problem as [this person](https://www.thingiverse.com/groups/tevo-tarantula-owners/forums/general/topic:29448) but I don't have those lines in",
"so the motor isn't working properly anymore. I want to use it on",
"file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on E0 so the",
"in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've recently burnt my potentiometer on",
"E0 so the motor isn't working properly anymore. I want to use it",
"I don't have those lines in my `RAMPS.h` file as seen [here](http://joxi.ru/DmBgR75UNe8k52.png). I've"
] |
[
"area: 12x12 cm). I would like to switch to a glass bed and",
"smaller heated bed for ABS and a bigger one for PLA. Would the",
"cm glass plate). Would it be possible to use the old heating resistor",
"a bigger one for PLA. Would the glass crack due to non uniform",
"rework my printer to increase the printing area to 20 cm (22x22 cm",
"have a smaller heated bed for ABS and a bigger one for PLA.",
"the printing area to 20 cm (22x22 cm glass plate). Would it be",
"hot area will stay hot and basically never really spread the heat to",
"(printing area: 12x12 cm). I would like to switch to a glass bed",
"would have a smaller heated bed for ABS and a bigger one for",
"bed and to rework my printer to increase the printing area to 20",
"switch to a glass bed and to rework my printer to increase the",
"ABS and a bigger one for PLA. Would the glass crack due to",
"increase the printing area to 20 cm (22x22 cm glass plate). Would it",
"(22x22 cm glass plate). Would it be possible to use the old heating",
"possible to use the old heating resistor placed only in the centre? this",
"glass crack due to non uniform heating? This is because glass has a",
"non uniform heating? This is because glass has a conductivity of less than",
"use the old heating resistor placed only in the centre? this way I",
"centre? this way I would have a smaller heated bed for ABS and",
"placed only in the centre? this way I would have a smaller heated",
"glass plate). Would it be possible to use the old heating resistor placed",
"cm). I would like to switch to a glass bed and to rework",
"Would the glass crack due to non uniform heating? This is because glass",
"bed for ABS and a bigger one for PLA. Would the glass crack",
"I have a 15x15 cm heating resistor from my current printer (printing area:",
"the hot area will stay hot and basically never really spread the heat",
"basically never really spread the heat to the surrounding area. So the frame",
"hot and basically never really spread the heat to the surrounding area. So",
"surrounding area. So the frame will be cold and the center hot, causing",
"than 5 W/mK, therefore the hot area will stay hot and basically never",
"never really spread the heat to the surrounding area. So the frame will",
"uniform heating? This is because glass has a conductivity of less than 5",
"of less than 5 W/mK, therefore the hot area will stay hot and",
"be possible to use the old heating resistor placed only in the centre?",
"because glass has a conductivity of less than 5 W/mK, therefore the hot",
"like to switch to a glass bed and to rework my printer to",
"to use the old heating resistor placed only in the centre? this way",
"to increase the printing area to 20 cm (22x22 cm glass plate). Would",
"printer (printing area: 12x12 cm). I would like to switch to a glass",
"heating resistor placed only in the centre? this way I would have a",
"a smaller heated bed for ABS and a bigger one for PLA. Would",
"cm heating resistor from my current printer (printing area: 12x12 cm). I would",
"This is because glass has a conductivity of less than 5 W/mK, therefore",
"stay hot and basically never really spread the heat to the surrounding area.",
"the heat to the surrounding area. So the frame will be cold and",
"it be possible to use the old heating resistor placed only in the",
"to switch to a glass bed and to rework my printer to increase",
"I would have a smaller heated bed for ABS and a bigger one",
"less than 5 W/mK, therefore the hot area will stay hot and basically",
"15x15 cm heating resistor from my current printer (printing area: 12x12 cm). I",
"W/mK, therefore the hot area will stay hot and basically never really spread",
"I would like to switch to a glass bed and to rework my",
"from my current printer (printing area: 12x12 cm). I would like to switch",
"a conductivity of less than 5 W/mK, therefore the hot area will stay",
"So the frame will be cold and the center hot, causing stresses. Related:",
"my current printer (printing area: 12x12 cm). I would like to switch to",
"current printer (printing area: 12x12 cm). I would like to switch to a",
"to a glass bed and to rework my printer to increase the printing",
"area will stay hot and basically never really spread the heat to the",
"heated bed for ABS and a bigger one for PLA. Would the glass",
"have a 15x15 cm heating resistor from my current printer (printing area: 12x12",
"area to 20 cm (22x22 cm glass plate). Would it be possible to",
"20 cm (22x22 cm glass plate). Would it be possible to use the",
"the surrounding area. So the frame will be cold and the center hot,",
"to the surrounding area. So the frame will be cold and the center",
"really spread the heat to the surrounding area. So the frame will be",
"would like to switch to a glass bed and to rework my printer",
"therefore the hot area will stay hot and basically never really spread the",
"the glass crack due to non uniform heating? This is because glass has",
"crack due to non uniform heating? This is because glass has a conductivity",
"conductivity of less than 5 W/mK, therefore the hot area will stay hot",
"for ABS and a bigger one for PLA. Would the glass crack due",
"way I would have a smaller heated bed for ABS and a bigger",
"spread the heat to the surrounding area. So the frame will be cold",
"heat to the surrounding area. So the frame will be cold and the",
"heating? This is because glass has a conductivity of less than 5 W/mK,",
"5 W/mK, therefore the hot area will stay hot and basically never really",
"resistor from my current printer (printing area: 12x12 cm). I would like to",
"area. So the frame will be cold and the center hot, causing stresses.",
"a 15x15 cm heating resistor from my current printer (printing area: 12x12 cm).",
"to rework my printer to increase the printing area to 20 cm (22x22",
"the old heating resistor placed only in the centre? this way I would",
"the frame will be cold and the center hot, causing stresses. Related: <https://engineering.stackexchange.com/questions/31842/how-much-an-unevenly-heated-glass-plate-bows>",
"printing area to 20 cm (22x22 cm glass plate). Would it be possible",
"and basically never really spread the heat to the surrounding area. So the",
"plate). Would it be possible to use the old heating resistor placed only",
"Would it be possible to use the old heating resistor placed only in",
"PLA. Would the glass crack due to non uniform heating? This is because",
"is because glass has a conductivity of less than 5 W/mK, therefore the",
"only in the centre? this way I would have a smaller heated bed",
"the centre? this way I would have a smaller heated bed for ABS",
"due to non uniform heating? This is because glass has a conductivity of",
"glass has a conductivity of less than 5 W/mK, therefore the hot area",
"has a conductivity of less than 5 W/mK, therefore the hot area will",
"cm (22x22 cm glass plate). Would it be possible to use the old",
"this way I would have a smaller heated bed for ABS and a",
"12x12 cm). I would like to switch to a glass bed and to",
"resistor placed only in the centre? this way I would have a smaller",
"my printer to increase the printing area to 20 cm (22x22 cm glass",
"old heating resistor placed only in the centre? this way I would have",
"will stay hot and basically never really spread the heat to the surrounding",
"to 20 cm (22x22 cm glass plate). Would it be possible to use",
"one for PLA. Would the glass crack due to non uniform heating? This",
"and a bigger one for PLA. Would the glass crack due to non",
"in the centre? this way I would have a smaller heated bed for",
"a glass bed and to rework my printer to increase the printing area",
"heating resistor from my current printer (printing area: 12x12 cm). I would like",
"to non uniform heating? This is because glass has a conductivity of less",
"glass bed and to rework my printer to increase the printing area to",
"and to rework my printer to increase the printing area to 20 cm",
"printer to increase the printing area to 20 cm (22x22 cm glass plate).",
"bigger one for PLA. Would the glass crack due to non uniform heating?",
"for PLA. Would the glass crack due to non uniform heating? This is"
] |
[
"find the zoffset M851 Z-0.59 M500 M211 S1 ``` And `G29` before printing.",
"offsets and its working good now. I was looking through Marlin G-code page",
"Does it add the Z offset to the offset of the `G29` mesh?",
"offset of the `G29` mesh? or the `G29` value replaces the `M851`? My",
"offset to 0 and let `G29` get the mesh offsets and its working",
"0 and let `G29` get the mesh offsets and its working good now.",
"A8 with Marlin firmware, I was having issues with the autoleveling sensor and",
"offset to the offset of the `G29` mesh? or the `G29` value replaces",
"add the Z offset to the offset of the `G29` mesh? or the",
"offset (`M851`) work with an auto leveling sensor? Does it add the Z",
"the offset of the `G29` mesh? or the `G29` value replaces the `M851`?",
"the `G29` mesh? or the `G29` value replaces the `M851`? My printer is",
"and its working good now. I was looking through Marlin G-code page but",
"working good now. I was looking through Marlin G-code page but couldn't figure",
";turned endstops off and got a paper to find the zoffset M851 Z-0.59",
"was having issues with the autoleveling sensor and reset the Z offset to",
"let `G29` get the mesh offsets and its working good now. I was",
"`G29` mesh? or the `G29` value replaces the `M851`? My printer is an",
"now. I was looking through Marlin G-code page but couldn't figure out how",
"Marlin G-code page but couldn't figure out how `G29` affects `M851` or vice-versa.",
"replaces the `M851`? My printer is an Anet A8 with Marlin firmware, I",
"auto leveling sensor? Does it add the Z offset to the offset of",
"how `G29` affects `M851` or vice-versa. My setup with level issues: ``` M851",
"mesh? or the `G29` value replaces the `M851`? My printer is an Anet",
"to find the zoffset M851 Z-0.59 M500 M211 S1 ``` And `G29` before",
"off and got a paper to find the zoffset M851 Z-0.59 M500 M211",
"M211 S0 ;turned endstops off and got a paper to find the zoffset",
"setup with level issues: ``` M851 Z0 G28 M211 S0 ;turned endstops off",
"mesh offsets and its working good now. I was looking through Marlin G-code",
"page but couldn't figure out how `G29` affects `M851` or vice-versa. My setup",
"Z0 G28 M211 S0 ;turned endstops off and got a paper to find",
"it add the Z offset to the offset of the `G29` mesh? or",
"looking through Marlin G-code page but couldn't figure out how `G29` affects `M851`",
"its working good now. I was looking through Marlin G-code page but couldn't",
"and got a paper to find the zoffset M851 Z-0.59 M500 M211 S1",
"an Anet A8 with Marlin firmware, I was having issues with the autoleveling",
"affects `M851` or vice-versa. My setup with level issues: ``` M851 Z0 G28",
"autoleveling sensor and reset the Z offset to 0 and let `G29` get",
"to 0 and let `G29` get the mesh offsets and its working good",
"reset the Z offset to 0 and let `G29` get the mesh offsets",
"How does Z offset (`M851`) work with an auto leveling sensor? Does it",
"Anet A8 with Marlin firmware, I was having issues with the autoleveling sensor",
"and reset the Z offset to 0 and let `G29` get the mesh",
"a paper to find the zoffset M851 Z-0.59 M500 M211 S1 ``` And",
"endstops off and got a paper to find the zoffset M851 Z-0.59 M500",
"``` M851 Z0 G28 M211 S0 ;turned endstops off and got a paper",
"and let `G29` get the mesh offsets and its working good now. I",
"`M851`? My printer is an Anet A8 with Marlin firmware, I was having",
"sensor and reset the Z offset to 0 and let `G29` get the",
"M851 Z0 G28 M211 S0 ;turned endstops off and got a paper to",
"but couldn't figure out how `G29` affects `M851` or vice-versa. My setup with",
"the `G29` value replaces the `M851`? My printer is an Anet A8 with",
"an auto leveling sensor? Does it add the Z offset to the offset",
"the mesh offsets and its working good now. I was looking through Marlin",
"out how `G29` affects `M851` or vice-versa. My setup with level issues: ```",
"the Z offset to 0 and let `G29` get the mesh offsets and",
"through Marlin G-code page but couldn't figure out how `G29` affects `M851` or",
"S0 ;turned endstops off and got a paper to find the zoffset M851",
"level issues: ``` M851 Z0 G28 M211 S0 ;turned endstops off and got",
"G28 M211 S0 ;turned endstops off and got a paper to find the",
"of the `G29` mesh? or the `G29` value replaces the `M851`? My printer",
"leveling sensor? Does it add the Z offset to the offset of the",
"with an auto leveling sensor? Does it add the Z offset to the",
"firmware, I was having issues with the autoleveling sensor and reset the Z",
"good now. I was looking through Marlin G-code page but couldn't figure out",
"value replaces the `M851`? My printer is an Anet A8 with Marlin firmware,",
"couldn't figure out how `G29` affects `M851` or vice-versa. My setup with level",
"(`M851`) work with an auto leveling sensor? Does it add the Z offset",
"printer is an Anet A8 with Marlin firmware, I was having issues with",
"get the mesh offsets and its working good now. I was looking through",
"with Marlin firmware, I was having issues with the autoleveling sensor and reset",
"or the `G29` value replaces the `M851`? My printer is an Anet A8",
"`M851` or vice-versa. My setup with level issues: ``` M851 Z0 G28 M211",
"issues with the autoleveling sensor and reset the Z offset to 0 and",
"figure out how `G29` affects `M851` or vice-versa. My setup with level issues:",
"My printer is an Anet A8 with Marlin firmware, I was having issues",
"paper to find the zoffset M851 Z-0.59 M500 M211 S1 ``` And `G29`",
"`G29` get the mesh offsets and its working good now. I was looking",
"the Z offset to the offset of the `G29` mesh? or the `G29`",
"`G29` value replaces the `M851`? My printer is an Anet A8 with Marlin",
"with the autoleveling sensor and reset the Z offset to 0 and let",
"to the offset of the `G29` mesh? or the `G29` value replaces the",
"`G29` affects `M851` or vice-versa. My setup with level issues: ``` M851 Z0",
"sensor? Does it add the Z offset to the offset of the `G29`",
"G-code page but couldn't figure out how `G29` affects `M851` or vice-versa. My",
"vice-versa. My setup with level issues: ``` M851 Z0 G28 M211 S0 ;turned",
"Marlin firmware, I was having issues with the autoleveling sensor and reset the",
"My setup with level issues: ``` M851 Z0 G28 M211 S0 ;turned endstops",
"got a paper to find the zoffset M851 Z-0.59 M500 M211 S1 ```",
"Z offset to 0 and let `G29` get the mesh offsets and its",
"does Z offset (`M851`) work with an auto leveling sensor? Does it add",
"I was having issues with the autoleveling sensor and reset the Z offset",
"I was looking through Marlin G-code page but couldn't figure out how `G29`",
"Z offset to the offset of the `G29` mesh? or the `G29` value",
"is an Anet A8 with Marlin firmware, I was having issues with the",
"Z offset (`M851`) work with an auto leveling sensor? Does it add the",
"was looking through Marlin G-code page but couldn't figure out how `G29` affects",
"work with an auto leveling sensor? Does it add the Z offset to",
"the autoleveling sensor and reset the Z offset to 0 and let `G29`",
"issues: ``` M851 Z0 G28 M211 S0 ;turned endstops off and got a",
"with level issues: ``` M851 Z0 G28 M211 S0 ;turned endstops off and",
"the `M851`? My printer is an Anet A8 with Marlin firmware, I was",
"having issues with the autoleveling sensor and reset the Z offset to 0",
"or vice-versa. My setup with level issues: ``` M851 Z0 G28 M211 S0"
] |
[
"it took longer to make). My one concern is the lithium ion battery.",
"heated bed of 40 degrees Celsius, and a heated extruder at 240 degrees",
"g-code line during the pause? Will this affect the remainder of the print",
"make). My one concern is the lithium ion battery. Right now I'm printing",
"a heated extruder at 240 degrees Celsius, there seems to be a significant",
"of 40 degrees Celsius, and a heated extruder at 240 degrees Celsius, there",
"have I been missing out... One feature Ultimaker Cura implemented that I've been",
"printing in TPU. With a heated bed of 40 degrees Celsius, and a",
"through a 1–2 mm of insulation and cause an explosion? Anyone know how",
"Like it would probably burn my house down, and I would be asleep",
"temperature above 60 degrees Celsius (damaging the cell, causing a potential explosion). Granted,",
"device would look a lot more professional (even if it took longer to",
"and cause an explosion? Anyone know how heat travels from the initial, liquid",
"snap together looks a lot worse than printing a single piece. If I",
"structure?** Any more advice or things I should consider before pursuing this? A",
"what \"60 degrees Celsius\" actually means. It could mean only one part of",
"this. In either case, the numbers don't look good. On the other hand,",
"actually pass heat through a 1–2 mm of insulation and cause an explosion?",
"is the lithium ion battery. Right now I'm printing in TPU. With a",
"asleep when it happened. **Does anyone have any experience doing this? Is there",
"ago and finally downloaded Ultimaker's version of Cura... Boy... have I been missing",
"should consider before pursuing this? A more specific pause type might be helpful,",
"40 degrees Celsius, and a heated extruder at 240 degrees Celsius, there seems",
"doing this? Is there a way to turn off the heated bed mid-print?",
"obviously, an explosion would be really really bad. Like it would probably burn",
"explosion? Anyone know how heat travels from the initial, liquid print material through",
"to make). My one concern is the lithium ion battery. Right now I'm",
"Cura implemented that I've been looking for is a \"pause at z-height\" feature",
"bad. Like it would probably burn my house down, and I would be",
"missing out... One feature Ultimaker Cura implemented that I've been looking for is",
"don't look good. On the other hand, the heated bed surely doesn't need",
"Lulzbot Mini a couple months ago and finally downloaded Ultimaker's version of Cura...",
"mean only one part of the packaging needs to reach this temperature, or",
"the extruder actually pass heat through a 1–2 mm of insulation and cause",
"Am I being paranoid? Can the extruder actually pass heat through a 1–2",
"sure what \"60 degrees Celsius\" actually means. It could mean only one part",
"insulative TPU before the rest of the device. I think the print would",
"would probably burn my house down, and I would be asleep when it",
"a 1–2 mm of insulation and cause an explosion? Anyone know how heat",
"electronics device, and creating two pieces that snap together looks a lot worse",
"line during the pause? Will this affect the remainder of the print you",
"am not sure what \"60 degrees Celsius\" actually means. It could mean only",
"things I should consider before pursuing this? A more specific pause type might",
"paranoid? Can the extruder actually pass heat through a 1–2 mm of insulation",
"months ago and finally downloaded Ultimaker's version of Cura... Boy... have I been",
"actually means. It could mean only one part of the packaging needs to",
"create a \"roof\" for the LiIon battery that I can slip it under,",
"more professional (even if it took longer to make). My one concern is",
"this? A more specific pause type might be helpful, if anyone knows of",
"other hand, the heated bed surely doesn't need to remain heated beyond the",
"need to remain heated beyond the first few layers? Additionally, I can create",
"I would be asleep when it happened. **Does anyone have any experience doing",
"before the rest of the device. I think the print would happen safely",
"a temperature above 60 degrees Celsius (damaging the cell, causing a potential explosion).",
"the print would happen safely like this, but obviously, an explosion would be",
"the heated bed mid-print? I guess I can insert a g-code line during",
"burn my house down, and I would be asleep when it happened. **Does",
"downloaded Ultimaker's version of Cura... Boy... have I been missing out... One feature",
"Mini a couple months ago and finally downloaded Ultimaker's version of Cura... Boy...",
"Additionally, I can create a \"roof\" for the LiIon battery that I can",
"initial, liquid print material through the rest of the structure?** Any more advice",
"surely doesn't need to remain heated beyond the first few layers? Additionally, I",
"not sure what \"60 degrees Celsius\" actually means. It could mean only one",
"or things I should consider before pursuing this? A more specific pause type",
"1–2 mm of insulation and cause an explosion? Anyone know how heat travels",
"think? Am I being paranoid? Can the extruder actually pass heat through a",
"bed of 40 degrees Celsius, and a heated extruder at 240 degrees Celsius,",
"hand, the heated bed surely doesn't need to remain heated beyond the first",
"lot worse than printing a single piece. If I could pause my print,",
"Can the extruder actually pass heat through a 1–2 mm of insulation and",
"when it happened. **Does anyone have any experience doing this? Is there a",
"**Does anyone have any experience doing this? Is there a way to turn",
"that the lithium ion battery reaches a temperature above 60 degrees Celsius (damaging",
"doesn't need to remain heated beyond the first few layers? Additionally, I can",
"\"pause at z-height\" feature (\"post-processing tool\"). I'm building prototypes of an electronics device,",
"a heated bed of 40 degrees Celsius, and a heated extruder at 240",
"\"60 degrees Celsius\" actually means. It could mean only one part of the",
"ion battery reaches a temperature above 60 degrees Celsius (damaging the cell, causing",
"entire LiPo's internal temperature would need to reach this. In either case, the",
"60 degrees Celsius (damaging the cell, causing a potential explosion). Granted, I am",
"either case, the numbers don't look good. On the other hand, the heated",
"experience doing this? Is there a way to turn off the heated bed",
"finally downloaded Ultimaker's version of Cura... Boy... have I been missing out... One",
"degrees Celsius\" actually means. It could mean only one part of the packaging",
"providing some insulative TPU before the rest of the device. I think the",
"reach this temperature, or it could mean the entire LiPo's internal temperature would",
"extruder actually pass heat through a 1–2 mm of insulation and cause an",
"it could mean the entire LiPo's internal temperature would need to reach this.",
"together looks a lot worse than printing a single piece. If I could",
"and continue printing, my device would look a lot more professional (even if",
"cause an explosion? Anyone know how heat travels from the initial, liquid print",
"from the initial, liquid print material through the rest of the structure?** Any",
"my house down, and I would be asleep when it happened. **Does anyone",
"that I've been looking for is a \"pause at z-height\" feature (\"post-processing tool\").",
"pass heat through a 1–2 mm of insulation and cause an explosion? Anyone",
"think the print would happen safely like this, but obviously, an explosion would",
"two pieces that snap together looks a lot worse than printing a single",
"good. On the other hand, the heated bed surely doesn't need to remain",
"would need to reach this. In either case, the numbers don't look good.",
"My one concern is the lithium ion battery. Right now I'm printing in",
"that snap together looks a lot worse than printing a single piece. If",
"the rest of the device. I think the print would happen safely like",
"a Lulzbot Mini a couple months ago and finally downloaded Ultimaker's version of",
"(\"post-processing tool\"). I'm building prototypes of an electronics device, and creating two pieces",
"Is there a way to turn off the heated bed mid-print? I guess",
"LiIon battery that I can slip it under, providing some insulative TPU before",
"and I would be asleep when it happened. **Does anyone have any experience",
"mid-print? I guess I can insert a g-code line during the pause? Will",
"Right now I'm printing in TPU. With a heated bed of 40 degrees",
"electronics, and continue printing, my device would look a lot more professional (even",
"liquid print material through the rest of the structure?** Any more advice or",
"safely like this, but obviously, an explosion would be really really bad. Like",
"the device. I think the print would happen safely like this, but obviously,",
"insert a g-code line during the pause? Will this affect the remainder of",
"Will this affect the remainder of the print you think? Am I being",
"print you think? Am I being paranoid? Can the extruder actually pass heat",
"insert my electronics, and continue printing, my device would look a lot more",
"I bought a Lulzbot Mini a couple months ago and finally downloaded Ultimaker's",
"to remain heated beyond the first few layers? Additionally, I can create a",
"my electronics, and continue printing, my device would look a lot more professional",
"like this, but obviously, an explosion would be really really bad. Like it",
"this affect the remainder of the print you think? Am I being paranoid?",
"numbers don't look good. On the other hand, the heated bed surely doesn't",
"feature (\"post-processing tool\"). I'm building prototypes of an electronics device, and creating two",
"longer to make). My one concern is the lithium ion battery. Right now",
"or it could mean the entire LiPo's internal temperature would need to reach",
"heated bed surely doesn't need to remain heated beyond the first few layers?",
"an explosion? Anyone know how heat travels from the initial, liquid print material",
"one concern is the lithium ion battery. Right now I'm printing in TPU.",
"It could mean only one part of the packaging needs to reach this",
"(even if it took longer to make). My one concern is the lithium",
"how heat travels from the initial, liquid print material through the rest of",
"remainder of the print you think? Am I being paranoid? Can the extruder",
"my print, insert my electronics, and continue printing, my device would look a",
"worse than printing a single piece. If I could pause my print, insert",
"mm of insulation and cause an explosion? Anyone know how heat travels from",
"would be really really bad. Like it would probably burn my house down,",
"I can slip it under, providing some insulative TPU before the rest of",
"Celsius, and a heated extruder at 240 degrees Celsius, there seems to be",
"\"roof\" for the LiIon battery that I can slip it under, providing some",
"a potential explosion). Granted, I am not sure what \"60 degrees Celsius\" actually",
"look a lot more professional (even if it took longer to make). My",
"under, providing some insulative TPU before the rest of the device. I think",
"I think the print would happen safely like this, but obviously, an explosion",
"could mean the entire LiPo's internal temperature would need to reach this. In",
"With a heated bed of 40 degrees Celsius, and a heated extruder at",
"turn off the heated bed mid-print? I guess I can insert a g-code",
"happened. **Does anyone have any experience doing this? Is there a way to",
"more advice or things I should consider before pursuing this? A more specific",
"temperature, or it could mean the entire LiPo's internal temperature would need to",
"the first few layers? Additionally, I can create a \"roof\" for the LiIon",
"this temperature, or it could mean the entire LiPo's internal temperature would need",
"reaches a temperature above 60 degrees Celsius (damaging the cell, causing a potential",
"layers? Additionally, I can create a \"roof\" for the LiIon battery that I",
"than printing a single piece. If I could pause my print, insert my",
"there a way to turn off the heated bed mid-print? I guess I",
"remain heated beyond the first few layers? Additionally, I can create a \"roof\"",
"a way to turn off the heated bed mid-print? I guess I can",
"travels from the initial, liquid print material through the rest of the structure?**",
"TPU before the rest of the device. I think the print would happen",
"feature Ultimaker Cura implemented that I've been looking for is a \"pause at",
"internal temperature would need to reach this. In either case, the numbers don't",
"the cell, causing a potential explosion). Granted, I am not sure what \"60",
"In either case, the numbers don't look good. On the other hand, the",
"the LiIon battery that I can slip it under, providing some insulative TPU",
"ion battery. Right now I'm printing in TPU. With a heated bed of",
"printing a single piece. If I could pause my print, insert my electronics,",
"Celsius\" actually means. It could mean only one part of the packaging needs",
"of insulation and cause an explosion? Anyone know how heat travels from the",
"been missing out... One feature Ultimaker Cura implemented that I've been looking for",
"degrees Celsius, and a heated extruder at 240 degrees Celsius, there seems to",
"I've been looking for is a \"pause at z-height\" feature (\"post-processing tool\"). I'm",
"piece. If I could pause my print, insert my electronics, and continue printing,",
"case, the numbers don't look good. On the other hand, the heated bed",
"of Cura... Boy... have I been missing out... One feature Ultimaker Cura implemented",
"battery. Right now I'm printing in TPU. With a heated bed of 40",
"the numbers don't look good. On the other hand, the heated bed surely",
"Ultimaker's version of Cura... Boy... have I been missing out... One feature Ultimaker",
"could mean only one part of the packaging needs to reach this temperature,",
"the remainder of the print you think? Am I being paranoid? Can the",
"240 degrees Celsius, there seems to be a significant risk that the lithium",
"the lithium ion battery. Right now I'm printing in TPU. With a heated",
"explosion). Granted, I am not sure what \"60 degrees Celsius\" actually means. It",
"is a \"pause at z-height\" feature (\"post-processing tool\"). I'm building prototypes of an",
"would look a lot more professional (even if it took longer to make).",
"rest of the device. I think the print would happen safely like this,",
"to be a significant risk that the lithium ion battery reaches a temperature",
"pieces that snap together looks a lot worse than printing a single piece.",
"you think? Am I being paranoid? Can the extruder actually pass heat through",
"needs to reach this temperature, or it could mean the entire LiPo's internal",
"heated bed mid-print? I guess I can insert a g-code line during the",
"bought a Lulzbot Mini a couple months ago and finally downloaded Ultimaker's version",
"of the structure?** Any more advice or things I should consider before pursuing",
"I'm building prototypes of an electronics device, and creating two pieces that snap",
"the other hand, the heated bed surely doesn't need to remain heated beyond",
"pause my print, insert my electronics, and continue printing, my device would look",
"the rest of the structure?** Any more advice or things I should consider",
"in TPU. With a heated bed of 40 degrees Celsius, and a heated",
"bed mid-print? I guess I can insert a g-code line during the pause?",
"looking for is a \"pause at z-height\" feature (\"post-processing tool\"). I'm building prototypes",
"the structure?** Any more advice or things I should consider before pursuing this?",
"significant risk that the lithium ion battery reaches a temperature above 60 degrees",
"one part of the packaging needs to reach this temperature, or it could",
"I being paranoid? Can the extruder actually pass heat through a 1–2 mm",
"consider before pursuing this? A more specific pause type might be helpful, if",
"some insulative TPU before the rest of the device. I think the print",
"professional (even if it took longer to make). My one concern is the",
"risk that the lithium ion battery reaches a temperature above 60 degrees Celsius",
"really really bad. Like it would probably burn my house down, and I",
"of the print you think? Am I being paranoid? Can the extruder actually",
"I can create a \"roof\" for the LiIon battery that I can slip",
"print material through the rest of the structure?** Any more advice or things",
"first few layers? Additionally, I can create a \"roof\" for the LiIon battery",
"a g-code line during the pause? Will this affect the remainder of the",
"I should consider before pursuing this? A more specific pause type might be",
"lithium ion battery. Right now I'm printing in TPU. With a heated bed",
"the lithium ion battery reaches a temperature above 60 degrees Celsius (damaging the",
"building prototypes of an electronics device, and creating two pieces that snap together",
"part of the packaging needs to reach this temperature, or it could mean",
"Any more advice or things I should consider before pursuing this? A more",
"creating two pieces that snap together looks a lot worse than printing a",
"would happen safely like this, but obviously, an explosion would be really really",
"a lot worse than printing a single piece. If I could pause my",
"look good. On the other hand, the heated bed surely doesn't need to",
"there seems to be a significant risk that the lithium ion battery reaches",
"the print you think? Am I being paranoid? Can the extruder actually pass",
"being paranoid? Can the extruder actually pass heat through a 1–2 mm of",
"took longer to make). My one concern is the lithium ion battery. Right",
"few layers? Additionally, I can create a \"roof\" for the LiIon battery that",
"a lot more professional (even if it took longer to make). My one",
"extruder at 240 degrees Celsius, there seems to be a significant risk that",
"cell, causing a potential explosion). Granted, I am not sure what \"60 degrees",
"know how heat travels from the initial, liquid print material through the rest",
"On the other hand, the heated bed surely doesn't need to remain heated",
"I'm printing in TPU. With a heated bed of 40 degrees Celsius, and",
"and creating two pieces that snap together looks a lot worse than printing",
"TPU. With a heated bed of 40 degrees Celsius, and a heated extruder",
"my device would look a lot more professional (even if it took longer",
"now I'm printing in TPU. With a heated bed of 40 degrees Celsius,",
"happen safely like this, but obviously, an explosion would be really really bad.",
"degrees Celsius (damaging the cell, causing a potential explosion). Granted, I am not",
"potential explosion). Granted, I am not sure what \"60 degrees Celsius\" actually means.",
"battery reaches a temperature above 60 degrees Celsius (damaging the cell, causing a",
"can create a \"roof\" for the LiIon battery that I can slip it",
"slip it under, providing some insulative TPU before the rest of the device.",
"lot more professional (even if it took longer to make). My one concern",
"version of Cura... Boy... have I been missing out... One feature Ultimaker Cura",
"Celsius, there seems to be a significant risk that the lithium ion battery",
"reach this. In either case, the numbers don't look good. On the other",
"looks a lot worse than printing a single piece. If I could pause",
"the pause? Will this affect the remainder of the print you think? Am",
"prototypes of an electronics device, and creating two pieces that snap together looks",
"LiPo's internal temperature would need to reach this. In either case, the numbers",
"insulation and cause an explosion? Anyone know how heat travels from the initial,",
"I can insert a g-code line during the pause? Will this affect the",
"off the heated bed mid-print? I guess I can insert a g-code line",
"that I can slip it under, providing some insulative TPU before the rest",
"temperature would need to reach this. In either case, the numbers don't look",
"down, and I would be asleep when it happened. **Does anyone have any",
"been looking for is a \"pause at z-height\" feature (\"post-processing tool\"). I'm building",
"Granted, I am not sure what \"60 degrees Celsius\" actually means. It could",
"an explosion would be really really bad. Like it would probably burn my",
"z-height\" feature (\"post-processing tool\"). I'm building prototypes of an electronics device, and creating",
"pause? Will this affect the remainder of the print you think? Am I",
"of the packaging needs to reach this temperature, or it could mean the",
"battery that I can slip it under, providing some insulative TPU before the",
"any experience doing this? Is there a way to turn off the heated",
"and finally downloaded Ultimaker's version of Cura... Boy... have I been missing out...",
"heat through a 1–2 mm of insulation and cause an explosion? Anyone know",
"it happened. **Does anyone have any experience doing this? Is there a way",
"and a heated extruder at 240 degrees Celsius, there seems to be a",
"need to reach this. In either case, the numbers don't look good. On",
"explosion would be really really bad. Like it would probably burn my house",
"single piece. If I could pause my print, insert my electronics, and continue",
"if it took longer to make). My one concern is the lithium ion",
"Ultimaker Cura implemented that I've been looking for is a \"pause at z-height\"",
"really bad. Like it would probably burn my house down, and I would",
"have any experience doing this? Is there a way to turn off the",
"So I bought a Lulzbot Mini a couple months ago and finally downloaded",
"device, and creating two pieces that snap together looks a lot worse than",
"Celsius (damaging the cell, causing a potential explosion). Granted, I am not sure",
"at 240 degrees Celsius, there seems to be a significant risk that the",
"a couple months ago and finally downloaded Ultimaker's version of Cura... Boy... have",
"seems to be a significant risk that the lithium ion battery reaches a",
"of the device. I think the print would happen safely like this, but",
"I could pause my print, insert my electronics, and continue printing, my device",
"to turn off the heated bed mid-print? I guess I can insert a",
"I guess I can insert a g-code line during the pause? Will this",
"I been missing out... One feature Ultimaker Cura implemented that I've been looking",
"can insert a g-code line during the pause? Will this affect the remainder",
"affect the remainder of the print you think? Am I being paranoid? Can",
"for is a \"pause at z-height\" feature (\"post-processing tool\"). I'm building prototypes of",
"If I could pause my print, insert my electronics, and continue printing, my",
"(damaging the cell, causing a potential explosion). Granted, I am not sure what",
"be a significant risk that the lithium ion battery reaches a temperature above",
"probably burn my house down, and I would be asleep when it happened.",
"couple months ago and finally downloaded Ultimaker's version of Cura... Boy... have I",
"the initial, liquid print material through the rest of the structure?** Any more",
"before pursuing this? A more specific pause type might be helpful, if anyone",
"implemented that I've been looking for is a \"pause at z-height\" feature (\"post-processing",
"guess I can insert a g-code line during the pause? Will this affect",
"out... One feature Ultimaker Cura implemented that I've been looking for is a",
"to reach this temperature, or it could mean the entire LiPo's internal temperature",
"print, insert my electronics, and continue printing, my device would look a lot",
"of an electronics device, and creating two pieces that snap together looks a",
"for the LiIon battery that I can slip it under, providing some insulative",
"this, but obviously, an explosion would be really really bad. Like it would",
"rest of the structure?** Any more advice or things I should consider before",
"heat travels from the initial, liquid print material through the rest of the",
"above 60 degrees Celsius (damaging the cell, causing a potential explosion). Granted, I",
"Boy... have I been missing out... One feature Ultimaker Cura implemented that I've",
"One feature Ultimaker Cura implemented that I've been looking for is a \"pause",
"concern is the lithium ion battery. Right now I'm printing in TPU. With",
"an electronics device, and creating two pieces that snap together looks a lot",
"through the rest of the structure?** Any more advice or things I should",
"beyond the first few layers? Additionally, I can create a \"roof\" for the",
"continue printing, my device would look a lot more professional (even if it",
"it under, providing some insulative TPU before the rest of the device. I",
"the entire LiPo's internal temperature would need to reach this. In either case,",
"a \"roof\" for the LiIon battery that I can slip it under, providing",
"mean the entire LiPo's internal temperature would need to reach this. In either",
"this? Is there a way to turn off the heated bed mid-print? I",
"Cura... Boy... have I been missing out... One feature Ultimaker Cura implemented that",
"house down, and I would be asleep when it happened. **Does anyone have",
"but obviously, an explosion would be really really bad. Like it would probably",
"a \"pause at z-height\" feature (\"post-processing tool\"). I'm building prototypes of an electronics",
"can slip it under, providing some insulative TPU before the rest of the",
"print would happen safely like this, but obviously, an explosion would be really",
"the packaging needs to reach this temperature, or it could mean the entire",
"tool\"). I'm building prototypes of an electronics device, and creating two pieces that",
"a single piece. If I could pause my print, insert my electronics, and",
"could pause my print, insert my electronics, and continue printing, my device would",
"lithium ion battery reaches a temperature above 60 degrees Celsius (damaging the cell,",
"Anyone know how heat travels from the initial, liquid print material through the",
"at z-height\" feature (\"post-processing tool\"). I'm building prototypes of an electronics device, and",
"means. It could mean only one part of the packaging needs to reach",
"be asleep when it happened. **Does anyone have any experience doing this? Is",
"advice or things I should consider before pursuing this? A more specific pause",
"the heated bed surely doesn't need to remain heated beyond the first few",
"I am not sure what \"60 degrees Celsius\" actually means. It could mean",
"packaging needs to reach this temperature, or it could mean the entire LiPo's",
"a significant risk that the lithium ion battery reaches a temperature above 60",
"heated beyond the first few layers? Additionally, I can create a \"roof\" for",
"material through the rest of the structure?** Any more advice or things I",
"to reach this. In either case, the numbers don't look good. On the",
"way to turn off the heated bed mid-print? I guess I can insert",
"bed surely doesn't need to remain heated beyond the first few layers? Additionally,",
"would be asleep when it happened. **Does anyone have any experience doing this?",
"causing a potential explosion). Granted, I am not sure what \"60 degrees Celsius\"",
"heated extruder at 240 degrees Celsius, there seems to be a significant risk",
"it would probably burn my house down, and I would be asleep when",
"degrees Celsius, there seems to be a significant risk that the lithium ion",
"anyone have any experience doing this? Is there a way to turn off",
"A more specific pause type might be helpful, if anyone knows of any.",
"be really really bad. Like it would probably burn my house down, and",
"printing, my device would look a lot more professional (even if it took",
"pursuing this? A more specific pause type might be helpful, if anyone knows",
"only one part of the packaging needs to reach this temperature, or it",
"device. I think the print would happen safely like this, but obviously, an",
"during the pause? Will this affect the remainder of the print you think?"
] |
[
"about coding it? Are there programs that automatically calibrate all the motors? Can",
"aspects, gcode, stepper motor moment, axis zeroing, etc; but if I am to",
"printing aspect of the build as I realize that CNC's and laser engravers",
"the project. I currently own a 3D printer and am familiar with some",
"Since all use a standard Cartesian axis I wanted to be able to",
"do you go about coding it? Are there programs that automatically calibrate all",
"a new printing program from scratch that can read gcode? For simplicity lets",
"currently own a 3D printer and am familiar with some of the coding",
"of the coding aspects, gcode, stepper motor moment, axis zeroing, etc; but if",
"a 3 axis system how do you go about coding it? Are there",
"the motors? Can I take existing 3D printer programs and adjust the stepper",
"a 3D printer and am familiar with some of the coding aspects, gcode,",
"system how do you go about coding it? Are there programs that automatically",
"out tool heads depending on the purpose. I have everything thought out except",
"the printing aspect of the build as I realize that CNC's and laser",
"aspect of the project. I currently own a 3D printer and am familiar",
"lets just talk about the printing aspect of the build as I realize",
"able to swap out tool heads depending on the purpose. I have everything",
"motor values and build plate area? or do I have to code a",
"to code a new printing program from scratch that can read gcode? For",
"tool heads depending on the purpose. I have everything thought out except the",
"motors? Can I take existing 3D printer programs and adjust the stepper motor",
"about building my own 3D printer/Laser Engraver/CNC. Since all use a standard Cartesian",
"thought out except the coding aspect of the project. I currently own a",
"go about coding it? Are there programs that automatically calibrate all the motors?",
"from scratch that can read gcode? For simplicity lets just talk about the",
"the coding aspect of the project. I currently own a 3D printer and",
"program from scratch that can read gcode? For simplicity lets just talk about",
"printer programs and adjust the stepper motor values and build plate area? or",
"it? Are there programs that automatically calibrate all the motors? Can I take",
"programs and adjust the stepper motor values and build plate area? or do",
"code a new printing program from scratch that can read gcode? For simplicity",
"gcode? For simplicity lets just talk about the printing aspect of the build",
"printing program from scratch that can read gcode? For simplicity lets just talk",
"my own 3D printer/Laser Engraver/CNC. Since all use a standard Cartesian axis I",
"zeroing, etc; but if I am to build a 3 axis system how",
"calibrate all the motors? Can I take existing 3D printer programs and adjust",
"3D printer programs and adjust the stepper motor values and build plate area?",
"build plate area? or do I have to code a new printing program",
"the stepper motor values and build plate area? or do I have to",
"you go about coding it? Are there programs that automatically calibrate all the",
"wanted to be able to swap out tool heads depending on the purpose.",
"simplicity lets just talk about the printing aspect of the build as I",
"or do I have to code a new printing program from scratch that",
"of the build as I realize that CNC's and laser engravers work on",
"and am familiar with some of the coding aspects, gcode, stepper motor moment,",
"am familiar with some of the coding aspects, gcode, stepper motor moment, axis",
"as I realize that CNC's and laser engravers work on different vector systems.",
"have everything thought out except the coding aspect of the project. I currently",
"the purpose. I have everything thought out except the coding aspect of the",
"3 axis system how do you go about coding it? Are there programs",
"Are there programs that automatically calibrate all the motors? Can I take existing",
"own a 3D printer and am familiar with some of the coding aspects,",
"use a standard Cartesian axis I wanted to be able to swap out",
"if I am to build a 3 axis system how do you go",
"existing 3D printer programs and adjust the stepper motor values and build plate",
"building my own 3D printer/Laser Engraver/CNC. Since all use a standard Cartesian axis",
"I take existing 3D printer programs and adjust the stepper motor values and",
"talk about the printing aspect of the build as I realize that CNC's",
"am to build a 3 axis system how do you go about coding",
"moment, axis zeroing, etc; but if I am to build a 3 axis",
"axis system how do you go about coding it? Are there programs that",
"purpose. I have everything thought out except the coding aspect of the project.",
"just talk about the printing aspect of the build as I realize that",
"I have to code a new printing program from scratch that can read",
"to be able to swap out tool heads depending on the purpose. I",
"a standard Cartesian axis I wanted to be able to swap out tool",
"area? or do I have to code a new printing program from scratch",
"coding it? Are there programs that automatically calibrate all the motors? Can I",
"familiar with some of the coding aspects, gcode, stepper motor moment, axis zeroing,",
"build as I realize that CNC's and laser engravers work on different vector",
"some of the coding aspects, gcode, stepper motor moment, axis zeroing, etc; but",
"about the printing aspect of the build as I realize that CNC's and",
"the build as I realize that CNC's and laser engravers work on different",
"build a 3 axis system how do you go about coding it? Are",
"everything thought out except the coding aspect of the project. I currently own",
"I currently own a 3D printer and am familiar with some of the",
"coding aspects, gcode, stepper motor moment, axis zeroing, etc; but if I am",
"stepper motor moment, axis zeroing, etc; but if I am to build a",
"that automatically calibrate all the motors? Can I take existing 3D printer programs",
"adjust the stepper motor values and build plate area? or do I have",
"except the coding aspect of the project. I currently own a 3D printer",
"on the purpose. I have everything thought out except the coding aspect of",
"thinking about building my own 3D printer/Laser Engraver/CNC. Since all use a standard",
"can read gcode? For simplicity lets just talk about the printing aspect of",
"read gcode? For simplicity lets just talk about the printing aspect of the",
"depending on the purpose. I have everything thought out except the coding aspect",
"have to code a new printing program from scratch that can read gcode?",
"and build plate area? or do I have to code a new printing",
"motor moment, axis zeroing, etc; but if I am to build a 3",
"out except the coding aspect of the project. I currently own a 3D",
"programs that automatically calibrate all the motors? Can I take existing 3D printer",
"values and build plate area? or do I have to code a new",
"there programs that automatically calibrate all the motors? Can I take existing 3D",
"take existing 3D printer programs and adjust the stepper motor values and build",
"stepper motor values and build plate area? or do I have to code",
"scratch that can read gcode? For simplicity lets just talk about the printing",
"3D printer/Laser Engraver/CNC. Since all use a standard Cartesian axis I wanted to",
"For simplicity lets just talk about the printing aspect of the build as",
"I wanted to be able to swap out tool heads depending on the",
"I realize that CNC's and laser engravers work on different vector systems. Thanks",
"automatically calibrate all the motors? Can I take existing 3D printer programs and",
"realize that CNC's and laser engravers work on different vector systems. Thanks :)",
"heads depending on the purpose. I have everything thought out except the coding",
"to swap out tool heads depending on the purpose. I have everything thought",
"all use a standard Cartesian axis I wanted to be able to swap",
"standard Cartesian axis I wanted to be able to swap out tool heads",
"aspect of the build as I realize that CNC's and laser engravers work",
"be able to swap out tool heads depending on the purpose. I have",
"I have everything thought out except the coding aspect of the project. I",
"project. I currently own a 3D printer and am familiar with some of",
"axis zeroing, etc; but if I am to build a 3 axis system",
"Engraver/CNC. Since all use a standard Cartesian axis I wanted to be able",
"plate area? or do I have to code a new printing program from",
"coding aspect of the project. I currently own a 3D printer and am",
"to build a 3 axis system how do you go about coding it?",
"I am to build a 3 axis system how do you go about",
"own 3D printer/Laser Engraver/CNC. Since all use a standard Cartesian axis I wanted",
"printer and am familiar with some of the coding aspects, gcode, stepper motor",
"axis I wanted to be able to swap out tool heads depending on",
"the coding aspects, gcode, stepper motor moment, axis zeroing, etc; but if I",
"Can I take existing 3D printer programs and adjust the stepper motor values",
"how do you go about coding it? Are there programs that automatically calibrate",
"printer/Laser Engraver/CNC. Since all use a standard Cartesian axis I wanted to be",
"with some of the coding aspects, gcode, stepper motor moment, axis zeroing, etc;",
"and adjust the stepper motor values and build plate area? or do I",
"I'm thinking about building my own 3D printer/Laser Engraver/CNC. Since all use a",
"of the project. I currently own a 3D printer and am familiar with",
"all the motors? Can I take existing 3D printer programs and adjust the",
"Cartesian axis I wanted to be able to swap out tool heads depending",
"that can read gcode? For simplicity lets just talk about the printing aspect",
"etc; but if I am to build a 3 axis system how do",
"gcode, stepper motor moment, axis zeroing, etc; but if I am to build",
"new printing program from scratch that can read gcode? For simplicity lets just",
"swap out tool heads depending on the purpose. I have everything thought out",
"3D printer and am familiar with some of the coding aspects, gcode, stepper",
"but if I am to build a 3 axis system how do you",
"do I have to code a new printing program from scratch that can"
] |
[
"cloud (billions of points) of the exterior of a building obtained by laser",
"density, and I cannot print it. Is there any algorithm which could use",
"a building obtained by laser scanning it with a Leica head. I successfully",
"to print the building by first creating a mesh. I tried using CloudCompare,",
"(billions of points) of the exterior of a building obtained by laser scanning",
"mainly in the roofs which have the lowest point density, and I cannot",
"head. I successfully subsampled it down to around 500,000 and I'm trying to",
"exterior of a building obtained by laser scanning it with a Leica head.",
"Meshlab and PDAL, using Poisson surface reconstruction. However, the resulting mesh is full",
"of points) of the exterior of a building obtained by laser scanning it",
"of the exterior of a building obtained by laser scanning it with a",
"have the lowest point density, and I cannot print it. Is there any",
"could use the fact that the point cloud is precisely the exterior part",
"Leica head. I successfully subsampled it down to around 500,000 and I'm trying",
"full of holes, mainly in the roofs which have the lowest point density,",
"point cloud (billions of points) of the exterior of a building obtained by",
"that the point cloud is precisely the exterior part of a geometric thing?",
"I have a very dense point cloud (billions of points) of the exterior",
"using Poisson surface reconstruction. However, the resulting mesh is full of holes, mainly",
"PDAL, using Poisson surface reconstruction. However, the resulting mesh is full of holes,",
"the exterior of a building obtained by laser scanning it with a Leica",
"any algorithm which could use the fact that the point cloud is precisely",
"the fact that the point cloud is precisely the exterior part of a",
"using CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction. However, the resulting mesh",
"trying to print the building by first creating a mesh. I tried using",
"building by first creating a mesh. I tried using CloudCompare, Meshlab and PDAL,",
"building obtained by laser scanning it with a Leica head. I successfully subsampled",
"creating a mesh. I tried using CloudCompare, Meshlab and PDAL, using Poisson surface",
"the resulting mesh is full of holes, mainly in the roofs which have",
"successfully subsampled it down to around 500,000 and I'm trying to print the",
"print it. Is there any algorithm which could use the fact that the",
"reconstruction. However, the resulting mesh is full of holes, mainly in the roofs",
"by laser scanning it with a Leica head. I successfully subsampled it down",
"down to around 500,000 and I'm trying to print the building by first",
"a very dense point cloud (billions of points) of the exterior of a",
"I cannot print it. Is there any algorithm which could use the fact",
"and PDAL, using Poisson surface reconstruction. However, the resulting mesh is full of",
"of holes, mainly in the roofs which have the lowest point density, and",
"roofs which have the lowest point density, and I cannot print it. Is",
"which have the lowest point density, and I cannot print it. Is there",
"first creating a mesh. I tried using CloudCompare, Meshlab and PDAL, using Poisson",
"obtained by laser scanning it with a Leica head. I successfully subsampled it",
"is full of holes, mainly in the roofs which have the lowest point",
"points) of the exterior of a building obtained by laser scanning it with",
"cannot print it. Is there any algorithm which could use the fact that",
"resulting mesh is full of holes, mainly in the roofs which have the",
"I tried using CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction. However, the",
"algorithm which could use the fact that the point cloud is precisely the",
"a Leica head. I successfully subsampled it down to around 500,000 and I'm",
"by first creating a mesh. I tried using CloudCompare, Meshlab and PDAL, using",
"However, the resulting mesh is full of holes, mainly in the roofs which",
"subsampled it down to around 500,000 and I'm trying to print the building",
"Poisson surface reconstruction. However, the resulting mesh is full of holes, mainly in",
"which could use the fact that the point cloud is precisely the exterior",
"a mesh. I tried using CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction.",
"it down to around 500,000 and I'm trying to print the building by",
"dense point cloud (billions of points) of the exterior of a building obtained",
"around 500,000 and I'm trying to print the building by first creating a",
"I'm trying to print the building by first creating a mesh. I tried",
"it. Is there any algorithm which could use the fact that the point",
"the lowest point density, and I cannot print it. Is there any algorithm",
"with a Leica head. I successfully subsampled it down to around 500,000 and",
"the roofs which have the lowest point density, and I cannot print it.",
"in the roofs which have the lowest point density, and I cannot print",
"holes, mainly in the roofs which have the lowest point density, and I",
"500,000 and I'm trying to print the building by first creating a mesh.",
"scanning it with a Leica head. I successfully subsampled it down to around",
"tried using CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction. However, the resulting",
"CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction. However, the resulting mesh is",
"mesh is full of holes, mainly in the roofs which have the lowest",
"very dense point cloud (billions of points) of the exterior of a building",
"have a very dense point cloud (billions of points) of the exterior of",
"Is there any algorithm which could use the fact that the point cloud",
"I successfully subsampled it down to around 500,000 and I'm trying to print",
"fact that the point cloud is precisely the exterior part of a geometric",
"surface reconstruction. However, the resulting mesh is full of holes, mainly in the",
"the building by first creating a mesh. I tried using CloudCompare, Meshlab and",
"and I'm trying to print the building by first creating a mesh. I",
"print the building by first creating a mesh. I tried using CloudCompare, Meshlab",
"use the fact that the point cloud is precisely the exterior part of",
"of a building obtained by laser scanning it with a Leica head. I",
"mesh. I tried using CloudCompare, Meshlab and PDAL, using Poisson surface reconstruction. However,",
"lowest point density, and I cannot print it. Is there any algorithm which",
"there any algorithm which could use the fact that the point cloud is",
"to around 500,000 and I'm trying to print the building by first creating",
"and I cannot print it. Is there any algorithm which could use the",
"point density, and I cannot print it. Is there any algorithm which could",
"laser scanning it with a Leica head. I successfully subsampled it down to",
"it with a Leica head. I successfully subsampled it down to around 500,000"
] |
[
"was working on a model today and I need to make the black",
"to select the black surface. I tried using the flip normals feature, but",
"today and I need to make the black surface into a normal surface",
"normals feature, but I was still unable to select it. Any advice on",
"a solid is greatly appreciated. Thanks. :) Edit: Here's the link to the",
"solid is greatly appreciated. Thanks. :) Edit: Here's the link to the file",
"the black surface into a normal surface so that the ship's cockpit is",
"feature, but I was still unable to select it. Any advice on how",
"Any advice on how to make it into a solid is greatly appreciated.",
"into a normal surface so that the ship's cockpit is solid. I am",
"surface so that the ship's cockpit is solid. I am unable to select",
"the black surface. I tried using the flip normals feature, but I was",
"to make it into a solid is greatly appreciated. Thanks. :) Edit: Here's",
"so that the ship's cockpit is solid. I am unable to select the",
"cockpit is solid. I am unable to select the black surface. I tried",
"I need to make the black surface into a normal surface so that",
"greatly appreciated. Thanks. :) Edit: Here's the link to the file <https://drive.google.com/file/d/1mbTdeeZqhNJx-WlXNqF8mD8QYDSI3Vh_/view?usp=sharing> [](https://i.stack.imgur.com/bInCO.png)",
"but I was still unable to select it. Any advice on how to",
"is solid. I am unable to select the black surface. I tried using"
] |
[
"of product I could coat the pieces, non-toxicity is a requirement because it",
"my irrigation system, like tube connectors and such. I am aware that PLA",
"printing some pieces for my irrigation system, like tube connectors and such. I",
"aware that PLA is hydrophilic so I was wondering with what kind of",
"So, what kind of non-toxic product can I use to coat PLA to",
"I am aware that PLA is hydrophilic so I was wondering with what",
"system, like tube connectors and such. I am aware that PLA is hydrophilic",
"for my irrigation system, like tube connectors and such. I am aware that",
"I could coat the pieces, non-toxicity is a requirement because it will water",
"that PLA is hydrophilic so I was wondering with what kind of product",
"pieces, non-toxicity is a requirement because it will water edible greens. So, what",
"with what kind of product I could coat the pieces, non-toxicity is a",
"non-toxicity is a requirement because it will water edible greens. So, what kind",
"hydrophilic so I was wondering with what kind of product I could coat",
"a requirement because it will water edible greens. So, what kind of non-toxic",
"because it will water edible greens. So, what kind of non-toxic product can",
"like tube connectors and such. I am aware that PLA is hydrophilic so",
"will water edible greens. So, what kind of non-toxic product can I use",
"of non-toxic product can I use to coat PLA to make it hydrophobic?",
"I was considering printing some pieces for my irrigation system, like tube connectors",
"such. I am aware that PLA is hydrophilic so I was wondering with",
"it will water edible greens. So, what kind of non-toxic product can I",
"pieces for my irrigation system, like tube connectors and such. I am aware",
"what kind of non-toxic product can I use to coat PLA to make",
"what kind of product I could coat the pieces, non-toxicity is a requirement",
"the pieces, non-toxicity is a requirement because it will water edible greens. So,",
"is a requirement because it will water edible greens. So, what kind of",
"requirement because it will water edible greens. So, what kind of non-toxic product",
"so I was wondering with what kind of product I could coat the",
"product I could coat the pieces, non-toxicity is a requirement because it will",
"coat the pieces, non-toxicity is a requirement because it will water edible greens.",
"greens. So, what kind of non-toxic product can I use to coat PLA",
"connectors and such. I am aware that PLA is hydrophilic so I was",
"water edible greens. So, what kind of non-toxic product can I use to",
"I was wondering with what kind of product I could coat the pieces,",
"wondering with what kind of product I could coat the pieces, non-toxicity is",
"kind of product I could coat the pieces, non-toxicity is a requirement because",
"kind of non-toxic product can I use to coat PLA to make it",
"considering printing some pieces for my irrigation system, like tube connectors and such.",
"was considering printing some pieces for my irrigation system, like tube connectors and",
"tube connectors and such. I am aware that PLA is hydrophilic so I",
"was wondering with what kind of product I could coat the pieces, non-toxicity",
"edible greens. So, what kind of non-toxic product can I use to coat",
"is hydrophilic so I was wondering with what kind of product I could",
"am aware that PLA is hydrophilic so I was wondering with what kind",
"could coat the pieces, non-toxicity is a requirement because it will water edible",
"some pieces for my irrigation system, like tube connectors and such. I am",
"irrigation system, like tube connectors and such. I am aware that PLA is",
"PLA is hydrophilic so I was wondering with what kind of product I",
"and such. I am aware that PLA is hydrophilic so I was wondering"
] |
[
"Given a large set of data, I was able to create a 3D",
"this graph to create a physical model of this graph? [](https://i.stack.imgur.com/xvJhX.jpg)",
"I was able to create a 3D graph in Microsoft Excel. How can",
"3D graph in Microsoft Excel. How can I create a STL file similar",
"file similar to this graph to create a physical model of this graph?",
"similar to this graph to create a physical model of this graph? [![enter",
"able to create a 3D graph in Microsoft Excel. How can I create",
"create a STL file similar to this graph to create a physical model",
"Excel. How can I create a STL file similar to this graph to",
"of data, I was able to create a 3D graph in Microsoft Excel.",
"set of data, I was able to create a 3D graph in Microsoft",
"graph in Microsoft Excel. How can I create a STL file similar to",
"I create a STL file similar to this graph to create a physical",
"can I create a STL file similar to this graph to create a",
"STL file similar to this graph to create a physical model of this",
"How can I create a STL file similar to this graph to create",
"to create a 3D graph in Microsoft Excel. How can I create a",
"large set of data, I was able to create a 3D graph in",
"a large set of data, I was able to create a 3D graph",
"a STL file similar to this graph to create a physical model of",
"a 3D graph in Microsoft Excel. How can I create a STL file"
] |
[
"to estimate how long it will take to print on a given printer?",
"is there a good way to estimate how long it will take to",
"print on a given printer? I know there are a lot of things",
"will take to print on a given printer? I know there are a",
"are a lot of things that go into print speed, such as the",
"application that you could enter your printer's specifications and the stl that you",
"a lot of things that go into print speed, such as the speed",
"good way to estimate how long it will take to print on a",
"as the speed of the printer, the size of the print, etc. I",
"on a given printer? I know there are a lot of things that",
"have a stl file is there a good way to estimate how long",
"I have a stl file is there a good way to estimate how",
"estimate how long it will take to print on a given printer? I",
"to print on a given printer? I know there are a lot of",
"I was wondering if anyone knows of perhaps an application that you could",
"take to print on a given printer? I know there are a lot",
"into print speed, such as the speed of the printer, the size of",
"if anyone knows of perhaps an application that you could enter your printer's",
"speed, such as the speed of the printer, the size of the print,",
"such as the speed of the printer, the size of the print, etc.",
"print, etc. I was wondering if anyone knows of perhaps an application that",
"etc. I was wondering if anyone knows of perhaps an application that you",
"printer, the size of the print, etc. I was wondering if anyone knows",
"file is there a good way to estimate how long it will take",
"the speed of the printer, the size of the print, etc. I was",
"speed of the printer, the size of the print, etc. I was wondering",
"anyone knows of perhaps an application that you could enter your printer's specifications",
"know there are a lot of things that go into print speed, such",
"and the stl that you want to print, and it could calculate the",
"printer? I know there are a lot of things that go into print",
"a given printer? I know there are a lot of things that go",
"was wondering if anyone knows of perhaps an application that you could enter",
"that you could enter your printer's specifications and the stl that you want",
"lot of things that go into print speed, such as the speed of",
"a good way to estimate how long it will take to print on",
"an application that you could enter your printer's specifications and the stl that",
"perhaps an application that you could enter your printer's specifications and the stl",
"you could enter your printer's specifications and the stl that you want to",
"long it will take to print on a given printer? I know there",
"the printer, the size of the print, etc. I was wondering if anyone",
"could enter your printer's specifications and the stl that you want to print,",
"I know there are a lot of things that go into print speed,",
"size of the print, etc. I was wondering if anyone knows of perhaps",
"stl file is there a good way to estimate how long it will",
"wondering if anyone knows of perhaps an application that you could enter your",
"printer's specifications and the stl that you want to print, and it could",
"of the print, etc. I was wondering if anyone knows of perhaps an",
"how long it will take to print on a given printer? I know",
"enter your printer's specifications and the stl that you want to print, and",
"given printer? I know there are a lot of things that go into",
"of perhaps an application that you could enter your printer's specifications and the",
"the size of the print, etc. I was wondering if anyone knows of",
"there are a lot of things that go into print speed, such as",
"the print, etc. I was wondering if anyone knows of perhaps an application",
"knows of perhaps an application that you could enter your printer's specifications and",
"the stl that you want to print, and it could calculate the print",
"of things that go into print speed, such as the speed of the",
"specifications and the stl that you want to print, and it could calculate",
"it will take to print on a given printer? I know there are",
"If I have a stl file is there a good way to estimate",
"of the printer, the size of the print, etc. I was wondering if",
"stl that you want to print, and it could calculate the print time?",
"print speed, such as the speed of the printer, the size of the",
"go into print speed, such as the speed of the printer, the size",
"way to estimate how long it will take to print on a given",
"things that go into print speed, such as the speed of the printer,",
"there a good way to estimate how long it will take to print",
"a stl file is there a good way to estimate how long it",
"your printer's specifications and the stl that you want to print, and it",
"that go into print speed, such as the speed of the printer, the"
] |
[
"mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even",
"I tightened everything as before. I am quite sure it doesn't have to",
"[extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really bad, even though I tightened",
"A8 after it was fully used up. When I started printing with my",
"use tape with PVA glue. Any advice on how to remove this under",
"I am quite sure it doesn't have to do with adhesion to the",
"have to do with adhesion to the heated bed since I use tape",
"up. When I started printing with my new 0.4 mm nozzle (same as",
"* 200 °C nozzle * 60 °C bed * PLA filament; * 0.4",
"changed my nozzle on my Anet A8 after it was fully used up.",
"the heated bed since I use tape with PVA glue. Any advice on",
"doesn't have to do with adhesion to the heated bed since I use",
"PVA glue. Any advice on how to remove this under extrusion so I",
"layer off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch,",
"the nozzle switch, it is really bad, even though I tightened everything as",
"and inconsistent, even so bad I couldn't continue printing because it would pull",
"started printing with my new 0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg)",
"first layer print speed * 200 °C nozzle * 60 °C bed *",
"on my Anet A8 after it was fully used up. When I started",
"really bad, even though I tightened everything as before. I am quite sure",
"Anet A8 after it was fully used up. When I started printing with",
"specs: * 25 mm/s first layer print speed * 200 °C nozzle *",
"printing with my new 0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was",
"If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is",
"size Let me know if there is anything else you need to know.",
"even though I tightened everything as before. I am quite sure it doesn't",
"as before. I am quite sure it doesn't have to do with adhesion",
"with adhesion to the heated bed since I use tape with PVA glue.",
"with PVA glue. Any advice on how to remove this under extrusion so",
"nozzle * 60 °C bed * PLA filament; * 0.4 mm nozzle size",
"my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really bad, even though I",
"am quite sure it doesn't have to do with adhesion to the heated",
"remove this under extrusion so I can continue printing? All the specs: *",
"on how to remove this under extrusion so I can continue printing? All",
"* 25 mm/s first layer print speed * 200 °C nozzle * 60",
"because it would pull the first layer off. If I compare it to",
"since I use tape with PVA glue. Any advice on how to remove",
"do with adhesion to the heated bed since I use tape with PVA",
"bad, even though I tightened everything as before. I am quite sure it",
"off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it",
"so I can continue printing? All the specs: * 25 mm/s first layer",
"was VERY bad and inconsistent, even so bad I couldn't continue printing because",
"speed * 200 °C nozzle * 60 °C bed * PLA filament; *",
"this under extrusion so I can continue printing? All the specs: * 25",
"0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent,",
"to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really bad, even though",
"printing? All the specs: * 25 mm/s first layer print speed * 200",
"it doesn't have to do with adhesion to the heated bed since I",
"everything as before. I am quite sure it doesn't have to do with",
"fully used up. When I started printing with my new 0.4 mm nozzle",
"extrusion so I can continue printing? All the specs: * 25 mm/s first",
"just changed my nozzle on my Anet A8 after it was fully used",
"before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so bad I couldn't",
"[extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so bad I couldn't continue printing",
"can continue printing? All the specs: * 25 mm/s first layer print speed",
"to remove this under extrusion so I can continue printing? All the specs:",
"sure it doesn't have to do with adhesion to the heated bed since",
"nozzle switch, it is really bad, even though I tightened everything as before.",
"60 °C bed * PLA filament; * 0.4 mm nozzle size Let me",
"quite sure it doesn't have to do with adhesion to the heated bed",
"would pull the first layer off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg)",
"mm/s first layer print speed * 200 °C nozzle * 60 °C bed",
"my new 0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad",
"first layer off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle",
"When I started printing with my new 0.4 mm nozzle (same as before)",
"°C nozzle * 60 °C bed * PLA filament; * 0.4 mm nozzle",
"couldn't continue printing because it would pull the first layer off. If I",
"bed * PLA filament; * 0.4 mm nozzle size Let me know if",
"though I tightened everything as before. I am quite sure it doesn't have",
"nozzle on my Anet A8 after it was fully used up. When I",
"continue printing because it would pull the first layer off. If I compare",
"how to remove this under extrusion so I can continue printing? All the",
"switch, it is really bad, even though I tightened everything as before. I",
"it is really bad, even though I tightened everything as before. I am",
"filament; * 0.4 mm nozzle size Let me know if there is anything",
"pull the first layer off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before",
"before the nozzle switch, it is really bad, even though I tightened everything",
"(same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so bad",
"I use tape with PVA glue. Any advice on how to remove this",
"after it was fully used up. When I started printing with my new",
"it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really bad, even",
"* 0.4 mm nozzle size Let me know if there is anything else",
"I just changed my nozzle on my Anet A8 after it was fully",
"°C bed * PLA filament; * 0.4 mm nozzle size Let me know",
"with my new 0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY",
"printing because it would pull the first layer off. If I compare it",
"25 mm/s first layer print speed * 200 °C nozzle * 60 °C",
"used up. When I started printing with my new 0.4 mm nozzle (same",
"I started printing with my new 0.4 mm nozzle (same as before) my",
"All the specs: * 25 mm/s first layer print speed * 200 °C",
"tape with PVA glue. Any advice on how to remove this under extrusion",
"bad and inconsistent, even so bad I couldn't continue printing because it would",
"* PLA filament; * 0.4 mm nozzle size Let me know if there",
"VERY bad and inconsistent, even so bad I couldn't continue printing because it",
"it was fully used up. When I started printing with my new 0.4",
"was fully used up. When I started printing with my new 0.4 mm",
"I couldn't continue printing because it would pull the first layer off. If",
"Any advice on how to remove this under extrusion so I can continue",
"* 60 °C bed * PLA filament; * 0.4 mm nozzle size Let",
"bed since I use tape with PVA glue. Any advice on how to",
"new 0.4 mm nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and",
"before. I am quite sure it doesn't have to do with adhesion to",
"nozzle (same as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so",
"even so bad I couldn't continue printing because it would pull the first",
"my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so bad I couldn't continue",
"my Anet A8 after it was fully used up. When I started printing",
"inconsistent, even so bad I couldn't continue printing because it would pull the",
"as before) my [extrusion](https://i.stack.imgur.com/KEOul.jpg) was VERY bad and inconsistent, even so bad I",
"tightened everything as before. I am quite sure it doesn't have to do",
"adhesion to the heated bed since I use tape with PVA glue. Any",
"glue. Any advice on how to remove this under extrusion so I can",
"layer print speed * 200 °C nozzle * 60 °C bed * PLA",
"so bad I couldn't continue printing because it would pull the first layer",
"200 °C nozzle * 60 °C bed * PLA filament; * 0.4 mm",
"compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really bad,",
"mm nozzle size Let me know if there is anything else you need",
"to do with adhesion to the heated bed since I use tape with",
"to the heated bed since I use tape with PVA glue. Any advice",
"nozzle size Let me know if there is anything else you need to",
"0.4 mm nozzle size Let me know if there is anything else you",
"advice on how to remove this under extrusion so I can continue printing?",
"the specs: * 25 mm/s first layer print speed * 200 °C nozzle",
"it would pull the first layer off. If I compare it to my",
"is really bad, even though I tightened everything as before. I am quite",
"under extrusion so I can continue printing? All the specs: * 25 mm/s",
"PLA filament; * 0.4 mm nozzle size Let me know if there is",
"I can continue printing? All the specs: * 25 mm/s first layer print",
"print speed * 200 °C nozzle * 60 °C bed * PLA filament;",
"continue printing? All the specs: * 25 mm/s first layer print speed *",
"the first layer off. If I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the",
"I compare it to my [extrusion](https://i.stack.imgur.com/5cjuO.jpg) before the nozzle switch, it is really",
"my nozzle on my Anet A8 after it was fully used up. When",
"heated bed since I use tape with PVA glue. Any advice on how",
"bad I couldn't continue printing because it would pull the first layer off."
] |
[
"use a 12 Volts, 16 amperes power supply, but I understand that you",
"extruder need 5 amp, and the heated bed build plate needs 11 amp.",
"of delivering 25 amp and 30 amp and they told me that if",
"and 30 amp and they told me that if I use those ones",
"20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors",
"30 amp and they told me that if I use those ones you",
"rated for 25% more than you need In the place where I buy",
"the heated bed. Is that true? I understand that the heated bed is",
"In the place where I buy the spare parts for my 3d printer",
"the heating of the heated bed. Is that true? I understand that the",
"description here](https://i.stack.imgur.com/fXymv.jpg)](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a 12 Volts, 16 amperes",
"supply, but I understand that you use the one with 20 amp because",
"currents from extruders and stepper motors can be stressful to supplies loaded to",
"from extruders and stepper motors can be stressful to supplies loaded to the",
"a supply rated for 25% more than you need In the place where",
"for my 3d printer they also sell 12 V power supplies capable of",
"image description here](https://i.stack.imgur.com/fXymv.jpg)](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a 12 Volts, 16",
"bed build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only",
"Technically you only need to use a 12 Volts, 16 amperes power supply,",
"I buy the spare parts for my 3d printer they also sell 12",
"supplies loaded to the max, so for reliability and performance, it is better",
"to speed up the heating of the heated bed. Is that true? I",
"image description here](https://i.stack.imgur.com/fraEVm.jpg)](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need 5 amp, and",
"going to make any difference to use power supplies capable of delivering more",
"volts, 20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper",
"loaded to the max, so for reliability and performance, it is better to",
"sell 12 V power supplies capable of delivering 25 amp and 30 amp",
"I use those ones you are going to be able to speed up",
"with 20 amp because pulse currents from extruders and stepper motors can be",
"and the extruder need 5 amp, and the heated bed build plate needs",
"is only going to take the 11 amp that it needs so is",
"you only need to use a 12 Volts, 16 amperes power supply, but",
"performance, it is better to use a supply rated for 25% more than",
"heated bed is only going to take the 11 amp that it needs",
"power supply, but I understand that you use the one with 20 amp",
"a 12 Volts, 16 amperes power supply, but I understand that you use",
"be stressful to supplies loaded to the max, so for reliability and performance,",
"motors can be stressful to supplies loaded to the max, so for reliability",
"max, so for reliability and performance, it is better to use a supply",
"power supplies capable of delivering 25 amp and 30 amp and they told",
"a 12 volts, 20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg)",
"ones you are going to be able to speed up the heating of",
"(Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need",
"you are going to be able to speed up the heating of the",
"buy the spare parts for my 3d printer they also sell 12 V",
"25 amp and 30 amp and they told me that if I use",
"than you need In the place where I buy the spare parts for",
"you use the one with 20 amp because pulse currents from extruders and",
"my 3d printer they also sell 12 V power supplies capable of delivering",
"need In the place where I buy the spare parts for my 3d",
"supply rated for 25% more than you need In the place where I",
"to make any difference to use power supplies capable of delivering more current",
"able to speed up the heating of the heated bed. Is that true?",
"that true? I understand that the heated bed is only going to take",
"to be able to speed up the heating of the heated bed. Is",
"of the heated bed. Is that true? I understand that the heated bed",
"not going to make any difference to use power supplies capable of delivering",
"use the one with 20 amp because pulse currents from extruders and stepper",
"motors and the extruder need 5 amp, and the heated bed build plate",
"if I use those ones you are going to be able to speed",
"and the heated bed build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg)",
"understand that you use the one with 20 amp because pulse currents from",
"also sell 12 V power supplies capable of delivering 25 amp and 30",
"stepper motors and the extruder need 5 amp, and the heated bed build",
"that if I use those ones you are going to be able to",
"11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a",
"using a 12 volts, 20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a 12 Volts,",
"use a supply rated for 25% more than you need In the place",
"Currently I am using a 12 volts, 20 amperes power supply (Model S-240-12)",
"and performance, it is better to use a supply rated for 25% more",
"because pulse currents from extruders and stepper motors can be stressful to supplies",
"stepper motors can be stressful to supplies loaded to the max, so for",
"pulse currents from extruders and stepper motors can be stressful to supplies loaded",
"to use a supply rated for 25% more than you need In the",
"S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need 5",
"description here](https://i.stack.imgur.com/fraEVm.jpg)](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need 5 amp, and the",
"so is not going to make any difference to use power supplies capable",
"are going to be able to speed up the heating of the heated",
"use those ones you are going to be able to speed up the",
"amp, and the heated bed build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically",
"but I understand that you use the one with 20 amp because pulse",
"25% more than you need In the place where I buy the spare",
"here](https://i.stack.imgur.com/fraEVm.jpg)](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need 5 amp, and the heated",
"you need In the place where I buy the spare parts for my",
"plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to",
"heating of the heated bed. Is that true? I understand that the heated",
"so for reliability and performance, it is better to use a supply rated",
"understand that the heated bed is only going to take the 11 amp",
"I am using a 12 volts, 20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder need 5 amp,",
"up the heating of the heated bed. Is that true? I understand that",
"the heated bed is only going to take the 11 amp that it",
"20 amp because pulse currents from extruders and stepper motors can be stressful",
"bed. Is that true? I understand that the heated bed is only going",
"Is that true? I understand that the heated bed is only going to",
"5 amp, and the heated bed build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you",
"amperes power supply, but I understand that you use the one with 20",
"amp because pulse currents from extruders and stepper motors can be stressful to",
"that you use the one with 20 amp because pulse currents from extruders",
"to the max, so for reliability and performance, it is better to use",
"only need to use a 12 Volts, 16 amperes power supply, but I",
"printer they also sell 12 V power supplies capable of delivering 25 amp",
"place where I buy the spare parts for my 3d printer they also",
"stressful to supplies loaded to the max, so for reliability and performance, it",
"reliability and performance, it is better to use a supply rated for 25%",
"amp and 30 amp and they told me that if I use those",
"better to use a supply rated for 25% more than you need In",
"Volts, 16 amperes power supply, but I understand that you use the one",
"amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a 12",
"one with 20 amp because pulse currents from extruders and stepper motors can",
"spare parts for my 3d printer they also sell 12 V power supplies",
"delivering 25 amp and 30 amp and they told me that if I",
"the one with 20 amp because pulse currents from extruders and stepper motors",
"heated bed. Is that true? I understand that the heated bed is only",
"is better to use a supply rated for 25% more than you need",
"those ones you are going to be able to speed up the heating",
"be able to speed up the heating of the heated bed. Is that",
"the max, so for reliability and performance, it is better to use a",
"capable of delivering 25 amp and 30 amp and they told me that",
"true? I understand that the heated bed is only going to take the",
"the place where I buy the spare parts for my 3d printer they",
"3d printer they also sell 12 V power supplies capable of delivering 25",
"only going to take the 11 amp that it needs so is not",
"needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use",
"amp and they told me that if I use those ones you are",
"it needs so is not going to make any difference to use power",
"amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and",
"The stepper motors and the extruder need 5 amp, and the heated bed",
"11 amp that it needs so is not going to make any difference",
"to use a 12 Volts, 16 amperes power supply, but I understand that",
"extruders and stepper motors can be stressful to supplies loaded to the max,",
"parts for my 3d printer they also sell 12 V power supplies capable",
"that it needs so is not going to make any difference to use",
"is not going to make any difference to use power supplies capable of",
"V power supplies capable of delivering 25 amp and 30 amp and they",
"build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need",
"told me that if I use those ones you are going to be",
"me that if I use those ones you are going to be able",
"need 5 amp, and the heated bed build plate needs 11 amp. [](https://i.stack.imgur.com/fXymv.jpg) Technically you only need to use a 12 Volts, 16 amperes power",
"they also sell 12 V power supplies capable of delivering 25 amp and",
"12 V power supplies capable of delivering 25 amp and 30 amp and",
"power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the",
"supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The stepper motors and the extruder",
"where I buy the spare parts for my 3d printer they also sell",
"12 volts, 20 amperes power supply (Model S-240-12) [](https://i.stack.imgur.com/fraEVm.jpg) The",
"speed up the heating of the heated bed. Is that true? I understand",
"need to use a 12 Volts, 16 amperes power supply, but I understand",
"am using a 12 volts, 20 amperes power supply (Model S-240-12) [![enter image",
"to supplies loaded to the max, so for reliability and performance, it is",
"supplies capable of delivering 25 amp and 30 amp and they told me"
] |
[
"working. What I did: 1. I check whether or not motor is moving",
"out cable and plugs - everything seems OK. 3. I checked whether motor",
"I'm sure one day someone will have same problem. I own a ZONESTAR",
"can I do, to see what is broken? Visually nothing looks like it",
"my trembling hands. After some googling, I started checking A4988 stepper driver with",
"so it seems to work at least in this way. What can I",
"least in this way. What can I do, to see what is broken?",
"seemed to get lower, but I'm almost sure it is my trembling hands.",
"manually. 2. I checked out cable and plugs - everything seems OK. 3.",
"trembling hands. After some googling, I started checking A4988 stepper driver with my",
"would seem that there is something wrong with E0-mot driver module, or with",
"almost sure it is my trembling hands. After some googling, I started checking",
"not. It would seem that there is something wrong with E0-mot driver module,",
"after plugging it into same slot on mainboard - and it does not.",
"was ~5V and VMOT around 12V, so it seems to work at least",
"freely - I can rotate it without any problems manually. 2. I checked",
"VDD was ~5V and VMOT around 12V, so it seems to work at",
"12V, so it seems to work at least in this way. What can",
"it seems to work at least in this way. What can I do,",
"between red and black, I guess V+ and ground). It sometimes seemed to",
"my extruder motor stopped working. What I did: 1. I check whether or",
"does not. It would seem that there is something wrong with E0-mot driver",
"motor seems fine(11.3V between red and black, I guess V+ and ground). It",
"checked if another motor works after plugging it into same slot on mainboard",
"about what can I do with any of those. I do not have",
"is broken? Visually nothing looks like it burned out, but I'm fully aware",
"whether motor is working after plugging it into another slot in motherboard -",
"if another motor works after plugging it into same slot on mainboard -",
"my multimeter. VDD was ~5V and VMOT around 12V, so it seems to",
"I checked out cable and plugs - everything seems OK. 3. I checked",
"with any of those. I do not have any electronic equipment except multimeter,",
"will have same problem. I own a ZONESTAR P802QSU (Bowden extruder) and all",
"check whether or not motor is moving freely - I can rotate it",
"While this may seem like terribly noobish question, I'm sure one day someone",
"after plugging it into another slot in motherboard - motor works fine. 4.",
"works after plugging it into same slot on mainboard - and it does",
"on mainboard - and it does not. It would seem that there is",
"seem that there is something wrong with E0-mot driver module, or with socket.",
"but I'm almost sure it is my trembling hands. After some googling, I",
"I do, to see what is broken? Visually nothing looks like it burned",
"any problems manually. 2. I checked out cable and plugs - everything seems",
"plugs - everything seems OK. 3. I checked whether motor is working after",
"is working after plugging it into another slot in motherboard - motor works",
"same problem. I own a ZONESTAR P802QSU (Bowden extruder) and all of sudden",
"noobish question, I'm sure one day someone will have same problem. I own",
"into same slot on mainboard - and it does not. It would seem",
"slot in motherboard - motor works fine. 4. I checked if another motor",
"V+ and ground). It sometimes seemed to get lower, but I'm almost sure",
"another motor works after plugging it into same slot on mainboard - and",
"and it does not. It would seem that there is something wrong with",
"lower, but I'm almost sure it is my trembling hands. After some googling,",
"moving freely - I can rotate it without any problems manually. 2. I",
"googling, I started checking A4988 stepper driver with my multimeter. VDD was ~5V",
"it into another slot in motherboard - motor works fine. 4. I checked",
"or with socket. I'm however totally at loss about what can I do",
"and plugs - everything seems OK. 3. I checked whether motor is working",
"did: 1. I check whether or not motor is moving freely - I",
"have any electronic equipment except multimeter, and voltage on motor seems fine(11.3V between",
"and black, I guess V+ and ground). It sometimes seemed to get lower,",
"sure one day someone will have same problem. I own a ZONESTAR P802QSU",
"with socket. I'm however totally at loss about what can I do with",
"extruder) and all of sudden my extruder motor stopped working. What I did:",
"ZONESTAR P802QSU (Bowden extruder) and all of sudden my extruder motor stopped working.",
"it into same slot on mainboard - and it does not. It would",
"what can I do with any of those. I do not have any",
"day someone will have same problem. I own a ZONESTAR P802QSU (Bowden extruder)",
"P802QSU (Bowden extruder) and all of sudden my extruder motor stopped working. What",
"see what is broken? Visually nothing looks like it burned out, but I'm",
"- everything seems OK. 3. I checked whether motor is working after plugging",
"OK. 3. I checked whether motor is working after plugging it into another",
"on motor seems fine(11.3V between red and black, I guess V+ and ground).",
"can I do with any of those. I do not have any electronic",
"not have any electronic equipment except multimeter, and voltage on motor seems fine(11.3V",
"it is my trembling hands. After some googling, I started checking A4988 stepper",
"socket. I'm however totally at loss about what can I do with any",
"stepper driver with my multimeter. VDD was ~5V and VMOT around 12V, so",
"I can rotate it without any problems manually. 2. I checked out cable",
"plugging it into another slot in motherboard - motor works fine. 4. I",
"1. I check whether or not motor is moving freely - I can",
"seems fine(11.3V between red and black, I guess V+ and ground). It sometimes",
"guess V+ and ground). It sometimes seemed to get lower, but I'm almost",
"hands. After some googling, I started checking A4988 stepper driver with my multimeter.",
"to get lower, but I'm almost sure it is my trembling hands. After",
"motor works fine. 4. I checked if another motor works after plugging it",
"do with any of those. I do not have any electronic equipment except",
"ground). It sometimes seemed to get lower, but I'm almost sure it is",
"multimeter. VDD was ~5V and VMOT around 12V, so it seems to work",
"into another slot in motherboard - motor works fine. 4. I checked if",
"What can I do, to see what is broken? Visually nothing looks like",
"work at least in this way. What can I do, to see what",
"broken? Visually nothing looks like it burned out, but I'm fully aware it",
"terribly noobish question, I'm sure one day someone will have same problem. I",
"checked whether motor is working after plugging it into another slot in motherboard",
"totally at loss about what can I do with any of those. I",
"those. I do not have any electronic equipment except multimeter, and voltage on",
"After some googling, I started checking A4988 stepper driver with my multimeter. VDD",
"that there is something wrong with E0-mot driver module, or with socket. I'm",
"I guess V+ and ground). It sometimes seemed to get lower, but I'm",
"what is broken? Visually nothing looks like it burned out, but I'm fully",
"stopped working. What I did: 1. I check whether or not motor is",
"at loss about what can I do with any of those. I do",
"whether or not motor is moving freely - I can rotate it without",
"to see what is broken? Visually nothing looks like it burned out, but",
"and all of sudden my extruder motor stopped working. What I did: 1.",
"and VMOT around 12V, so it seems to work at least in this",
"driver module, or with socket. I'm however totally at loss about what can",
"without any problems manually. 2. I checked out cable and plugs - everything",
"with E0-mot driver module, or with socket. I'm however totally at loss about",
"is something wrong with E0-mot driver module, or with socket. I'm however totally",
"seems to work at least in this way. What can I do, to",
"way. What can I do, to see what is broken? Visually nothing looks",
"checked out cable and plugs - everything seems OK. 3. I checked whether",
"- and it does not. It would seem that there is something wrong",
"It would seem that there is something wrong with E0-mot driver module, or",
"VMOT around 12V, so it seems to work at least in this way.",
"another slot in motherboard - motor works fine. 4. I checked if another",
"A4988 stepper driver with my multimeter. VDD was ~5V and VMOT around 12V,",
"this may seem like terribly noobish question, I'm sure one day someone will",
"have same problem. I own a ZONESTAR P802QSU (Bowden extruder) and all of",
"plugging it into same slot on mainboard - and it does not. It",
"and voltage on motor seems fine(11.3V between red and black, I guess V+",
"Visually nothing looks like it burned out, but I'm fully aware it may",
"seems OK. 3. I checked whether motor is working after plugging it into",
"It sometimes seemed to get lower, but I'm almost sure it is my",
"~5V and VMOT around 12V, so it seems to work at least in",
"rotate it without any problems manually. 2. I checked out cable and plugs",
"(Bowden extruder) and all of sudden my extruder motor stopped working. What I",
"any electronic equipment except multimeter, and voltage on motor seems fine(11.3V between red",
"slot on mainboard - and it does not. It would seem that there",
"of sudden my extruder motor stopped working. What I did: 1. I check",
"problem. I own a ZONESTAR P802QSU (Bowden extruder) and all of sudden my",
"- motor works fine. 4. I checked if another motor works after plugging",
"of those. I do not have any electronic equipment except multimeter, and voltage",
"equipment except multimeter, and voltage on motor seems fine(11.3V between red and black,",
"voltage on motor seems fine(11.3V between red and black, I guess V+ and",
"around 12V, so it seems to work at least in this way. What",
"motor is working after plugging it into another slot in motherboard - motor",
"motor is moving freely - I can rotate it without any problems manually.",
"and ground). It sometimes seemed to get lower, but I'm almost sure it",
"get lower, but I'm almost sure it is my trembling hands. After some",
"like terribly noobish question, I'm sure one day someone will have same problem.",
"someone will have same problem. I own a ZONESTAR P802QSU (Bowden extruder) and",
"I do with any of those. I do not have any electronic equipment",
"fine(11.3V between red and black, I guess V+ and ground). It sometimes seemed",
"red and black, I guess V+ and ground). It sometimes seemed to get",
"I did: 1. I check whether or not motor is moving freely -",
"some googling, I started checking A4988 stepper driver with my multimeter. VDD was",
"cable and plugs - everything seems OK. 3. I checked whether motor is",
"checking A4988 stepper driver with my multimeter. VDD was ~5V and VMOT around",
"mainboard - and it does not. It would seem that there is something",
"one day someone will have same problem. I own a ZONESTAR P802QSU (Bowden",
"I'm however totally at loss about what can I do with any of",
"not motor is moving freely - I can rotate it without any problems",
"do, to see what is broken? Visually nothing looks like it burned out,",
"sometimes seemed to get lower, but I'm almost sure it is my trembling",
"there is something wrong with E0-mot driver module, or with socket. I'm however",
"fine. 4. I checked if another motor works after plugging it into same",
"this way. What can I do, to see what is broken? Visually nothing",
"in motherboard - motor works fine. 4. I checked if another motor works",
"like it burned out, but I'm fully aware it may not be visible.",
"multimeter, and voltage on motor seems fine(11.3V between red and black, I guess",
"a ZONESTAR P802QSU (Bowden extruder) and all of sudden my extruder motor stopped",
"working after plugging it into another slot in motherboard - motor works fine.",
"problems manually. 2. I checked out cable and plugs - everything seems OK.",
"or not motor is moving freely - I can rotate it without any",
"I checked if another motor works after plugging it into same slot on",
"own a ZONESTAR P802QSU (Bowden extruder) and all of sudden my extruder motor",
"something wrong with E0-mot driver module, or with socket. I'm however totally at",
"however totally at loss about what can I do with any of those.",
"with my multimeter. VDD was ~5V and VMOT around 12V, so it seems",
"- I can rotate it without any problems manually. 2. I checked out",
"module, or with socket. I'm however totally at loss about what can I",
"I checked whether motor is working after plugging it into another slot in",
"electronic equipment except multimeter, and voltage on motor seems fine(11.3V between red and",
"2. I checked out cable and plugs - everything seems OK. 3. I",
"motor works after plugging it into same slot on mainboard - and it",
"is moving freely - I can rotate it without any problems manually. 2.",
"all of sudden my extruder motor stopped working. What I did: 1. I",
"I'm almost sure it is my trembling hands. After some googling, I started",
"E0-mot driver module, or with socket. I'm however totally at loss about what",
"I started checking A4988 stepper driver with my multimeter. VDD was ~5V and",
"looks like it burned out, but I'm fully aware it may not be",
"3. I checked whether motor is working after plugging it into another slot",
"at least in this way. What can I do, to see what is",
"can rotate it without any problems manually. 2. I checked out cable and",
"motherboard - motor works fine. 4. I checked if another motor works after",
"may seem like terribly noobish question, I'm sure one day someone will have",
"to work at least in this way. What can I do, to see",
"question, I'm sure one day someone will have same problem. I own a",
"I check whether or not motor is moving freely - I can rotate",
"everything seems OK. 3. I checked whether motor is working after plugging it",
"motor stopped working. What I did: 1. I check whether or not motor",
"What I did: 1. I check whether or not motor is moving freely",
"started checking A4988 stepper driver with my multimeter. VDD was ~5V and VMOT",
"wrong with E0-mot driver module, or with socket. I'm however totally at loss",
"works fine. 4. I checked if another motor works after plugging it into",
"it without any problems manually. 2. I checked out cable and plugs -",
"except multimeter, and voltage on motor seems fine(11.3V between red and black, I",
"nothing looks like it burned out, but I'm fully aware it may not",
"4. I checked if another motor works after plugging it into same slot",
"it does not. It would seem that there is something wrong with E0-mot",
"loss about what can I do with any of those. I do not",
"seem like terribly noobish question, I'm sure one day someone will have same",
"driver with my multimeter. VDD was ~5V and VMOT around 12V, so it",
"sure it is my trembling hands. After some googling, I started checking A4988",
"do not have any electronic equipment except multimeter, and voltage on motor seems",
"I do not have any electronic equipment except multimeter, and voltage on motor",
"sudden my extruder motor stopped working. What I did: 1. I check whether",
"I own a ZONESTAR P802QSU (Bowden extruder) and all of sudden my extruder",
"same slot on mainboard - and it does not. It would seem that",
"any of those. I do not have any electronic equipment except multimeter, and",
"is my trembling hands. After some googling, I started checking A4988 stepper driver",
"black, I guess V+ and ground). It sometimes seemed to get lower, but",
"in this way. What can I do, to see what is broken? Visually",
"extruder motor stopped working. What I did: 1. I check whether or not"
] |
[
"regardless of the program I'm using (Repetier-Host or Cura 15). Is there a",
"of the program I'm using (Repetier-Host or Cura 15). Is there a way",
"and I need to heat it up to unjam it. Unfortunately, the printer",
"a micro SD card to heat up the printer hotend but not print",
"does't want to connect to my laptop regardless of the program I'm using",
"a way to use a micro SD card to heat up the printer",
"use a micro SD card to heat up the printer hotend but not",
"simple metal's extruder is jammed and I need to heat it up to",
"my laptop regardless of the program I'm using (Repetier-Host or Cura 15). Is",
"way to use a micro SD card to heat up the printer hotend",
"connect to my laptop regardless of the program I'm using (Repetier-Host or Cura",
"the printer does't want to connect to my laptop regardless of the program",
"Cura 15). Is there a way to use a micro SD card to",
"it up to unjam it. Unfortunately, the printer does't want to connect to",
"15). Is there a way to use a micro SD card to heat",
"to heat it up to unjam it. Unfortunately, the printer does't want to",
"program I'm using (Repetier-Host or Cura 15). Is there a way to use",
"micro SD card to heat up the printer hotend but not print anything?",
"metal's extruder is jammed and I need to heat it up to unjam",
"need to heat it up to unjam it. Unfortunately, the printer does't want",
"it. Unfortunately, the printer does't want to connect to my laptop regardless of",
"is jammed and I need to heat it up to unjam it. Unfortunately,",
"Unfortunately, the printer does't want to connect to my laptop regardless of the",
"laptop regardless of the program I'm using (Repetier-Host or Cura 15). Is there",
"unjam it. Unfortunately, the printer does't want to connect to my laptop regardless",
"jammed and I need to heat it up to unjam it. Unfortunately, the",
"there a way to use a micro SD card to heat up the",
"the program I'm using (Repetier-Host or Cura 15). Is there a way to",
"up to unjam it. Unfortunately, the printer does't want to connect to my",
"to connect to my laptop regardless of the program I'm using (Repetier-Host or",
"extruder is jammed and I need to heat it up to unjam it.",
"to use a micro SD card to heat up the printer hotend but",
"I need to heat it up to unjam it. Unfortunately, the printer does't",
"heat it up to unjam it. Unfortunately, the printer does't want to connect",
"I'm using (Repetier-Host or Cura 15). Is there a way to use a",
"Printrbot simple metal's extruder is jammed and I need to heat it up",
"printer does't want to connect to my laptop regardless of the program I'm",
"to unjam it. Unfortunately, the printer does't want to connect to my laptop",
"Is there a way to use a micro SD card to heat up",
"using (Repetier-Host or Cura 15). Is there a way to use a micro",
"(Repetier-Host or Cura 15). Is there a way to use a micro SD",
"to my laptop regardless of the program I'm using (Repetier-Host or Cura 15).",
"want to connect to my laptop regardless of the program I'm using (Repetier-Host",
"My Printrbot simple metal's extruder is jammed and I need to heat it",
"or Cura 15). Is there a way to use a micro SD card"
] |
[
"then need to 3D print these molds. I would require to add a",
"structure through which I could make the cylinder). Is there any way to",
"print these molds. I would require to add a hole to pour in",
"this object (i.e. the structure through which I could make the cylinder). Is",
"to do so? My requirement is as follows: I have an .stl file",
"design in .stl format. Suppose I have a 3D partin .stl format (for",
"and I want to make/design a mold for this object (i.e. the structure",
"Are there any tools to do so? My requirement is as follows: I",
"have a 3D partin .stl format (for e.g. a cylinder) and I want",
"an .stl file of a design and need to develop the CAD files",
"I have a 3D partin .stl format (for e.g. a cylinder) and I",
"there any way to do so? Are there any tools to do so?",
"make the cylinder). Is there any way to do so? Are there any",
"of a design and need to develop the CAD files for its mold.",
"know how to make a mold of a 3D design in .stl format.",
"for its mold. I will then need to 3D print these molds. I",
"and need to develop the CAD files for its mold. I will then",
"a cylinder) and I want to make/design a mold for this object (i.e.",
"so? Are there any tools to do so? My requirement is as follows:",
"3D partin .stl format (for e.g. a cylinder) and I want to make/design",
"as follows: I have an .stl file of a design and need to",
"the cylinder). Is there any way to do so? Are there any tools",
"have an .stl file of a design and need to develop the CAD",
"to make/design a mold for this object (i.e. the structure through which I",
"to make a mold of a 3D design in .stl format. Suppose I",
"object (i.e. the structure through which I could make the cylinder). Is there",
"(for e.g. a cylinder) and I want to make/design a mold for this",
"want to know how to make a mold of a 3D design in",
"a mold for this object (i.e. the structure through which I could make",
"need to develop the CAD files for its mold. I will then need",
"format. Suppose I have a 3D partin .stl format (for e.g. a cylinder)",
"the structure through which I could make the cylinder). Is there any way",
"which I could make the cylinder). Is there any way to do so?",
"could make the cylinder). Is there any way to do so? Are there",
"mold of a 3D design in .stl format. Suppose I have a 3D",
"3D print these molds. I would require to add a hole to pour",
"to add a hole to pour in liquid (resin based) raw material which",
"My requirement is as follows: I have an .stl file of a design",
"cylinder). Is there any way to do so? Are there any tools to",
"want to make/design a mold for this object (i.e. the structure through which",
"make/design a mold for this object (i.e. the structure through which I could",
"make a mold of a 3D design in .stl format. Suppose I have",
"to 3D print these molds. I would require to add a hole to",
"in .stl format. Suppose I have a 3D partin .stl format (for e.g.",
"to know how to make a mold of a 3D design in .stl",
"do so? Are there any tools to do so? My requirement is as",
"these molds. I would require to add a hole to pour in liquid",
"I would require to add a hole to pour in liquid (resin based)",
"a design and need to develop the CAD files for its mold. I",
"I want to know how to make a mold of a 3D design",
".stl file of a design and need to develop the CAD files for",
"need to 3D print these molds. I would require to add a hole",
"would require to add a hole to pour in liquid (resin based) raw",
"follows: I have an .stl file of a design and need to develop",
"any tools to do so? My requirement is as follows: I have an",
"tools to do so? My requirement is as follows: I have an .stl",
"there any tools to do so? My requirement is as follows: I have",
"Is there any way to do so? Are there any tools to do",
"a 3D design in .stl format. Suppose I have a 3D partin .stl",
"so? My requirement is as follows: I have an .stl file of a",
"mold. I will then need to 3D print these molds. I would require",
"add a hole to pour in liquid (resin based) raw material which hardens",
"I want to make/design a mold for this object (i.e. the structure through",
"a hole to pour in liquid (resin based) raw material which hardens with",
"a 3D partin .stl format (for e.g. a cylinder) and I want to",
"CAD files for its mold. I will then need to 3D print these",
"for this object (i.e. the structure through which I could make the cylinder).",
"partin .stl format (for e.g. a cylinder) and I want to make/design a",
"format (for e.g. a cylinder) and I want to make/design a mold for",
"to develop the CAD files for its mold. I will then need to",
"do so? My requirement is as follows: I have an .stl file of",
"e.g. a cylinder) and I want to make/design a mold for this object",
"any way to do so? Are there any tools to do so? My",
".stl format (for e.g. a cylinder) and I want to make/design a mold",
"require to add a hole to pour in liquid (resin based) raw material",
"(i.e. the structure through which I could make the cylinder). Is there any",
"Suppose I have a 3D partin .stl format (for e.g. a cylinder) and",
"3D design in .stl format. Suppose I have a 3D partin .stl format",
"is as follows: I have an .stl file of a design and need",
"how to make a mold of a 3D design in .stl format. Suppose",
"a mold of a 3D design in .stl format. Suppose I have a",
"hole to pour in liquid (resin based) raw material which hardens with time.",
"I have an .stl file of a design and need to develop the",
"of a 3D design in .stl format. Suppose I have a 3D partin",
"mold for this object (i.e. the structure through which I could make the",
"way to do so? Are there any tools to do so? My requirement",
"files for its mold. I will then need to 3D print these molds.",
"to do so? Are there any tools to do so? My requirement is",
"file of a design and need to develop the CAD files for its",
"I could make the cylinder). Is there any way to do so? Are",
"the CAD files for its mold. I will then need to 3D print",
"through which I could make the cylinder). Is there any way to do",
".stl format. Suppose I have a 3D partin .stl format (for e.g. a",
"molds. I would require to add a hole to pour in liquid (resin",
"design and need to develop the CAD files for its mold. I will",
"I will then need to 3D print these molds. I would require to",
"requirement is as follows: I have an .stl file of a design and",
"its mold. I will then need to 3D print these molds. I would",
"develop the CAD files for its mold. I will then need to 3D",
"will then need to 3D print these molds. I would require to add",
"cylinder) and I want to make/design a mold for this object (i.e. the"
] |